FUEL
·
2015
·
IF 3.52
Haimei Xu,Zhichao Miao,Huahua Zhao,Jian Yang,Jun Zhao,Huanling Song,Ning Liang,Lingjun Chou
In this paper, a series of ordered mesoporous zirconium oxophosphate with different P/Zr molar ratios (M-ZrPO- x ) were prepared via one-pot evaporation induced self-assembly strategy (EISA). The catalytic performance of M-ZrPO- x for the dehydration reaction of fructose to produce 5-hydroxymethylfurfural (5-HMF) was also studied. With high concentration of Brönsted and Lewis acid sites measured through NH 3 -TPD and pyridine-IR, M-ZrPO-0.75 performed high catalytic activity (up to 97.4%) and selectivity (79.6%) of 5-HMF under relatively mild conditions. Furthermore, M-ZrPO-0.75 performed excellent catalytic stability. Based on detailed analyses of XRD, SEM, TEM, BET and XRF, the structural, surface and textural properties of M-ZrPO-0.75 after reaction were investigated. Obtained results demonstrated that the mesostructure still retained even after twelve cycles, which may be ascribed to the “ordered” mesoporous properties and high thermal stability. In addition, a lower activation energy was obtained in this M-ZrPO catalytic system using dimethyl sulfoxide as solvent.
研究领域:
化学工程
·
催化
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
CHINESE JOURNAL OF CHEMICAL ENGINEERING
·
2021
·
IF 3.171
Xionghui Liu,Jianfeng Du,Yu Ye,Yuchuan Liu,Shun Wang,Xianyu Meng,Xiaowei Song,Zhiqiang Liang,Wenfu Yan
Nitrogen-rich porous organic polymers have shown great potentials in gas adsorption/separation, photocatalysis , electrochemistry, sensing and so on. Herein, 1,2,3-triazole functionalized triazine-based porous organic polymers (TT-POPs) have been synthesized by the copper-catalyzed azide-alkyne cycloaddition (Cu-AAC) polymerization reactions of 1,3,5-tris(4-azidophenyl)-triazine with 1,4-diacetylene benzene and 1,3,5-triacetylenebenzene, respectively. The characterizations of N 2 adsorption at 77 K show TT-POPs possess permanent porosity with BET surface areas of 666 m 2 ·g −1 (TT-POP-1) and 406 m 2 ·g −1 (TT-POP-2). The adsorption capacities of TT-POPs for CO 2 , CH 4 , C 2 H 2 and C 2 H 4 , as well as the selective separation abilities of CO 2 /N 2 , CO 2 /CH 4 , C 2 H 2 /CH 4 and C 2 H 4 /CH 4 were evaluated. The gas selective separation ratio of TT-POPs was calculated by the ideal adsorbed solution theory (IAST) method, wherein the selective separation ratios of C 2 H 2 /CH 4 and C 2 H 4 /CH 4 of TT-POP-2 was 48.4 and 13.6 (298 K, 0.1 MPa), which is comparable to other adsorbents (5.6–120.6 for C 2 H 2 /CH 4 , 10–26 for C 2 H 4 /CH 4 ). This work shows that the 1,2,3-triazole functionalized triazine-based porous organic polymer has a good application prospect in natural gas purification.
研究领域:
材料科学
·
化学工程
·
环境科学
✓ 已验证
DOI
高影响因子
ACS Applied Materials & Interfaces
·
2020
·
IF 8.758
Yangwen Liu,Qiao Liu,Lin Wang,Xianfeng Yang,Weiyou Yang,Jinju Zheng,Huilin Hou
Hollow carbon nanofibers with hierarchical porous shells were prepared by NaOH activation of the electrospinning SiCNO fibers, followed by carbonization treatment. By adjusting the carbonization temperature, porous hollow carbon nanofibers with different Brunauer–Emmett–Teller (BET) specific surface areas and total pore volumes are obtained, both of which are explored as electrode materials for supercapacitors. It was found that the obtained products (HCF800) possess the highest BET specific surface area of 2628.10 m2/g and the largest pore volume of 2.32 cm3/g when the carbonized temperature was designed at 800 °C, thus displaying the best supercapacitor performance. The electrochemical results in a three-electrode system show that HCF800 exhibits a high specific capacitance of 330.11 F/g as the discharge current density is 1 A/g and still maintains 65.3% of its original specific capacitance when the current density reaches 20 A/g. Moreover, in a two-electrode system, HCF800 also exhibits an excellent specific capacity of 259.86 F/g at a current density of 1 A/g, marvelous cyclic stability with the specific capacitance retention of 95.3% even after 10,000 cycles, and a large energy density of 12.99 W h/kg at 1.0 A/g. Significantly, the supercapacitor performance of these porous hollow carbon nanofibers is also superior to that of many previously reported carbon materials, which proved them to be worthy candidates for high-performance electrode materials.
研究领域:
材料科学
·
电化学
·
纳米技术
·
能源存储
✓ 已验证
产品关联
DOI
PubMed
高影响因子
APPLIED SURFACE SCIENCE
·
2022
·
IF 7.392
Yi Wen,Zheng Huang,Min Zhao,Longshan Zhao
The discharge of industrial heavy metal wastewater not only leads to environmental pollution, but also harms human health, so it is imperative to control heavy metal pollution. In the current work, a sequence of anatase/brookite TiO 2 @COF with different mass ratios, bi-phase TiO 2 and bare COF were successfully synthesized by simple hydrothermal synthesis. The photocatalytic activity of the prepared catalysts was assessed by reducing Cr(Ⅵ) in model pollutant (K 2 Cr 2 O 7 ). Under the condition of pH = 3, the Cr(Ⅵ) reduction rate of TiO 2 @COF-4 was as high as 99.19% in 30 min. The photocatalytic activity of TiO 2 @COF-4 remained stable in four consecutive cycles, suggesting that it has a potential application prospect for the removal of Cr(Ⅵ) in the actual environment. The morphology and structure of photocatalysts were observed by different techniques (SEM/EDS, HRTEM, BET analysis, XRD, FTIR and XPS). The specific reasons for the enhancement of photocatalytic performance of materials were explored by different methods (PL, UV–vis DRS, Mott-Schottky plots, I-T curves and EIS). Finally, we concluded that the photocatalytic system of TiO 2 @COF-4 may follow the typical direct Z- scheme mechanism. This work provides an effective solution for the water treatment of heavy metal pollution.
研究领域:
环境科学
·
材料科学
·
化学工程
·
纳米技术
✓ 已验证
产品关联
DOI
高影响因子
Materials Research Express
·
2021
·Vol. 8
·期 3
·035009
·
IF 1.62
Yipeng Wang,Yunzhen Jia,Xuehui Sun,Peijian Sun,Song Yang,Quanping Yan,Bin Peng,Jizhao Guo,Xiaobing Zhang,Cong Nie
In order to reduce the hydrogen cyanide (HCN) release in cigarette mainstream smoke, a new type of porous corncob (PCC) material which was different from traditional corncob-based activated carbon was prepared by a two-step chemical reaction of carboxymethylation and cupric ion complexation. Fourier Transformation Infrared Spectroscopy (FTIR) showed that the carboxymethyl group had been introduced onto the corncob, the carboxymethyl content and the cupric ion loading amount were measured. The x-ray photoelectron spectrometer (XPS) results showed that the Cu content on the surface of PCC was much higher than that of the whole material. The scanning electron microscope (SEM) and nitrogen adsorption-desorption results suggested that PCC had a porous structure. With the increase of the amounts of chloroacetic acid and sodium hydroxide in carboxymethylation reaction and the concentration of cupric ion aqueous solution in complexing reaction, the BET surface areas and pore volumes increased, while the most probable pore sizes of PCCs were close to each other. Compared with the control cigarette, the addition of PCC could effectively remove the HCN release in cigarette mainstream smoke, and the highest reduction rates of HCN per total particulate matter (TPM) was 72.4 %.
研究领域:
材料科学
·
化学
·
烟草研究
✓ 已验证
产品关联
DOI
高影响因子
Catalysis Science & Technology
·
2023
·Vol. 13
·期 21
·6185-6197
·
IF 5
Hui Guo,Tingting Ge,Yuchao Li,Yuxia Li,Yanxia Zheng,Xinpeng Guo,Haofei Huang,Ming Wang,Cuncun Zuo
Organic solvent method was used to prepare the active component VPO, which was loaded on ball-milled γ-Al2O3 support. VPO/γ-Al2O3 catalysts were synthesized by in situ generation for the synthesis of acrylic acid (AA) by the aldol condensation of acetic acid (HAc) and formaldehyde (HCHO). The effects of the calcination temperature and the loading of the active component VPO on catalytic activity were systematically investigated. XRD, BET, SEM, CO2/NH3-TPD, FT-IR spectroscopy, and TG techniques were used to characterize the VPO/γ-Al2O3 catalysts. The results showed that the catalyst had the best crystal structure and acid–base activity center at a calcination temperature of 350 °C. The catalytic performance was evaluated using a fixed bed reactor. 60% VPO/γ-Al2O3 exhibited the highest reactivity, and the yield of AA was up to 51.5%. Response surface methodology (RAM) was used to optimize the reaction conditions for aldol condensation. The kinetic equation and reaction order of the aldol condensation reaction were determined using the VPO/γ-Al2O3 catalyst. It provides guidance for the in-depth study of aldol condensation reactions in the future.
研究领域:
催化
·
化学工程
·
材料科学
·
物理化学
✓ 已验证
产品关联
DOI
高影响因子
Polymer Chemistry
·
2012
·Vol. 4
·期 4
·1126-1131
·
IF 5.321
Yali Luo,Shoucun Zhang,Yunxiang Ma,Wei Wang,Bien Tan
Two hypercross-linked polymer networks have been synthesized by the self-condensation of bishydroxymethyl monomer, 1,4-benzenedimethanol (BDM), and monohydroxymethyl compound, benzyl alcohol (BA). This is different from the previous reports where multifunctional monomers or cross-linkers are crucial for constructing the porous polymer networks. N2 sorption isotherms for the polymers show that both materials are predominantly microporous with Brunauer–Emmett–Teller (BET) surface areas of 847 m2 g−1 for HCP–BDM and 742 m2 g−1 for HCP–BA. A network based on BA can also store a significant amount of CO2 (8.46 wt%) and H2 (0.97 wt%) at 1.0 bar, and at 273 K and 77 K respectively, despite its relatively modest surface area. Based on these results, this study opens up the possibility of synthesizing porous materials using monofunctional monomers.
研究领域:
材料科学
·
化学工程
·
聚合物化学
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2019
·
IF 4.084
Yang Liu,Haimiao Yu,Jiecheng Liu,Dezhen Chen
In this study, innovative Ni-based catalysts supported by five typical slag carriers (magnesium slag (MS), steel slag (SS), blast furnace slag (BFS), pyrite cinder (PyC) and calcium silicate slag (CSS)) were prepared by wet impregnation. With the prepared catalysts and Ni/γ-Al 2 O 3 catalyst, catalytic reforming of pyrolysis volatiles from pine sawdust for syngas production and tar removal was investigated. The catalysts were characterized by BET, XRD , SEM, TEM and Raman. The catalytic performances of the six catalysts were decreasing in the following order: Ni/MS > Ni/γ-Al 2 O 3 > Ni/SS > Ni/BFS > Ni/CSS > Ni/PyC. Ni/MS catalyst exhibited excellent catalytic reactivity as well as thermal stability in terms of tar conversion (95.19%), gas yield (1.46 Nm 3 /kg) and CO 2 capture ability (CO 2 yield of 0.5%). Both amorphous carbon and graphite-type carbon were formed on the catalysts after catalytic reforming and the D/G ratio (the relative intensity ratio of the D-band to the G-band) was positively correlated to the catalytic activity .
研究领域:
催化
·
化学工程
·
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2020
·
IF 10.652
Yuezhou Wei,Khalid A.M. Salih,Kamal Rabie,Khalid Z. Elwakeel,Yasser E. Zayed,Mohammed F. Hamza,Eric Guibal
Alginate-PEI beads are functionalized by phosphorylation and applied for the sorption of Nd(III) and Mo(VI). The successful grafting of phosphoryl groups (as tributyl phosphate derivative) is characterized by FTIR and XPS analysis, elemental analysis, titration (pH PZC ), TGA, BET and SEM-EDX analyses. The multi-functional characteristics of the sorbent (i.e., carboxylic, hydroxyl, amine and phosphate groups) contribute in the binding of metal ions having different physicochemical behaviors. The sorption of Nd(III) is strongly increased by phosphorylation, while for Mo(VI) the enhancement is rather limited. Optimum sorption occurs at pH 3–4: maximum sorption capacity reaches up to 1.46 mmol Nd(III) g −1 and 2.09 mmol Mo(VI) g −1 ; sorption isotherms are fitted by the Langmuir equation. The equilibrium is reached within 30–40 min and the kinetic profiles are simulated by the pseudo-first order rate equation. The coefficients of the effective diffusivity are close to the self-diffusivity of Nd(III) and Mo(VI) in water; as a confirmation of the limited impact of resistance to intraparticle diffusion in the kinetic control. The sorbent is selective for Nd(III) over Mo(VI) and other alkali-earth or base metals (at pH close to 2.5–3). Metals can be readily desorbed using 0.2 M HCl/0.5 M CaCl 2 as the eluent. The loss in sorption does not exceed 5% at the fifth cycle, while desorption remains complete. A series of treatments (including acidic leachate, cementation, precipitation, sorption and elution) is successfully applied for the recovery of rare earths from Egyptian ore; with enrichment in the oxalate precipitate of Nd(III), Gd(III), Sm(III) and Eu(III).
研究领域:
环境科学
·
材料科学
·
化学工程
·
分析化学
✓ 已验证
产品关联
DOI
高影响因子
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS
·
2021
·
IF 4.539
Ran Wang,Chong Cai,Di Wang,Zhiwei Liu,Lili Gao,Tifeng Jiao
In this work, a new type of self-assembled phytic acid-graphene oxide composite foam (PAGF) was prepared by hydrothermal method. In addition, Au nanoparticles (Au NPs) and Fe 3 O 4 particles were loaded onto PADF to obtain PAGF@Au&Fe 3 O 4 composite by a simple one-step method. The addition of graphene oxide (GO) can effectively prevent the agglomeration of Au NPs and weaken its surface passivation. The results of SEM, XRD, XPS and BET proved the successful preparation of the composite and its large specific surface area. Moreover, the synthesized PAGF@Au&Fe 3 O 4 composite showed good catalytic performance for p-nitrophenol (4-NP) and o-nitroaniline (2-NA) solutions with the rate constant (k) values of 0.0799 min −1 and 0.0546 min −1 , respectively. Due to the addition of Fe 3 O 4 , the composite exhibited good stability and recyclability, and maintained high catalytic efficiency after 8 cycles of catalytic process. The current work provides new ideas for developing novel graphene oxide-based composite materials and their catalytic degradation of organic pollutants.
研究领域:
材料科学
·
环境科学
·
纳米技术
·
催化
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF PHYSICS AND CHEMISTRY OF SOLIDS
·
2023
·
IF 4
Zishuang Guo,Menghui Deng,Haiwang Wang,Xiao Xiang,Chengang Zhang,Bingzhu Wang
In this paper, the microstructure evolution of polymeric carbon nitride was investigated and Au ions was used to improve its photocatalytic efficiency. Their structures were investigated by FT-IR, XPS, XRD , SEM and TEM. Their specific surface area and aperture distribution were measured by BET. Meanwhile, the energy band structure and electron-hole separation efficiency were analyzed by UV–Vis and PL spectroscopy. In addition, the photocatalytic performance of the photocatalysts was assessed by photocatalytic degradation of RhB and photocatalytic hydrogen evolution . The results showed that 600-PCN possessed the best photocatalytic performance, with a degradation rate of 46.92 % in 150 min. What's more, the degradation rate of RhB solution by 2 % Au/PCN reached 47.88 %, which was 2.17 times higher than that of 550-PCN (22.01 %). During the degradation process, h + oxidatively degrade RhB. The hydrogen production rate of 2 % Au/PCN was about 11.658 μmol/g/h, which was 41.23 times higher than that of 550-PCN (0.282 μmol/g/h).
研究领域:
材料科学
·
化学
·
催化
·
纳米技术
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
Food Bioscience
·
2024
·
IF 4.8
Huiting Fang,Huizhen Li,Yang Chen,Xiaoming Liu,Jianxin Zhao,Paul Ross,Catherine Stanton,Wei Chen,Bo Yang
There has been a rising interest in studying how Bifidobacterium breve can affect the immune system over the years. The aim of this study was to evaluate the effect of B. breve on the immune system and to explore the mechanism in a mouse model of cyclophosphamide (CTX)-induced immunosuppression. The results of the study showed that B. breve CCFM1310 significantly increased the thymus index (p < 0.05), promoting the secretion of immunoglobulins and the number of immune cells in the blood. Moreover, B. breve CCFM1310 could repair the spleen injury. It increased the mRNA expression level of T-bet (p < 0.05) and decreased the mRNA expression level of TGF-β and FOXP3 (p < 0.05). B. breve CCFM1310 alleviated oxidative stress by increasing enzymatic activities of SOD, CAT and T-AOC and reducing the concentration of MDA. Moreover, it repaired intestinal damage by increasing the number of goblet cells, upregulating mRNA expression of tight junction proteins, and promoting the production of short-chain fatty acids (SCFA). B. breve CCFM1310 could regulate the gut microbiota by increasing the relative abundance of Lactobacillus (p < 0.05) and decreasing the relative abudance of Lachnospiraceae NK4A136 group . Overall, our study suggests that B. breve CCFM1310 could enhance immunity in CTX-induced immunosuppressed mice by affecting immune responses, oxidative stress and gut microbiota.
研究领域:
免疫学
·
微生物学
·
药理学
✓ 已验证
产品关联
DOI
高影响因子
危险品化学品经营许可证（带存储）