ADVANCED FUNCTIONAL MATERIALS
·
2026
·
IF 19
Yifan Yuan,Kunpeng Zhao,Qingyong Ren,Haotian Gao,Yuxiang Zhan,Tian-Ran Wei,Ting Zhang,Xun Shi
Flexible thermoelectric materials offer a promising route toward self-powered wearable electronics. The emergence of ductile inorganic semiconductors opens a new paradigm for flexible TE technologies, yet their thermoelectric performance remains far from optimal. Herein, we reveal a pronounced phase-transition hysteresis in the Ag 2 (S, Se, Te) system, where the transition temperature during cooling is 20–40 K lower than that during heating. Leveraging this hysteresis behavior, we successfully stabilize different structural phases at ambient conditions simply by varying the thermal treatment protocol. Compared to the monoclinic phase obtained by slow cooling from high temperature, the orthorhombic phase obtained by liquid-nitrogen treatment exhibits worse plastic deformation but much better electrical transport. A maximum power factor of ∼16 µW cm −1 K −2 and a zT of ∼0.5 near room temperature are achieved in the orthorhombic phase, both of which surpass most reported Ag-based ductile thermoelectric materials. This work provides a new pathway for designing high-performance ductile thermoelectrics.
✓ 已验证
产品关联
DOI
高影响因子
Advanced Science
·
2026
·
IF 14.1
Haiwei Yang,Dongdong Ye,Yezi You,Ming Fu,Zongqian Wang
Eutectogels combining high mechanical and electrical performance hold great promise for next-generation wearable electronics. However, conventional polymerizable deep eutectic solvent (PDES)–based eutectogels suffer from an inherent strength–conductivity trade-off. Here, inspired by the multiscale architecture of the extracellular matrix, a bioinspired strategy is developed by integrating silk micro/nanofibrils (SMNF) as a reinforcing scaffold within a choline chloride/acrylic acid PDES. SMNF are generated in situ via deconstruction of silk fibers, while eutectic gallium–indium (EGaIn) microdroplets initiate polymerization without toxic initiators or high-energy UV irradiation, enabling one-step fabrication of SMNF-reinforced eutectogels (SMNF-Egel). The resulting SMNF-Egel combines dynamic hydrogen and coordination bonding with a robust micro/nanofibrous network, achieving a tensile strength of 1.25 MPa, toughness of 23.09 MJ m −3 , fracture strain of 2289%, and conductivity of 1.51 S m −1 , alongside skin-like modulus, self-healing, and environmental stability. These properties enable ultrasensitive strain sensing, Morse code communication, and stable bioelectrical signal monitoring. This work establishes a sustainable route to high-performance silk-based eutectogels and provides a versatile platform for advanced wearable sensors and bioelectronic interfaces.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Advanced Optical Materials
·
2026
·
IF 7.2
Jialong Xu,Yubiao Yue,Zhishan Chen,Hongqiang Zhu,Shaoan Zhang,Yiqing Chen,Huiwang Lian,Yuzhen Wang,Jia Xu,Linhai Li,Yang Li
Rapid, instrument-free detection of mercury ions (Hg 2+ ) is critical for addressing environmental emergencies, yet current methods face limitations in poor portability and sensitivity. Herein, a deep learning-optimized paper-based kit that incorporates controllable turn-off fluorescence of metal halide perovskite for instrument-free time-critical Hg 2+ detection by the dynamic quenching mechanism and ensures visual discernment at 2 ppb, achieving a 1000-fold sensitivity improvement over commercial strips is presented. Furthermore, a smartphone app powered by the deep learning model (MobileViT) further optimizes sensitivity, achieving ultrasensitive quantification (0.11 ppb limit of detection) across a 0.2–200 ppb linear range (R 2 = 0.987) with 98% overall accuracy, and the whole detection is completed only within 5 min. This approach of instrument-free time-critical Hg 2+ detection anticipates a new paradigm for rapid and on-site Hg 2+ monitoring in environmental and industrial settings.
✓ 已验证
产品关联
DOI
高影响因子
ADVANCED FUNCTIONAL MATERIALS
·
2026
·
IF 19
Xuefeng Sha,Shiru Wu,Peng Gao,Zixing Wang,Fan Zeng,Wang Zhou,Xueli Wu,Minghao Yu,Jiaxu Yan,Xianyin Song,Jilei Liu,Changzhong Jiang
The self-discharge phenomenon remains a fundamental challenge that limits the practical deployment of advanced supercapacitors, particularly in MXene-based systems where the interfacial ion-electron coupling dominates charge redistribution dynamics. Here, a surface terminal engineering strategy was proposed by utilizing 1,2-bis(triethoxysilyl)ethane (BTSE) to construct a surface passivation layer through hydrogen-bond-mediated assembly. Benefiting from the generated tension effect between BTSE and MXene, it directly results the weakened hybridization effect between Ti atoms and surface terminal atoms, together with an upward shift of the d -band center and reduce of reaction energy barriers. Collectively, the passivation of surface Ti–O terminals promotes the electron transfer kinetics (Ti–O + e − + H + → Ti-OH) and inhibits the dissociation of Ti-OH terminal from the perspective of electron transfer coupling. As a result, the optimized MXene@BTSE electrode has effectively reduced the Ti–OH dissociation rates by 2.23-fold and demonstrates a remarkable self-discharge suppression, achieving 55.16% decrease of self-discharge rate in 1 m H 2 SO 4 electrolyte, compared to the pristine MXene. Moreover, the modified MXene electrode shows around 92.43 % capacitance retention over 80 000 cycles, demonstrating excellent stability. This work establishes an electron-structure-property paradigm for interfacial design in electrochemical energy storage systems.
✓ 已验证
产品关联
DOI
高影响因子
Advanced Energy Materials
·
2026
·
IF 26
Xianghui Shi,Zhihao Zhang,Liuxin Xu,Zhe Wang,Qianjiang Mao,Yue Jiang,Xiaoxin Yang,Zihao Ma,Dan Cheng,Wenkun Jiang,Mingzhen Hu,Kebin Zhou
Globally, the proton exchange membrane water electrolyzers (PEMWEs) already account for approximately 30% of the hydrogen market and are undergoing rapid expansion. However, the commercially used iridium-based anodic oxygen evolution reaction (OER) catalysts in PEMWEs still suffer from notably poor reactivity. At present, the oxide pathway mechanism (OPM) is an important route to achieve both high activity and durability in OER. Nevertheless, the performance of conventional Ir-based crystalline OER catalysts following the OPM pathway remains far below their theoretical limit, which is significantly hindered by two intrinsic limitations. First, their rigid lattice structures prevent the shortening of metal-metal distances, which is essential to facilitate the rate-determining O * ─O * dimerization. Second, the repulsion between O * adsorbates during OER inevitably weakens the metal = O * bond and undermines the overall oxygen evolution efficiency. Herein, we report that an amorphous IrMO x catalyst elegantly overcomes the limitations of the OPM pathway by virtue of its dynamic surface structure and strong oxophilicity of M. The dynamic surface structure promotes O * ─O * coupling, while the oxophilic nature of M compensates for the inherent weakening of the metal = O * bond during OER. Because of that, the catalyst exhibits outstanding OER performance, along with excellent catalytic durability over 1200 h’ PEM testing.
✓ 已验证
产品关联
DOI
高影响因子
Advanced Optical Materials
·
2026
·
IF 7.2
Yuying Yang,Zhijun Wang,Junjie Xiong,Juan Zhang,Yuxuan Liang,Guodong Zhang,Hao Suo,Panlai Li
As a carrier for mechanical-to-optical conversion, mechanoluminescent (ML) materials are driving innovations in anti-counterfeiting encryption, self-powered sensing, and human-machine interaction, with their core value lying in the transformation of “invisible mechanical forces” into “visible light.” However, current ML materials face challenges, including weak emission intensity, limited luminescence modes, and the absence of a unified mechanism for force-to-light conversion. Here, a high-intensity green ML phosphor, Ca 2 GeO 4 : Tb 3+ , visible under ambient light, is developed. Following pre-irradiation, excellent photoluminescence (PL) and persistent luminescence (PersL) are observed. Notably, tunable emission from blue to green is achieved in the PL through increasing the Tb 3+ doping concentration, and PersL remained detectable after 1 h, suggesting applicability in delayed bioimaging and advanced anti-counterfeiting systems. Furthermore, it is revealed that the synergy between multiple trap levels and the piezoelectric field generated by lattice distortion induced by Tb 3+ substitution for Ca 2+ is identified as a key contributor to high intensity ML in Ca 2 GeO 4 : Tb 3+ , which is of significant importance for clarifying the force-to-light conversion mechanism. Remarkably, owing to its outstanding luminescent properties, the phosphors are integrated with polydimethylsiloxane (PDMS), demonstrating tremendous potential in multi-modal encryption, dynamic anti-counterfeiting, remote monitoring, and human-machine interaction.
✓ 已验证
产品关联
DOI
高影响因子
Advanced Science
·
2026
·
IF 14.1
Wendan Zhang,Jiaming Gong,Leiqian Zhang,Zeng Liu,Jia You,Zhaoyang Wang,Yang Zhou,Chao Zhang,Elke Debroye,Jean-François Gohy,Johan Hofkens,Yue-E. Miao,Feili Lai,Tianxi Liu
Aqueous zinc-iodine batteries (ZIBs) have attracted extensive attention due to their advantages of high theoretical specific capacity, abundant reserves, high safety, and low cost, while the Zn anodes are still suffering from dendrite growth, side reactions, and polyiodide corrosion, seriously affecting the service life of ZIBs. Herein, sulfonated cellulose acetate (SCA) nanofiber membrane with zincophilic-hydrophobic property is constructed on the Zn anode as a protective layer by electrospinning to circumvent the above problems and achieve a stable Zn anode. Attributing to both the hydrophobicity and zincophilicity, the SCA nanofiber membrane not only reduces the activity of water but also promotes the Zn 2+ desolvation. Moreover, negatively-charged groups of the SCA nanofiber membrane cause electrostatic repulsion with polyiodide. Density functional theory calculations and COMSOL simulations further reveal that the SCA nanofiber membrane can tune the uniform 3D deposition behavior of Zn 2+ by chemisorption and physical structure, respectively. The obtained ZIBs can achieve ultra-long life span (> 13000 cycles) with high-capacity retention (96.74%) and reversibility (average CE: 99.83%), demonstrating the reliability of our proposed strategy for achieving stable and high-performance ZIBs.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
POLYMER ENGINEERING AND SCIENCE
·
2026
·
IF 3.2
Jinhe Gao,Shuangle Xue,Caizhao Liu,Mehdi Derradji,Mianyuan Wu,Yize Wu,Zhigang Yuan,Mingming Sun,Xugang Zhang,Jianhui Li,Bin Zhang
This study reports the synthesis of a eugenol-derived benzoxazine resin (AEM) from 3-ethynylaniline and bio-based eugenol, and its structural characterization using Fourier transform infrared spectroscopy (FTIR) and proton nuclear magnetic resonance ( 1 HNMR). Subsequently, the AEM resin was copolymerized with bisphenol-type epoxy resin (E51) in varying proportions to form an EP-AEM modified resin system, whose processability, dynamic thermomechanical properties, thermal stability, dielectric properties, mechanical properties, and adhesion performance were investigated. The flexural strength, tensile strength, and elongation at break of EP-2AEM resins were 7.6%, 53.7%, and 41.2% higher than EP resins, respectively. In particular, AEM markedly increases the residual carbon yield ( Y c ) after high-temperature combustion in a nitrogen atmosphere, and this improvement becomes more pronounced as the AEM concentration increases. Compared with neat EP resin (14.92%), EP-4AEM resin exhibits a significantly higher value (21.59%). The high-temperature adhesion strength of EP-2AEM increases by 51.5%. Moreover, EP-4AEM shows the lowest dielectric constant (2.49) and dielectric loss tangent (0.022). Highlights AEM improves the comprehensive performance of epoxy resin.
✓ 已验证
产品关联
DOI
高影响因子
Laser & Photonics Reviews
·
2026
·
IF 10
Xujiang Liu,Yang Xu,Ling Luo,Yuanheng Mu,Mavlanjan Rahman,Pengpeng Dai,Xiaojun Wang
Achieving near-infrared (NIR) phosphors with broadband emission, robust thermal stability, high internal quantum efficiency (IQE), and excellent chemical durability remains a longstanding challenge, largely due to the fundamental trade-off between structural rigidity and flexibility. Here, we overcome this constraint by designing a novel series of garnet-type phosphors, BaY 2 Ga 4- x GeO 12 : x Cr 3+ (BYGG: x Cr 3+ ). The optimized composition BYGG:0.06Cr 3+ delivers an IQE of 93%, remarkable anti-thermal quenching behavior (103% emission retention at 423 K), and outstanding chemical stability (retaining 97% emission after 35 days in water). Notably, fine-tuning the Cr 3+ concentration broadens the emission bandwidth from 77 to 194 nm while preserving strong thermal stability (93%@423 K). This exceptional performance arises from the synergistic combination of ultra-high structural rigidity (Debye temperature, Θ D = 987 K), wide bandgap (5.10 eV), weak crystal field strength, and optimized 4 T 2 excited-state population. A fabricated NIR phosphor-converted LED (pc-LED) device demonstrates an NIR radiated power of 189.35 mW at 100 mA and a photoelectric conversion efficiency up to 12%. These results establish NIR phosphor BYGG: x Cr 3+ as a promising candidate for next-generation NIR pc-LED applications in night vision, non-destructive inspection, and biomedical imaging.
✓ 已验证
产品关联
DOI
高影响因子
RARE METALS
·
2026
·
IF 11
Jun-Xiao Wu,Xing-Liang Luo,Pu-Wei Zhai,Ming-Hui Long,Yuan Xue,Xiu-Xia Yang,Xu-Hui Xu
en This link goes to a English section zh This link goes to a Chinese section X-ray delayed imaging technology leverages an “irradiation-storage-thermally stimulated readout” mode, demonstrating unique advantages in intermittent monitoring scenarios such as high-temperature/high-radiation environments. This typically requires materials combining abundant carrier-trapping energy levels with structural thermostability. Herein, Cr 3+ -doped ZnGa 2 O 4 glass ceramics (ZGC GCs) serve as a functional platform, utilizing their deep trap energy levels (main peak 197.7°C) to efficiently capture and store X-ray imaging information, and achieve high-brightness X-ray delayed imaging by modulating the thermally stimulated detrapping rates. Under its exceptional structural thermostability and deep trap characteristics, ZGC GCs maintain high-quality delayed imaging capability by thermal stimulation even after 180°C irradiation, highlighting their potential for high-temperature nondestructive testing and surpassing the high-temperature failure threshold of conventional scintillators. This work pioneers functional applications of glass ceramics in high-temperature irradiation scenarios and offers a novel perspective for selecting harsh-environment-adapted X-ray imaging materials. 摘要 en This link goes to a English section zh This link goes to a Chinese section X射线延迟成像技术通过“辐照-存储-热激励读取”模式, 在间歇性监控场景(如高温/高辐射环境)中展现独特优势, 而热激励读取过程往往需要材料具备优异的结构热稳定性。本文以Cr 3+ 掺杂ZnGa 2 O 4 透明玻璃陶瓷(ZGC GCs)为载体, 利用其深陷阱能级(主峰197.7°C)高效捕获并存储X射线成像信息, 通过调节热激励脱陷速率实现高亮度X射线延迟成像。基于其优异的结构热稳定性及较深的陷阱能级, 在180°C高温环境下辐照后, ZGC GCs仍可通过热激励实现高质量延迟成像, 凸显其在高温无损检测领域的突出潜力, 突破传统闪烁体高温失效瓶颈。我们的工作为透明玻璃陶瓷的高温辐照功能应用开创了新方向, 并为恶劣环境适用型X射线成像材料的选择提供了新视角。
✓ 已验证
产品关联
DOI
高影响因子
MACROMOLECULAR CHEMISTRY AND PHYSICS
·
2026
·Vol. 227
·期 2
·e00468
·
IF 2.7
Songsong Li,Yuliang Liu,Chunqi Wang,Yunjiao Deng,Shiling Jia,Zhongyu Fu,Huixuan Zhang
This study investigates the microscale dual-diffusion process of polyacrylonitrile (PAN) solutions in the coagulation bath and the process of PAN fiber formation. The interaction peaks assignment between solvent and water were identified by analyzing the Fourier transform infrared spectroscopy (FTIR) characteristic peaks of red or blue shift. The time-resolved attenuated total reflection FTIR technique was employed to analyze the dual-diffusion process. Enabling quantitative determination of diffusion coefficients based on Fick's second law. A correlation was established between diffusion coefficients, the microstructural characteristics of PAN membranes and the cross-sectional morphology of PAN nascent fibers. Additionally, examination of the microstructure of triple times stretched PAN nascent fibers revealed the formation mechanism of fibers with “Fibrils Within a Filament”.
✓ 已验证
产品关联
DOI
高影响因子
Carbon Neutralization
·
2026
·Vol. 5
·期 1
·e70118
·
IF 12
Baoqian Yang,Tsz Lok Wan,Xinru Wu,Dong-Hau Kuo,Haoyu Wang,Kening Xiang,Cuizhu Li,Tao Liu,Dongfang Lu,Jinguo Lin,Xiaoyun Chen
Recent studies have indicated that the heterovalent states and vacancy defect structures in bimetallic oxysulfide play a crucial role in pollutant reduction reactions. However, systematic investigations into the synergistic coupling between heterovalent states and vacancy defect structures during the photocatalytic hydrogen evolution reaction (PHER) remain scarce. Herein, a tungsten/oxygen (W/O) co-doped Ag 2 S bimetallic oxysulfide (AgWOS) with heterovalent W 5+ /W 6+ states and sulfur vacancy (Vs) defects was synthesized via a facile thermohydrolysis method. The combination of W-doping and hydrazine-driven conditions induces abundant Vs defects, which act as active sites for water adsorption and activation, thereby facilitating proton generation in the PHER process. Moreover, the hydrazine-driven condition promotes the formation of heterovalent W 5+ /W 6+ states, which provide efficient electron transfer channels between W 5+ and W 6+ to boost PHER performance. The optimized AgWOS-2 with a balanced heterovalent n (W 5+ )/ n (W 6+ ) ratio and a high concentration of Vs achieves an impressive PHER rate of 1074.2 µmol·h −1 and an apparent quantum efficiency of 6.21% at 420 nm in pure water. Density functional theory calculations reveal that the synergy between heterovalent states and vacancy defects lowers the water dissociation barrier, accelerates *H generation, and boosts electron transfer between W 5+ and W 6+ . Moreover, S-3 p and O-2 p orbital hybridization suppresses photocorrosion and improves catalyst stability, enabling AgWOS-2 to retain 91.6% of its initial PHER activity after ten cycles. This study elucidates the synergistic interaction mechanism between heterovalent states and vacancy defects in a bimetallic oxysulfide, offering valuable insights for the rational design of efficient and durable PHER catalysts.
✓ 已验证
产品关联
DOI
高影响因子