APPLIED CATALYSIS B-ENVIRONMENTAL
·
2022
·
IF 24.319
Xinxin Han,Bingjie Lu,Xin Huang,Cheng Liu,Shixia Chen,Jingwen Chen,Zheling Zeng,Shuguang Deng,Jun Wang
S-scheme photocatalysts are more efficient than the conventional type-II configuration, but the CO 2 reduction performances are still unsatisfactory. Herein, we firstly report the layered double hydroxide (LDH) based S-scheme heterostructure photocatalyst (NiIn LDH/In 2 S 3 ) with n-type NiIn LDH and p-type In 2 S 3 . The built-in internal electric field directs the photogenerated electrons flow from the conductive band of In 2 S 3 to the valance band of NiIn LDH, which is confirmed by operando and theoretical experiments. The CO 2 photoreduction intermediates are monitored by in-situ Raman spectra, and the density functional calculations disclose the reduced energy barrier for CO desorption on the heterojunction. Therefore, without cocatalysts or sacrificial agents, the NiIn LDH/In 2 S 3 heterojunction delivers a high CO yield rate of 29.43 μmol g −1 h −1 under visible light irradiation, ca. 3.5 and 4.3 times higher than the single counterpart NiIn LDH and In 2 S 3 . Notably, this value is the highest among S-scheme CO 2 photocatalysts and surpasses most top-ranking benchmarks.
✓ 已验证
产品关联
DOI
高影响因子
SOLAR ENERGY MATERIALS AND SOLAR CELLS
·
2022
·
IF 7.305
Xiatong Qin,Bin Xu,Jianjun Lin,Jiaqi Chen,Hanyu Tong,Ye Chen,Pingxiong Yang,Junhao Chu,Lin Sun
Electrodeposition is a promising method to fabricate Cu 2 ZnSn(S,Se) 4 (i.e., CZTSSe) absorber layer thanks to its many advantages such as low-cost and large-scale. However, the secondary phases and intrinsic defects in electrodeposited CZTSSe solar cells inevitably limit the photoelectric performance. Herein, two different kind of precursor films (binary-ternary selenide vs. quaternary selenide) are deliberately fabricated and the effect of these precursors on the secondary phases and intrinsic defects of CZTSSe absorber layer are investigated comprehensively. The absorber layer obtained from binary-ternary selenide precursor has a small amount of ZnSe secondary phases and Cu Sn deep defects , whereas that obtained from the quaternary selenide precursor exhibits the favorable V Cu shallow defects, which is beneficial to the efficiency improvement in CZTSSe. Based on the quaternary selenide precursor film, the CZTSSe solar cell with 10.03% total area efficiency (the active area efficiency is 10.9%) was obtained. This is the highest efficiency of CZTSSe solar cells prepared by the electrodeposition method.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2022
·
IF 16.744
Jie Zhao,Yuyan Zhao,Wen-ce Yue,Xue Li,Ning Gao,Yu-jiao Zhang,Chao-quan Hu
The shuttle effect caused by soluble lithium polysulfides (LiPSs) hinders the practical application of lithium–sulfur batteries. The sluggish reaction kinetics of LiPSs results in rapid capacity decay. In this work, we constructed a free-standing multifunctional interlayer decorated with V 2 O 3 /VN catalysts to suppress the shuttle effect and boost the redox reaction kinetics. The introduction of VN with strong chemical adsorption improves the conductivity of V 2 O 3 , which is beneficial for the kinetics of conversion reaction. In addition, the micro/mesopores inside the structure not only facilitate ion diffusion but also buffer the volume change of the sulfur cathode during the cycling process. Benefiting from the synergistic effects, the fabricated cells exhibit a high specific capacity of 1419.5 mAh g −1 at 0.1C. The cell with V 2 O 3 /VN/C exhibits a promising cycling performance over 1000 cycles with a decay rate of 0.037% per cycle at 1C. The synergistic effects of electrocatalysts and conductive carbon material provide inspiration on the development of high-performance Li–S batteries.
✓ 已验证
产品关联
DOI
高影响因子
POLYMER
·
2022
·
IF 4.432
Bingxiu Xue,Fang He,Qi Lei,Xiaopeng Zhao,Jianbo Yin
Backbone, pendant and cross-linked poly(ionic liquid) (PIL) particles with the same ion pair and similar ion number density have been prepared and the electro-responsive electrorheological (ER) effect of their suspensions in insulating carrier liquid has been comparably studied by rheology and dielectric spectroscopy . It has found that the ER effect of cross-linked PILs is strongest and that of backbone PILs is weakest. Dielectric spectrum analysis has showed that the difference of ER effect is mainly due to the difference in the ion leakage and effective interfacial polarization of PIL particles under electric fields. Although the backbone PILs have the largest interfacial polarization strength , its ion leakage conductance is also largest and this results in its weakest ER effect. The cross-linked PILs well restrains the ion leakage conductance and the ER effect is largely enhanced. The difference in ion leakage conductance and ER effect is further related to the difference of PIL matrix structure according to X-ray diffraction characterization. This study clarified the influence of matrix structure on ER effect and dielectric polarization of PILs and provided a guidance for the design of PIL ER materials.
✓ 已验证
产品关联
DOI
高影响因子
Catalysts
·
2022
·Vol. 12
·期 3
·266
·
IF 4.501
Yue Gao,Qing-Bo Meng,Bao-Xin Wang,Yu Zhang,Hui Mao,Da-Wei Fang,Xi-Ming Song
Poly(ionic liquid)s nanofiber (PIL NF) membrane was derived from polyacrylonitrile by converting its cyano groups to imidazoline moieties via cyclization with ethylenediamine, followed by quaternization with 1-bromobutane. The novel PIL NF is further decorated with photocatalyst phosphotungstic acid PW12 via anion exchanging to give PW-PIL. The degradation rate of the novel supported photocatalyst towards methyl orange irradiated under visible light was found to be 98%. In addition, the nanofiber membrane morphology is beneficial for easy recycling, and 98% of original degradation rate was maintained after 5 cycles of photocatalysis degradation. This robust, efficient, and recyclable material offers a new approach for serving as catalyst supporter. The photocatalyst PW-PIL is reported for the first time. The inexpensive functional membrane is used to exploit the sun as a cheap and clean source of light.Keywords:poly(ionic liquid)s;polyacrylonitrile;nanofiber membrane;visible light photocatalyst
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF CONTROLLED RELEASE
·
2022
·
IF 11.467
Hong Liu,Zhitao Hu,Haolin Chen,Yanzi Yan,Zhicheng Le,Cong Wei,Wenqiang Cao,Tianfeng Chen,Yongming Chen,Lixin Liu
Vaccination with subunit nanovaccines is a promising strategy to combat virus infection and tumor development. However, immunogenicity of present nanovaccines is still unsatisfied for clinical translation. Here, we developed a nanovaccine loading a STING agonist, 2′3′-cGAMP and, a model subunit antigen, OVA , by using a well-defined self-degradable poly(β-amino ester)s to treat B16F10-OVA melanoma tumors. The polymer underwent slow hydrolysis at pH 5.5 but self-degraded induced by the amino groups along the polyester chain at pH > 6.5. It is shown that the self-degradation products facilitated the release of 2′3′-cGAMP and OVA from early endolysome to the cytosol, where the two components strongly activated CD8 + T lymphocytes (CTLs) and significantly enhanced Ifn1, TNF , Cxcl9, and Cxcl10 expression. In turn, the tumor microenvironment was remolded from cold to hot. Moreover, the nanovaccine could be quickly drained to sentinel lymph nodes after intratumoral injection. The nanovaccine with strong immunogenicity also could reduce the side effects of systemic inflammatory reaction caused by molecular 2′3′-cGAMP. The tumor progression of animals was inhibited, and their survival rates increased significantly. Thus, the multifunctional biodegradable material provided a new delivery system for a cancer vaccine to translate to clinics.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
BIOMASS & BIOENERGY
·
2022
·
IF 5.774
Guojun Hao,Hongying Liu,Zhibing Chang,Kechen Song,Xin Yang,Han Ma,Wenjing Wang
In this work, lignin depolymerization was examined over CoMo sulfide catalysts supported on different carriers in supercritical ethanol system. The temperature, time, MoS 2 and carrier effects on the lignin depolymerization were investigated. 95.76% liquefaction yield with negligible char was achieved over Co–Mo–S/ZrO 2 at 340 °C for 150 min. The liquid product was mainly composed of C 4 –C 8 alcohols, C 4 –C 10 esters and C 7 –C 10 aromatic compounds . The synergistic effect of active sites and acid-base sites on support played an important role in lignin depolymerization. Furthermore, the Co–Mo–S/ZrO 2 catalyst is reusable with 8% loss in liquefaction yield after 5 cyclic runs. We believe that acid/base carriers or additives that can promote the medium to generate abundant free radicals or ions to replace external hydrogen pressure are one of the prospects for the design of depolymerization lignin catalysts.
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2021
·
IF 7.312
Jiaqiang Wang,Donglin Yang,Bingxiao Feng,Meng Xiao,Hengjun Gai,Tingting Huang,Yu Zhou,Hongbing Song
Considering the environmental problems caused by oily wastewater, how to realize oil-water separation has attracted extensive attention from researchers. Herein, a series of hypercrosslinked poly(ionic liquid)s (HCPILs) were fabricated by using dimethoxymethane as an external crosslinking agent combined with different auxiliary crosslinking agents to “weave” the ionic liquid of 1,3-dibenzylimidazolium chloride for oil-water separation. The hydrophilicity and hydrophobicity of HCPL can be adjusted by changing different auxiliary crosslinking agents. When using aniline as an auxiliary crosslinking agent, the resulting HCPIL-A2 with approximately 5500 L/m 2 ·h of water flux exhibits super hydrophilicity-oleophobicity, its static water contact angle and underwater oil contact angle are close to 0° and 132°, respectively. When using benzyl alcohol instead of aniline, the obtained HCPIL-B2 exhibits good lipophilicity and hydrophobicity. Its static water contact angle and underwater oil contact angle are close to 126° and 0°, respectively. And its oil fluxes of chloroform and carbon tetrachloride are approximately 7645 and 7241 L/m 2 ·h, respectively. However, when using toluene instead of aniline, the obtained HCPIL-C2 exhibits hydrophilicity-lipophilicity and can’t separate the oil-water mixtures. Moreover, HCPILs show permanent pore structure, good stability, and environmental friendliness due to their high degree of crosslinking are constructed. Their loose surface roughness can realize the separation of the oil-water mixture by gravity. Therefore, the designed new materials can selectively remove water or oil mixture. Efficient separation of crude oil and seawater mixture will provide new ideas for future environmental problems such as offshore oil spills.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2023
·
IF 15.1
Yiding Li,Qiang Zhang,Simin Shen,Siqi Wang,Liangliang Shi,Dequan Liu,Yujun Fu,Deyan He
Effectively limiting the shuttle effect is the key to improving the electrochemical performance of Li-S batteries. Here, the synthesis of WO 3 -WS 2 heterostructures is reported by electrospinning and in situ sulfurization strategies, combining the initial WO 3 nanoparticles with the sulfurization product WS 2 . It was found that the obtained bifunctional heterostructures enhance the electrolyte wettability, optimize intermediate regulation performance, accelerate Li + /e − diffusion, and thus exhibit excellent electrochemical characteristics in Li-S batteries. Through experiments and density functional theory (DFT) calculations, the WO 3 -WS 2 heterostructures were considered as a coupled creative solution with multiple advantages. Different from the batteries using single-component or single-configuration catalyst, the prepared Li-S batteries with the WO 3 -WS 2 heterostructures exhibited synergistic enhanced electrochemical performance and high-temperature crushing resistance. Even under severe conditions, including high sulfur loading (10.3 mg cm −2 ), lean electrolyte (5.8 μL mg −1 ), high current density (7.0 A g −1 ), extended cycling (1600 cycles), and high temperature (90 °C), the representative battery exhibited stable cycling performance.
✓ 已验证
产品关联
DOI
高影响因子
SOLID STATE SCIENCES
·
2023
·
IF 3.5
Huadong Liu,Hao Sun,Du Ke Zhen,Cheng Jing liang,Sun XiaoYu
Monoclinic bismuth vanadate (m-BiVO 4 ) is a well-known photocatalytic material. However, its poor charge transport and photogenerated electron hole rapid recombination limit the application of m-BiVO 4 . In this paper, we successfully constructed a novel copper-sulfur co-doped carbon quantum dots (Cu, S-CQDs)/BiVO 4 nanocomposite through a facile and efficient route, which significantly improved the photocatalytic performance of BiVO 4 . The physicochemical properties of Cu, S-CQDs and Cu, S-CQDs/BiVO 4 samples were studied by various characterization. It was concluded from the degradation experiments that the photocatalytic degradation rate of rhodamine B reaches 99% in 60 min under natural light. The degradation curve compounds the quasi-primary kinetic model, and the kinetic coefficient of degradation is 0.07831 min −1 , which is 5.37 times than that of pure BiVO 4 . Moreover, the free radical scavenging experiments reveal that the hole and superoxide radicals play a major role in the photocatalysis process. After four cycles, the activity of photocatalyst exhibits high stability, which is extremely important for the photocatalytic process. In the summery, the prepared Cu, S-CQDs/BiVO 4 has many advantages, such as environmental-friendly, low cost and a wide range of applications.
✓ 已验证
产品关联
DOI
高影响因子
CHEMOSPHERE
·
2023
·
IF 8.8
Jie Tian,Yumeng Qi,Junyan Wei,Ahmed Rady,Saleh Maodaa,Ahmed A. Allam,Zunyao Wang,Ruijuan Qu
The degradation process of bisphenol S (BPS) in ozone/peroxymonosulfate (O 3 /PMS) system was systematically explored. The results showed that the removal efficiency of BPS by O 3 could be significantly improved with addition of PMS. Compared with ozonation alone, the pseudo-first-order constant ( k obs ) was increased by 2–5 times after adding 400 μM PMS. In O 3 /PMS system, accelerated removal of BPS was observed under neutral and alkaline conditions. The removal efficiency of BPS reached 100% after 40 s of reaction at pH 7.0, with the k obs of 0.098 s −1 . Moreover, Cu 2+ had a catalytic effect on the O 3 /PMS system, because it could catalyze the decomposition of ozone and PMS to produce •OH and SO 4 •- , respectively. Electron paramagnetic resonance illustrated that •OH and SO 4 •- were the reactive species in O 3 /PMS system. Twelve intermediates were identified by mass spectrometry, and the degradation reactions in O 3 /PMS system mainly included hydroxylation, sulfate addition, polymerization and β-scission. Finally, the toxicity of the products was evaluated by the EOCSAR program. Our results introduce an efficient method for BPS removal and would provide some guidance for the development of O 3 -based advanced oxidation technology .
✓ 已验证
产品关联
DOI
PubMed
高影响因子
DYES AND PIGMENTS
·
2026
·
IF 3.9
Ke Cheng,Tianyi Ma,Luoyilan Zhang,Hao Xue,Yin Yuan,Hong Zheng,Bin Liu
Coreopsis S/P-CDs from a CL sensor. • CL sensor detects Sudan III with 1.0 μM LOD. • Recoveries of 97.4% to 105.0% in real samples. A novel chemiluminescence sensor for Sudan III detection was developed using sulfur/phosphorus-doped carbon dots (S/P-CDs) synthesized from Coreopsis. Combined TEM, XPS, and FTIR analyses verified that the S/P-CDs exhibit uniform spherical morphology with well-resolved lattice fringes, successful S and P doping at atomic percentages of 3.6% and 1.7%, respectively, and abundant surface functionalities (including PO 4 3− and C O groups) that confer excellent water dispersibility and chemical reactivity. The S/P-CDs significantly enhanced the CL intensity of the acidic KMnO 4 -HCHO system. Under optimal conditions, the CL intensity was linearly correlated with the Sudan III concentration over the range of 5-100 μM, achieving a detection limit of 1.0 μM. The method was successfully applied to real samples, with recoveries of 97.4% to 105.0%, enabling rapid, convenient detection in food. Download: Download high-res image (366KB) Download: Download full-size image
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）