本产品由9 kDa~180 kDa范围的10个蛋白条带组成 (9 kDa、16 kDa、25 kDa、30 kDa、38 kDa、 50 kDa、64 kDa、85 kDa、125 kDa、180 kDa)。由低到高的分子量范围可监测电泳过程中的蛋白分离情况、判断目标蛋白的分子量,并且可以监测 Western Blot 实验中的转膜效率。9 kDa、64 kDa 两条带结合有绿色或红色染料,更便于实时观察电泳进程、判断蛋白分子量。
使用说明
1、加样前在室温放置数分钟,解冻后,轻轻摇匀,以确保溶液混合均匀;
2、取用适量体积加样于凝胶孔,推荐用量为2~5 μL/孔,可根据具体情况适当增减;
3、取用结束,盖上管盖,放回4℃或-20℃。
注:以上样5 μL为例,每个条带蛋白含量约为1 μg~3 μg。
注意事项
1、本品已包含上样缓冲液,直接使用,不可加热煮沸;
2、为避免反复冻融及污染,可将本产品分装后,-20℃保存;
3、预染蛋白质分子量标准仅用于分子量的近似参考,批次间差异约为5%;
4、在低浓度凝胶中,低分子量条带将会与前沿共迁移而无法分出;
5、在不同凝胶和缓冲液系统中,预染蛋白质的迁移率会有所差别,可用非预染蛋白质分子量标准进行校正,并按校正后的结果正常使用;
6、蛋白分子量标准可能会与抗体发生非特异性结合,可以降低抗体浓度、减少孵育时长,以及减小蛋白分子量标准上样量来进行优化;
7、为了您的安全和健康,请穿实验服并戴一次性手套操作;
8、本产品仅限科研使用。
This product consists of 10 protein bands ranging from 9 kDa to 180 kDa (9 kDa, 16 kDa, 25 kDa, 30 kDa, 38 kDa, 50 kDa, 64 kDa, 85 kDa, 125 kDa, 180 kDa). The low-to-high molecular weight range allows monitoring of protein separation during electrophoresis, determination of target protein molecular weights, and assessment of transfer efficiency in Western Blot experiments. The 9 kDa and 64 kDa bands are conjugated with green or red dyes, facilitating real-time observation of the electrophoresis process and determination of protein molecular weights.
Usage method:
1. Place at room temperature for several minutes before loading. After thawing, gently shake to ensure the solution is thoroughly mixed.
2. Load an appropriate volume into the gel wells. The recommended volume is 2–5 μL per well, which can be adjusted according to specific conditions.
3. After use, cap the tube and return it to 4°C or -20°C.
Note: Taking a 5 μL loading volume as an example, the protein content of each band is approximately 1–3 μg.
Precautions
1. This product already contains loading buffer. Use it directly; do not heat or boil.
2. To avoid repeated freeze-thaw cycles and contamination, aliquot the product and store at -20°C.
3. The prestained protein molecular weight standard is intended only for approximate molecular weight reference; batch-to-batch variation is approximately 5%.
4. In low-concentration gels, low molecular weight bands may co-migrate with the dye front and cannot be resolved.
5. The migration of prestained proteins may vary in different gel and buffer systems. Calibration using a non-prestained protein molecular weight standard is recommended, and the product can be used normally after calibration.
6. The protein molecular weight standard may exhibit non‑specific binding to antibodies. This can be optimized by reducing antibody concentration, shortening incubation time, and decreasing the loading amount of the protein molecular weight standard.
7. For your safety and health, please wear a lab coat and disposable gloves during handling.
8. This product is for research use only.