JOURNAL OF CHEMICAL AND ENGINEERING DATA
·
2019
·
IF 2.298
Xiaoyi Chen,Shenda Jin,Yitong Dai,Jianzhou Wu,Yongsheng Guo,Qunfang Lei,Wenjun Fang
Densities (ρ) and viscosities (η) for the ternary system of decalin (1) + methylcyclohexane (2) + cyclopentanol (3) and three corresponding binary systems have been measured over the whole composition range at 11 temperature points from 293.15 K to 343.15 K under atmospheric pressure (0.1 MPa). The excess molar volumes (VmE) and viscosity deviations (Δη) of binary systems have been calculated and further fitted with the Redlich–Kister equation, while corresponding physical data of the ternary system have been correlated via the Clibuka, Singh, Nagata-Tamura, and Redlich–Kister equations. The VmE values are negative for the binary system of decalin (1) + methylcyclohexane (2) with a minimum when the moles of the two components are similar. For the system of decalin (1) + cyclopentanol (2), the VmE values are always positive with a maximun at about x1 = 0.6. At the same time, a sigmoid curve can be observed for the system of methylcyclohexane (1) + cyclopentanol (2). The minimum and maximum appear around x1 = 0.2 and x1 = 0.9, respectively. The Δη values of the three binary systems are all negative and the absolute values decrease with increase in temperature. For the ternary system, the VmE values are partially negative and the Δη values are negative over the entire concentration range. The nonideal behaviors of the mixtures are discussed in the perspective of intermolecular interaction and structural effect.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF CHEMICAL AND ENGINEERING DATA
·
2019
·
IF 2.298
Xingchang Cha,Jun Gao,Yi Zhang,Ziqi Cui,Dongmei Xu,Lianzheng Zhang,Yinglong Wang
For the purpose of separating nitrogen compounds, pyrrole and indole, N-methylformamide (NMF) was selected as the extractive solvent. The liquid–liquid equilibrium (LLE) data for {NMF + pyrrole/indole + alkanes} systems were measured at 298.15 K under atmospheric pressure of 101.3 kPa. The triangular diagrams of the above eight systems, {NMF + pyrrole/indole + n-hexane/n-heptane/n-decane/n-dodecane}, were classified as Treybal’s type I. Meanwhile, the nonrandom two-liquid (NRTL) and universal quasi-chemical (UNIQUAC) activity coefficient models were applied to correlate the LLE data, and the UNIQUAC model shows better agreement than the NRTL model. In addition, the distribution constant and selectivity factor were calculated on the basis of the experimental data and utilized to investigate the extraction capabilities of NMF for pyrrole and indole.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF CHEMICAL AND ENGINEERING DATA
·
2018
·
IF 2.196
Xinyi Wang,Dejiang Zhang,Shiyuan Liu,Yifu Chen,Lina Jia,Songgu Wu
The solubility of imatinib mesylate in nine monosolvents and two binary solvents was determined by the shaken flask method followed by UV composition analysis from 278.15 to 318.15 K at atmospheric pressure. The solubility increases with the increasing of temperature in all solvents we chose. Meanwhile, the dissolving capacity of imatinib mesylate ranks as methyl acetate < 2-propanol < acetonitrile < isobutanol < 1-butanol < tetrahydrofuran < 1-propanol < ethanol < methanol. The Apelblat model, λh equation, and nonrandom two-liquid (NRTL) model described the solubility data of imatinib mesylate in monosolvents; simultaneously, the Apelblat model, combined nearly ideal binary solvent/Redlich-Kister model, and NRTL model were employed in binary solvents. The results show a satisfactory correlation with the experimental data. Additionally, mixing thermodynamic properties of imatinib mesylate were calculated based on the NRTL model, which reveals the mixing process is spontaneous and exothermic.
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF THERMOPHYSICS
·
2018
·Vol. 39
·期 5
·1-11
·
IF 0.829
Fan Desong,Sun Si,Guo Li
A novel thermal control coating was presented based on the thermochromism of manganite. The pigment of K-doped manganite nanoparticles was dispersed into polymer matrix to prepare the coating with curing below 200 \(^{\circ }\) C. The nanoparticles size mainly distributes around 100–200 nm, and it shows a comparable stoichiometric ratio. The phase transition of the nanoparticles was observed from ferromagnetic metallic to paramagnetic insulator state. With increasing K doping level, the phase transition temperature increases, achieving controllable adjustment. Coating surface with and without pore defect was obtained by different polymer matrix. A sharp emittance variation was observed with increasing temperature in K-doped coating. The variation magnitude of emittance is up to 0.46, which is attractive to space thermal control. It is suggested that the pigment content of 50 wt% is sufficient to realize a large emittance variation.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF CHEMICAL AND ENGINEERING DATA
·
2017
·
IF 2.323
Jingyu Wu,Lianzheng Zhang,Dongmei Xu,Jun Gao,Kai Zhang,Meng Kong
The solubility of sodium thioglycolate in five pure solvents of water, methanol, ethanol and isopropyl alcohol, n-propanol and four binary solvent mixtures (water + methanol, water + ethanol, water + isopropyl alcohol, water + n-propanol) was determined within the temperature range from (293.15 to 333.15) K by using the gravimetrical method under atmospheric pressure (p = 0.1 MPa). The solubility of sodium thioglycolate in water, ethanol, isopropyl alcohol, and n-propanol increases with a rise of temperature, but the solubility decreases in methanol with increasing temperature. Meanwhile, in the binary solvent mixtures (water + methanol, water + ethanol, water + isopropyl alcohol, water + n-propanol), the solubility of sodium thioglycolate increases with increasing the mole fraction of water and with temperature. The modified Apelblat equation and van’t Hoff equation were applied to correlate the solubility of sodium thioglycolate in the five pure solvents, while in the binary solvent mixtures, the solubility was correlated by the modified Apelblat equation, CNIBS/R-K model, and Jouyban–Acree model. It was shown that the correlated results were in better agreement with the experimental data. Also, the mixing thermodynamic properties for sodium thioglycolate in the binary solvent mixtures were calculated.
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES
·
2017
·
IF 3.671
Chao Liu,A.M. Omer,Xiao-kun Ouyang
In the present study, new composite beads based on carboxymethyl cellulose (CMC)/k-carrageenan (kC)/activated montmorillonite (AMMT) were prepared for adsorptive removal of cationic methylene blue (MB) as a dye model. The structure and morphology of the composite beads were investigated by FT-IR and SEM, while the thermal properties were tested using TGA. Factors affecting the removal percent of MB such as CMC/kC/AMMT ratios, initial MB concentration, pH medium, adsorbent dosage, solution temperature, and agitation speed were also explored. Results demonstrated that MB removal (%) exceeded 92% after 120 min using CMC/kC/AMMT (1:1:0.4 ratio) compared to 69% in case of free AMMT beads. Moreover, data obtained from isotherm studies were fitted well to Langmuir model (R 2 = 0.999), and the kinetics of adsorption followed pseudo-second order model. Finally, the composite beads showed good reusability for MB dye removal with high efficiency. Results obtained from this study suggest that the prepared composite beads could be applied effectively for removing cationic dyes from aqueous solutions.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Biomass Conversion and Biorefinery
·
2024
·
IF 3.5
Yao Pin,Yan Tinggui,Dai Xin,Xiao Ya,Xiang Weixue,Wu Yunqi
Deposition and corrosion in boilers caused by the release of alkali compounds in agricultural residua pose significant challenges to the widespread utilization of biomass energy. Phosphate tailings (PT), which is rich in Ca, Mg, and P, have the potential to mitigate the potassium (K) release of biomass straw. However, the impact of PT on K immigration has not been investigated. To elucidate the influence of PT on K immigration, thermal analysis, K concentration determination, and mineral evolution during heating of ash were conducted. These results were compared with those obtained from biomass mixed with kaolin, an effective additive known to alleviate K release in biomass. The findings revealed that PT resulted in lower K release at temperatures below 600 ℃ compared to kaolin. Because the reaction between PT and K-compounds to form K-phosphate occurs more readily than the formation of K-silicate at lower temperatures. However, the effectiveness of PT diminished as the temperature increased. One reason is the decomposition of K-phosphate, resulting in the volatilization of K at higher temperatures. Another reason is the competition among Ca, Mg, and K for the opportunity to react with Si and Al, leading to the formation of more stable Ca and Mg aluminosilicate and facilitating the release of K. It is noteworthy that the addition of kaolin to rice straw causes a violent release of K in 1000–1200 ℃. This can be attributed to the surplus of Si in the system, promoting the release after the eutectic melting between K-silicate and SiO 2 .
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF CHEMICAL AND ENGINEERING DATA
·
2017
·
IF 2.323
Shenfeng Yuan,Jiafeng Liu,Hong Yin,Zhirong Chen
Liquid–liquid equilibrium (LLE) data for the quaternary systems of ethanol + butanol + octane + water and ethanol + butanol + nonane + water were obtained at 298.15 K under atmospheric pressure in this article. The nonrandom two-liquid (NRTL) equation was used to correlate the LLE data, and the two quaternary systems were used to regress the interaction parameters of the model. The obtained interaction parameters of NRTL model were used to predict the LLE of the quinary system ethanol + butanol + octane + nonane + water and was compared with the experimental values. The results showed that the calculated values coincided with the experimental data well, an indication that the NRTL model and the interaction parameters obtained from quaternary systems could be used to predict the LLE data of quinary system. The LLE data of the quinary system were also characterized by the distribution coefficient and the selectivity, and the results showed that the ethanol aqueous solution which contained about 40 wt % ethanol was suitable for separating butanol from the butanol–octane–nonane mixture.
✓ 已验证
产品关联
DOI
高影响因子
Asia-Pacific Journal of Chemical Engineering
·
2016
·Vol. 11
·期 2
·305-313
·
IF 0.728
Xing Li,Lei Bei,Zhi Sun,Kun Liu,Xu Zhang,Xiaozhao Han
The study aimed at investigating the addition effects of P, K, and micronutrient fertilizers on the permeability of N-nutrient fertilizer urea through a representative polymer membrane, which is of great importance in polymer-coated compound fertilizer. Specifically, the permeability of urea through polystyrene membrane was determined experimentally at the nominal temperature of 298 K using the Ussing chamber method for fertilizer solutions of urea–water, urea–NaH 2 PO 4 –water, urea–Ca(H 2 PO 4 ) 2 –water, urea–KCl–water, and urea–NaCl–water. The experimental data showed that the addition effects of NaH 2 PO 4 , KCl, and NaCl on urea permeability were pronounced and could be promotion or suppression depending on the amounts added. The variation of urea permeability with additive concentration could be explained by the ‘solution–diffusion’ model, suggesting that the specific intermolecular and interionic interactions in the permeation solution were an important factor determining the permeability. Using the saturated urea–water solution as basis, the addition of saturated KCl increased the urea permeability by 2.5 times, while the addition of saturated Ca(H 2 PO 4 ) 2 and NaH 2 PO 4 decreased the permeability by 41% and 76%, respectively. © 2016 Curtin University of Technology and John Wiley & Sons, Ltd.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF CHEMICAL THERMODYNAMICS
·
2016
·
IF 2.196
Peipei Zhu,Yanxin Chen,Meijing Zhang,Ying Bao,Chuang Xie,Baohong Hou,Junbo Gong,Wei Chen
In this work, the solubility of 1,3-dimethylurea form I (DMUI) in seven solvents including water, 2-butanol, 2-propanol, acetone, acetonitrile, ethyl acetate and butyl acetate were measured by a synthetic method at a temperature range from (288.15 to 328.15) K at atmospheric pressure. For the temperature range investigated, the solubility of DMUI in the selected solvents increased with increasing temperature. Results of these measurements were well-correlated with the modified Apelblat equation, λh equation, van’t Hoff equation and Wilson model. Besides, the thermodynamic data ( i.e. , Gibbs energy, enthalpy, and entropy of mixing) were calculated by using the Wilson model. The chemical potential, solvation free energy and interaction enthalpy of DMU in solution were calculated by COSMO-RS model. This model was also applied to predict DMU solubility which showed good agreement with the experimental values.
✓ 已验证
产品关联
DOI
高影响因子
ANALYTICAL CHEMISTRY
·
2017
·
IF 6.32
Lu Li,Yuanyuan Fan,Qingling Li,Renjie Sheng,Haibin Si,Juan Fang,Lili Tong,Bo Tang
Various intracellular metal ions have closely related functional roles in the nervous system. An excess or deficiency of essential metal ions can contribute to neurodegenerative diseases. Thus, the detection of various metal ions in neurons is important for diagnosing and monitoring these diseases. In particular, single-cell analysis of multiple metal ions allows us to not only understand the cellular heterogeneity and differentiation but also determine the actual relationships among multiple metal ions in each individual cell. Aiming at the low efficient single-cell manipulation and interference of complex biological matrices within cells in the existing method for single-cell metal ion detection, in this manuscript, we present a convenient, sensitive, and reliable method to simultaneously identify and quantify multiple metal ions at the single-cell level using a microfluidic system. Using the combination of on-chip electrophoresis separation and multicolor fluorescence detection, we achieved the simultaneous analysis of Na+, K+, Ca2+, and Mg2+ in single PC-12 cells and studied changes in these four metal ions in Aβ25–35-treated PC-12 cells, which is a model of Alzheimer’s disease (AD). The data showed that metal ions imbalances in neuron-like cells may be associated with AD induced by Aβ25–35. This method paves the way for multiple metal ion detection in single neuron-like cells, and the results provide insights regarding synergistic function of multiple metal ions in regulation of neurological diseases at the single-cell level.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
FLUID PHASE EQUILIBRIA
·
2016
·
IF 1.846
Yemin Yu,Tao Li,Yonghong Hu,Wenge Yang,Yuhao zhang,Renlun Deng,Min Jiang
Research on relevant solid–liquid equilibrium of drug Norfloxacin (NFLX) in different solvents is necessary for an elementary study of industrial implantation. In this work, the solid–liquid equilibrium of NFLX in ethanol, 1-butanol, isopropanol, acetone, acetonitrile , ethyl acetate , N-hexane, N,N-dimethylformamide single pure solvent and in (N,N-dimethylformamide + ethyl acetate) binary solvent mixtures were probed under atmosphere pressure at desired temperatures from 278.15 K to 328.15 K. The Gibbs energy , enthalpy, and entropy of solution were obtained from these solubility data. The modified Apelblat model, the Buchowski–Ksiazaczak λh model, Redich-Kister (CNIBS/R-K) model, Jouyban-Acree model, ideal model and the Van't Hoff analysis were applied to depict and forecast the diversification tendency of solubility. The satisfactory simulation results were obtained. Moreover, the thermodynamic functions for NFLX dissolution from calculation, using the van't Hoff and Gibbs equations, imply that in each studied solvent and in binary solvent mixtures, the process of NFLX dissolution is endothermic. Based on the above analysis, N,N-dimethylformamide is checked as the best solvent and ethyl acetate can be used as an effective anti-solvent in the crystallization process of NFLX.
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）