ELECTROCHIMICA ACTA
·
2016
·
IF 4.803
Zhen Liu,Jingkun Xu,Ruirui Yue,Taotao Yang,Lei Gao
This paper demonstrates that Au–PEDOT/reduced graphene oxide nanocomposite (Au–PEDOT/rGO) can be rapidly synthesized through a facile, cost-effective one-pot method with chloroauric acid as the oxidant and NaBH 4 as the reductant successively. The morphology, composition and structure of the obtained composites were confirmed by SEM, TEM, XRD, Raman and XPS characterizations. The Au–PEDOT/rGO modified glassy carbon electrode (GCE) showed significantly improved charge transfer efficiency and high electrocatalytic activity toward caffeic acid (CA) oxidation as compared to bare GCE and Au-PEDOT modified electrode. Under optimized conditions, the Au–PEDOT/rGO constructed sensors exhibited a wide linear range of 0.01–46 μM with the correlation coefficient of 0.9926 and a detection limit as low as 0.004 μM for the detection of CA. To validate its possible application, the present sensor was also illustrated with satisfactory anti-interference performance, high reproducibility and sensitivity for the determination of CA in red wine sample. The prepared Au–PEDOT/rGO nanocomposite is a promising electrode material for the determination of CA in red wines or other CA-containing food and beverage.
✓ 已验证
产品关联
DOI
高影响因子
PARTICLE & PARTICLE SYSTEMS CHARACTERIZATION
·
2016
·Vol. 34
·期 3
·1600233
·
IF 4.367
Yanzhou Jiang,Yan Gu,Guangdi Nie,Maoqiang Chi,Zezhou Yang,Ce Wang,Yen Wei,Xiaofeng Lu
In this paper, a novel strategy for the fabrication of reduced graphene oxide (rGO)/Cu 8 S 5 /polypyrrole (PPy) composite nanosheets with Cu 8 S 5 nanoparticles and PPy layer anchored on the surface of rGO as peroxidase-like nanocatalyst is reported. During the synthesis, graphene oxide (GO)/CuO composite nanosheets are prepared first and used as templates, then the sulfuration of CuO and polymerization of pyrrole are accompanied with the reduction of GO, resulting in ternary rGO/Cu 8 S 5 /PPy composite nanosheets. The synthesized Cu 8 S 5 nanoparticles with a diameter in the range from tens to hundreds of nanometers are dispersed within PPy decorated rGO nanosheets. The resultant ternary rGO/Cu 8 S 5 /PPy composite nanosheets exhibit a higher peroxidase-like catalytic activity toward the oxidation of 3,3′,5,5′-tetramethylbenzidine in the presence of H 2 O 2 than GO/CuO and rGO/CuS composite nanosheets, revealing a synergistic effect on their activity. The as-prepared rGO/Cu 8 S 5 /PPy platform provides a simple colorimetric approach for the detection of H 2 O 2 and phenol with a high sensitivity. This work offers a new way for the fabrication of rGO-based nanocomposite with superior enzyme-like activity, which displays great potential applications in biocatalysis and environmental monitoring.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MATERIALS CHEMISTRY
·
2012
·Vol. 22
·期 41
·21998-22004
·
IF 5.968
Gong Cheng,Yan-Lin Liu,Zhi-Gang Wang,Ji-Lin Zhang,De-Hui Sun,Jia-Zuan Ni
The graphene oxide (GO)–Fe3O4 and the reduced graphene oxide (rGO)–Fe3O4 composites with good water dispersibility, high affinity and rapid magnetic response have been prepared via a facile grafting method. They can be used for the effective immobilization of proteins and the enrichment of peptides, respectively. By taking advantage of the high loading capacity and the abundant hydrophilic groups of the GO–Fe3O4 composites, they can be applied to immobilize proteins. The amount of loading of protein (BSA) on GO–Fe3O4 is as high as 294.54 mg g−1. The rGO–Fe3O4 composites can be used to enrich the low-concentration peptides conveniently due to their high surface areas, special structures and strong magnetism. Nineteen target peptides with the sequence coverage of 21% can be enriched and detected from the highly diluted digest of BSA (5 fmol μL−1). These results reveal that the prepared GO/rGO–Fe3O4 composites have potential application as a carrier for biomolecule immobilization, enrichment, and separation.
✓ 已验证
产品关联
DOI
高影响因子
Journal of Energy Storage
·
2024
·
IF 8.9
Yuting He,Yongjin Zou,Cuili Xiang,Fen Xu,Yongpeng Xia,Yulian Chen,Shunxiang Wang,Zhicong Hu,Sijia Hao,Lixian Sun
Shape-stabilized composite phase change materials (CPCMs) with high photothermal conversion efficiency, high thermal storage capacity, and excellent thermal conductivity hold immense potential for diverse applications and market growth. This study employed a one-step substitution reaction followed by a thermal reduction technique to successfully affix Ni and Cu nanoparticles onto reduced graphene oxide (rGO) nanosheets , which were subsequently integrated into a nickel foam (NF) matrix. This process resulted in the fabrication of an NF/Ni-Cu@rGO porous carrier, facilitating the adsorption of polyethylene glycol (PEG) and the formation of CPCMs. Introducing Ni-Cu@rGO into the NF matrix enhanced the carrier framework, enabling improved PEG loading and leakage prevention. The hybridization of Ni-Cu@rGO effectively bolstered the interaction between the carrier framework and the phase change material (PCM), resulting in enhanced phase change performance. CPCMs prepared from the NF/Ni-Cu@rGO framework exhibited superior shape stability, higher thermal storage density, and enhanced recyclability than pure PCMs. Optimized CPCMs displayed melting and crystallization enthalpies of 121.13 J·g −1 and 113.44 J·g −1 , respectively. The thermal conductivity of NF/Ni-Cu@rGO/PEG CPCMs significantly improved to 0.4780 W·m −1 K −1 , representing a remarkable 315 % increase over that of PEG alone. Furthermore, the NF/Ni-Cu@rGO/PEG composite demonstrated outstanding photothermal conversion efficiency, thermal cycling stability, and exceptional shape stability. These findings offer promising prospects for its application across various fields.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF ELECTRONIC MATERIALS
·
2025
·
IF 2.5
Tan Shangrong,Yao Zhuo,Huang Hong,Liu Zechen,Guo Shiqi,Zhao Xinyun
Electrochemical supercapacitors, given their high power density and excellent cycling stability, have broad applications from electronic devices to electric vehicles. In this study, we have developed novel nanocomposites to serve as electrodes of high-performance supercapacitors. The nanocomposites, referred to as Cu/MnX x (X = O, S, C)-rGO (rGO: reduced graphene oxide), were fabricated through direct oxidation, sulfidation, and carbonization at elevated temperatures from their metal–organic framework origin, i.e., Cu/Mn-BTC-rGO (BTC: benzene–1,3,5-tricarboxylic acid). This process is cost-effective and scalable, and can be fine-tuned to achieve a variety of nanocomposites with the desired chemistry and structural characteristics. The carbonized product, Cu/MnC x -rGO, is made up of nanoparticles of MnO and copper in close contact supported on rGO nanosheets via strong coupling. This material demonstrates excellent charge storage, rate capability, and cycling stability, i.e., high specific capacitance of 718.6 F g −1 at a current density of 1 A g −1 , with 92.6% capacitance retention after 1000 cycles. The hierarchical 3D structured Cu/MnC x -rGO nanocomposite has unique chemistry, high surface area, and high electrical conductivity, and hence ensures rapid ion and electron transport beneficial to both pseudocapacitive and double-layer capacitive performance.
✓ 已验证
产品关联
DOI
高影响因子
MICROCHEMICAL JOURNAL
·
2024
·
IF 4.9
Xixiang Xie,Junxiang Zeng,Xianli Lan,Xiyu Liu,Jian He,Pan Wu,Yan Huang,Mengqi Chen,Meiyan Wu,Guiyin Li,Liang Shi,Yong Huang
As cholesterol is very intimately linked to the development of many types of cardiovascular diseases, clinical medicine must have a straightforward and precise method for determining total serum cholesterol (TC). Nowadays, enzymatic methods are routinely used in laboratories for the determination of TC, using cholesterol oxidase and esterase reagents for quantitative analysis on fully automated instruments. In this work, an electrochemical biosensor was developed for highly sensitive detection of cholesterol by modified modification of screen-printed carbon electrode (SPCE) and reduction of peroxidase-mimetic catalytic activity of reduced graphene oxide-hemin (RGO-hemin) nano-enzyme. The hydrolysis of cholesterol produced H 2 O 2 when it was subjected to the actions of cholesterol oxidase (CHOD), cholesterol esterase (CHER), and RGO-hemin. In the presence of H 2 O 2 , ferrocene-tyramine (Fc-Tyr) triggers catalytic deposition amplification effect on the SPCE surface, a great deal of electroactive ferrocene marker accumulates on the electrode surface, and Fc-Tyr is measured by an electrochemical workstation. The redox electrical signal detects the concentration of cholesterol in the sample. The biosensor had an operating range of 0.1∼5 mg/mL and a sensitivity of 24.43 μg/mL with acceptable specificity. The electrochemical cholesterol biosensor sensitively captured cholesterol signals in a complex body fluid environment and showed results consistent with clinical trials, with 96.63∼107.32 % recovery and 0.78∼5.28 % relative standard deviation (RSD). Therefore, there is a significant chance that the cholesterol biosensor by the institute will be used in clinical settings to detect serum cholesterol.
✓ 已验证
产品关联
DOI
高影响因子
International Journal of Electrochemical Science
·
2024
·
IF 1.3
Ziming Xu,Junjie You,Zhuotong Yu,Chuanqing Du,Yourong Wang,Siqing Cheng
Tin dioxide (SnO 2 ) have been considered to be a promising anode material for high performance lithium-ion batteries (LIBs) due to its high lithium storage capacity of as high as 1494 mAh g −1 , which has been impeded greatly due to its large volumetric expansion and low conductivity. Thus, the simple but effective approach for the fabrication of SnO 2 -based material is ever-urgent. To this end, the mesoporous SnO 2 @N-rGO nanocomposites were designed and fabricated by a simple and scalable electrostatic self-assembly method and investigated electrochemically as anode for LIBs. The results show that the as-obtained mesoporous SnO 2 @N-rGO nanocomposites exhibit an excellent cycling stability and outstanding rate capability after an initial activation due to the formation of SEI layer on the surface, which are mainly ascribed to the synergistic effect of nano-SnO 2 , high conductive N-doped rGO matrix network and rich mesopores. Therefore, this work offers an ingenious strategy to design and fabricate the SnO 2 -based anode material for high performance lithium-ion batteries.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2024
·
IF 5.8
Wenyan Huang,Jiahao Hu,Yeqi Zhu,Jiahua Zhan,Rongdan Lei,Yuchen Sun,Kaiqi Chen,Siqi Lan,Rongqian Yao
As contemporary aerospace and radar-detecting technologies evolve, load bearing-microwave absorption integration of thermal protection materials for complex environment requirements are urgent. Well known for low density, good high-temperature resistance and superior tunable dielectric properties, polymer-derived ceramics (PDCs) promisingly meet most needs of high-performance aircraft thermal protection system (TPS). Aimed at promoting practical application, we integrate in-situ formed Ni 2 Si into lightweight SiC(rGO) nanocomposite PDCs via re-pyrolyzing coassembled nano-Ni/SiC(rGO) p /polycarbosilane-vinyltriethoxysilane-graphene oxide (PVG) blends to enhance their mechanical and electromagnetic wave (EMW) absorbing performances. Size effect on phase transition of Ni into Ni 2 Si (as brazing bonding agents) accompanied by volumetric expansion, ingeniously eliminates stretching stress from PVG precursor inward shrinkage for compact framework during re-pyrolysis. In-situ generated Ni/Ni 2 Si/C core-shell nanostructure (similar to nodular cast iron) has good chemical compatibility with β-SiC/SiO x C y /C free (rGO), thereby enables composites improved compactness and toughness. More interestingly, heterogeneous interfaces/defects among Ni, Ni 2 Si, carbon shell, β-SiC and SiO x C y /C free (rGO) matrix, effectively facilitate interfacial/dipole polarization for robust EMW absorption, and lightweight SiC(rGO, Ni 2 Si) Ni=4% nanocomposite PDCs exhibit outstanding fracture toughness of 6.56 MPa·m 1/2 and high compressive strength of 119.25 MPa. Such composite with structure-function integration maintain stable under butane blowtorch at ∼1300 °C, shedding light on a new route to mass-manufacture aerospace vehicle components.
✓ 已验证
产品关联
DOI
高影响因子
MICROCHIMICA ACTA
·
2024
·Vol. 191
·期 6
·1-10
·
IF 5.3
Zhong Yujun,Li Zhiyang,Zhang Anlin,Peng Yuqing,Zhou Hao,Wang Bin,Xie Lianwu,Guo Yaping
A novel electrochemical sensor, MIP/Cu-MOF/rGO/AuNPs/GCE, was developed by depositing gold nanoparticles, coating Cu-MOF/GO on the surface of glassy carbon electrode (GCE) before electroreducing graphene oxide (GO) to rGO and covering molecularly imprinted membrane by electropolymerization for highly sensitive detection of electroneutral organophosphorus pesticide residues in agricultural product. Cyclic voltammetry, differential pulse voltametry, scanning electron microscopy, energy-dispersive spectroscopy, and atomic force microscopy were used to characterize the imprinted sensor. Several key factors such as chitosan concentration, suspension volume, pH of polymerization solution, and polymerization scanning rate during preparation of the imprinted sensor were optimized in detail. When electroneutral phosmet was used as a template, the linear range of MIP/Cu-MOF/rGO/AuNPs/GCE for detecting phosmet was 1.00 × 10 −14 –5.00 × 10 −7 mol/L with the limit of detection of 7.20 × 10 −15 mol/L at working potentials of − 0.2 to 0.6 V. The selectivity, reproducibility, and repeatability of MIP/Cu-MOF/rGO/AuNPs/GCE were all acceptable. The recoveries of this method for determining phosmet in real samples ranged from 94.2 to 106.5%. The MIP/Cu-MOF/rGO/AuNPs/GCE sensor could be applied to detect electroneutral pesticide residues in organisms and agricultural products. Graphical Abstract
✓ 已验证
产品关联
DOI
PubMed
高影响因子
MICROCHIMICA ACTA
·
2024
·Vol. 191
·期 11
·1-17
·
IF 5.3
Liang Jintao,Liang Jianlu,Xiao Xinkai,Guo Fei,Zhan Yulian,Zhou Xueqing,Zhou Zhide,Li Guiyin
A sandwich-type electrochemical aptasensor for ultrasensitive detection of glypican-3 (GPC3) was constructed using GPC3 aptamer (GPC3 Apt ) labelled reduced graphene oxide-cerium oxide-gold nanoparticles (RGO-CeO 2 -Au NPs) as the signal probe and the same GPC3 Apt as the capture probe. The electrochemical redox properties of CeO 2 (Ce 3+ /Ce 4+ ) in the RGO-CeO 2 -Au NPs indicate the electrochemical signals. When the target GPC3 was present, an “aptamer-protein-aptamer” sandwich structure was formed on the sensing interface due to the specific binding between the protein and aptamers, resulting in an increased electrochemical redox signal detected by differential pulse voltammetry (DPV) technique. Under optimal conditions, the established aptasensor exhibited a logarithmic linear relationship between the current response and GPC3 concentration in the range 0.001–100.0 ng/mL, with a minimum detection limit of 0.74 pg/mL. Using the spike-recovery tests for measurement of the human serum samples, the recovery was from 99.26 to 114.01%, and the RSD range was 3.04 to 5.34%. Furthermore, the sandwich-type electrochemical aptasensor exhibited excellent performance characteristics such as good stability, high specificity, and high sensitivity, demonstrating effective detection of GPC3 in human serum samples and can be used as a clinical detection tool for GPC3. Graphical Abstract
✓ 已验证
产品关联
DOI
PubMed
高影响因子
ACS Applied Materials & Interfaces
·
2024
·
IF 8.3
Zhen Qin,Ziwen Wang,Dan Li,Yuhuan Lv,Biao Zhao,Kai Pan
The assembly of two-dimensional (2D) nanomaterials into a three-dimensional (3D) aerogel can effectively prevent the problem of restacking. Here, nanofiber-reinforced MXene/reduced graphene oxide (rGO) conductive aerogel is prepared via the hydrothermal reduction of GO using pyrrole and in situ composite with MXene. Combined with low-content 2D conductive nanosheets (MXene and rGO) as “brick”, conductive polypyrrole as “mortar”, and one-dimensional (1D) nanofiber as “rebar”, a strong interfacial cross-linking of MXene and rGO nanosheets is realized through covalent and noncovalent bonds to synergistically improve its mechanical performance. Based on the prepared MXene/rGO aerogel, a high-performance piezoresistive sensor with a sensitivity of up to 20.80 kPa–1 in a wide pressure range of 15.6 kPa is obtained, and it can withstand more than 5000 cyclic compressions. Besides, the sensor shows a stable output and can be applied to monitor various human motion signals. In addition, an all-solid-state supercapacitor electrode is also fabricated, which shows a high area-specific capacitance of up to 274 mF/cm2 at a current density of 1 mA/cm2.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2022
·
IF 16.744
Yumeng Wang,Peng Zhang,Lai Lyu,Weixiang Liao,Chun Hu
Natural organic matter (NOM) has diverse negative impacts on water purification , however, preventing them occurrence very difficult. Herein, humic acid (10 mg/L), as the main component of NOM, is completely destructed within 120 min in the Fe 0 -Fe y C z /Fe x -GZIF-8-rGO air-saturated aqueous suspension without additional energy input, while its mineralization is followed by three kinetic constants within 480 min. During the process, HA was first complexed with Fe 0 -Fe y C z /Fe x -GZIF-8-rGO by π-π interaction and H-bonding interaction and cleaved to aromatic compounds and then to alkanes and alcohols with some small acids before 120 min. The electron paramagnetic resonance (EPR) analysis and density functional theory (DFT) calculations confirmed that a strongly polarized alkane-alcohol complex was formed after 150 min with an electron-rich hydroxyl group area in alcohol and an electron-poor alkane area. Moreover, the more electrons of alkane in the complex are delocalized and trapped by O 2 , with the adsorption of the alkane-alcohol complex on the catalyst surface based on the analyses of both electrochemical impedance spectroscopy (EIS) and chronoamperometry, greatly promoting the surface cleavage and hydrolytic process of alkane in the complex and producing more • OH for pollutant degradation than it does from the HA surface complex, which results in the highest mineralization rate in the period of 150–390 min. Our findings demonstrated that the current system is very promising for complex mixture-containing water purification without additional energy.
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）