富马酸检测试剂盒

货号: F486219
有货
级别和纯度: 96T
★
规格
库存
价格
数量
1kit
F486219-1kit
现货 Stock Image
¥3,499.90
请输入您要添加的产品数量

概述

本试剂盒仅供研究使用。

使用目的: 

本试剂盒用于测定样本中延胡索酸(fumric cid)的含量。 

实验原理: 

本试剂盒应用酶联免疫竞争法测定标本中延胡索酸(fumric cid)水平。用纯化的延胡索酸(fumric cid)抗体包被微孔板,制成固相抗体,往包被单抗的微孔中加入延胡索酸(fumric cid),和 HRP 标记的延胡索酸(fumric cid)抗原,使它们竞争结合,经过彻底洗涤后加底物TMB 显色。样本颜色的深浅和样品中的延胡索酸(fumric cid)的含量呈负相关。用酶标仪在 450nm 波长下测定吸光度(OD 值),通过标准曲线计算样品中延胡索酸(fumric cid)的含量。

试剂盒组成:
1. 30 倍浓缩洗涤液 20ml×1 瓶
2. 酶标试剂 6ml×1 瓶
3. 酶标包被板 12 孔×8 条
4. 显色剂 A 液 6ml×1 瓶
5. 显色剂 B 液 6ml×1 瓶
6. 终止液 6ml×1/瓶
7. 样品稀释液 6ml×1/瓶
8. 标准品 S1(200ng/L) 0.5ml×1 瓶
标准品 S2(100ng/L) 0.5ml×1 瓶
标准品 S3(50ng/L) 0.5ml×1 瓶
标准品 S4(25ng/L ) 0.5ml×1 瓶
标准品 S5(12.5ng/L) 0.5ml×1 瓶
9.  封板膜 2 张 

标本要求 :

1.标本处理:(1)水样 采集后经 -20℃反复冻融三次,再经玻璃纤维过滤后,备查 (2)组织 样品用丁醇:甲醇:水(5:25:70 V:V:V)抽提,或按相 关文献提取进行,提取后应尽快进行实验。若不能马上进行试验, 可将标本放于-20℃保存,备查 

2.不能检测含 NaN3 的样品,因 NaN3 抑制辣根过氧化物酶的(HRP)活性。 

操作步骤:

1. 加样:分别设标准孔、空白孔(空白对照孔不加样品及酶标试剂,其余各步操作相同)、 待测样品孔。在酶标包被板上标准孔中加 50 微升,待测样品孔中先加样品稀释液 40μl, 然后再加待测样品 10μl(样品最终稀释度为 5 倍)。加样将样品加于酶标板孔底部,尽 量不触及孔壁,轻轻晃动混匀。

2. 加酶:每孔加入酶标试剂 50μl,空白孔除外。 

3. 温育:用封板膜封板后置 37℃温育 60 分钟。 

4. 配液:将 30 倍浓缩洗涤液用蒸馏水 30 倍稀释后备用 

5. 洗涤:小心揭掉封板膜,弃去液体,甩干,每孔加满洗涤液,静置 30 秒后弃去,如此 重复 5 次,拍干。

6. 显色:每孔先加入显色剂 A50μl,再加入显色剂 B50μl,轻轻震荡混匀,37℃避光显色 15 分钟. 

7. 终止:每孔加终止液 50μl,终止反应(此时蓝色立转黄色)。 

8. 测定:以空白孔调零,450nm 波长依序测量各孔的吸光度(OD 值)。 测定应在加终止 液后 15 分钟以内进行。  

计算:

以标准物的浓度为横坐标,OD 值为纵坐标,在坐标纸上绘出标准曲线,根据样品的 OD 值由标准曲线查出相应的浓度;再乘以稀释倍数;或用标准物的浓度与 OD 值计算出标 准曲线的直线回归方程式,将样品的 OD 值代入方程式,计算出样品浓度,再乘以稀释倍数, 即为样品的实际浓度。

注意事项:

1.试剂盒从冷藏环境中取出应在室温平衡 1 小时后方可使用,酶标包被板开封后如未用完, 板条应装入密封袋中保存。 

2.浓洗涤液可能会有结晶析出,稀释时可在水浴中加温助溶,洗涤时不影响结果。 

3.各步加样均应使用加样器,并经常校对其准确性,以避免试验误差。一次加样时间最好 控制在 5 分钟内,如标本数量多,推荐使用排枪加样。 

4. 请每次测定的同时做标准曲线,最好做复孔。如标本中待测物质含量过高(样本 OD 值 大于标准品孔第一孔的 OD 值),请先用样品稀释液稀释一定倍数(n 倍)后再测定,计 算时请最后乘以总稀释倍数(×n×5)。 

5. 封板膜只限一次性使用,以避免交叉污染。

6.底物请避光保存。 

7.严格按照说明书的操作进行,试验结果判定必须以酶标仪读数为准. 

8.所有样品,洗涤液和各种废弃物都应按传染物处理。 

9.本试剂不同批号组分不得混用。  

检测范围:

4ng/L -250ng/L 

保存条件及有效期:

1.试剂盒保存:2-8℃。 

2.有效期:6 个月

This reagent kit is for research purposes only.
Purpose of use:
This reagent kit is used to determine the content of fumaric acid in samples.
Experimental principle:
This kit applies enzyme-linked immunosorbent assay to determine the level of fumaric acid (fumric cid) in the sample. Purified fumaric acid (fumric acid) antibody was coated on a microplate to prepare a solid-phase antibody. fumric acid was added to the microplate of the coated monoclonal antibody and competed with HRP labeled fumric acid antigen to bind. After thorough washing, the substrate TMB was added for color development. The depth of sample color is negatively correlated with the content of fumaric acid in the sample. Measure the absorbance (OD value) at a wavelength of 450nm using an enzyme-linked immunosorbent assay (ELISA) reader, and calculate the content of fumaric acid (fumric cid) in the sample through a standard curve.
Kit composition:
1. 20ml of 30 times concentrated washing solution × 1 bottle
2. Enzyme labeling reagent 6ml × 1 bottle
3. Enzyme coated plate with 12 wells × 8 articles
4. Color reagent A solution 6ml × 1 bottle
5. Color reagent B solution 6ml × 1 bottle
6. Termination liquid 6ml × 1/bottle
7. Sample diluent 6ml × 1/bottle
8. Standard S1 (200ng/L) 0.5ml × 1 bottle
Standard S2 (100ng/L) 0.5ml × 1 bottle
Standard S3 (50ng/L) 0.5ml × 1 bottle
Standard S4 (25ng/L) 0.5ml × 1 bottle
Standard S5 (12.5ng/L) 0.5ml × 1 bottle
9. Two sealing films

Specimen requirements:
1. Specimen processing: (1) After collecting the water sample, it is repeatedly freeze-thawed at -20 ℃ three times, and then filtered with glass fiber for future reference. (2) The tissue sample is extracted using butanol: methanol: water (5:25:70 V: V: V), or extracted according to relevant literature. The experiment should be conducted as soon as possible after extraction. If the experiment cannot be conducted immediately, the specimen can be stored at -20 ℃ for future reference
2. Samples containing NaN3 cannot be detected as NaN3 inhibits the activity of horseradish peroxidase (HRP).
Operation steps:
1. Sample addition: Set up standard wells, blank wells (blank control wells do not include samples and enzyme-linked immunosorbent assay reagents, the other steps are the same), and sample wells to be tested. Add 50 microliters to the standard well on the enzyme-linked immunosorbent assay (ELISA) plate, and first add 40 diluents to the sample well to be tested μ l. Then add 10 more samples to be tested μ L (The final dilution of the sample is 5 times). Add the sample to the bottom of the enzyme-linked immunosorbent assay (ELISA) plate well, avoiding touching the well wall as much as possible. Gently shake and mix well.
2. Enzyme addition: Add 50 enzyme labeled reagents to each well μ l. Excluding blank holes.
3. Warm incubation: Seal the plate with a sealing film and incubate at 37 ℃ for 60 minutes.
4. Solution preparation: Dilute 30 times the concentrated washing solution with distilled water and set aside for later use
5. Washing: Carefully remove the sealing film, discard the liquid, shake dry, fill each well with washing solution, let it stand for 30 seconds, then discard. Repeat this process 5 times and pat dry.
6. Color development: Add color development agent A50 to each well first μ l. Add color developer B50 again μ l. Gently shake and mix well, and develop color at 37 ℃ in the dark for 15 minutes
7. Termination: Add 50% termination fluid to each hole μ l. Terminate the reaction (at this point, the blue color immediately turns yellow).
8. Measurement: Zero the blank hole and sequentially measure the absorbance (OD value) of each hole at a wavelength of 450nm. The measurement should be conducted within 15 minutes after adding the termination solution.

Calculation:
Draw a standard curve on a coordinate paper with the concentration of the standard substance as the x-axis and the OD value as the y-axis. Based on the OD value of the sample, determine the corresponding concentration from the standard curve; Multiply it by the dilution factor; Alternatively, a linear regression equation can be used to calculate the standard curve using the concentration and OD value of the standard substance. The OD value of the sample can be substituted into the equation to calculate the sample concentration, which is then multiplied by the dilution factor to obtain the actual concentration of the sample.
Notes:
1. The kit shall be used after being taken out of the cold storage environment and balanced at room temperature for 1 hour. If the enzyme coated plate is not used up after opening, the Flat noodles shall be stored in a sealed bag.
2. Concentrated detergent may precipitate crystals. When diluted, it can be heated in a water bath to aid in dissolution. Washing does not affect the results.
3. A sampler should be used for each step of sample addition, and its accuracy should be regularly calibrated to avoid experimental errors. It is best to control the sample addition time within 5 minutes. If there are a large number of specimens, it is recommended to use a firing gun for sample addition.
4. Please make a standard curve at the same time as each measurement, preferably with a re hole. If the content of the substance to be tested in the sample is too high (the OD value of the sample is greater than the OD value of the first well of the standard well), please dilute the sample diluent by a certain multiple (n times) before measurement. When calculating, please multiply the total dilution multiple by the final factor( × N × 5) .
5. The sealing film is only for one-time use to avoid cross contamination.
6. Please store the substrate in dark.
7. Strictly follow the instructions and determine the test results based on the reading of the enzyme-linked immunosorbent assay (ELISA) reader
8. All samples, washing liquids, and various waste should be treated as infectious substances.
9. The components of this reagent with different batch numbers shall not be mixed.
Detection range:
4ng/L-250ng/L
Storage conditions and validity period:
1. Kit storage: 2-8 ℃.
2. Validity period: 6 months

规格

规格或纯度
96T
英文名称
Fumarate Assay Kit
储存与运输
储存条件
2-8°C储存
运输条件
低温运输

高级数据

质检证书(CoA,COO,BSE/TSE 和分析图谱)
C of A & Other Certificates(BSE/TSE, COO):
输入批号以搜索分析图谱:

通过匹配包装上的批号来查找并下载产品的 COA,每批产品都进行了严格的验证,您可放心使用!

找到6个结果

批号(Lot Number) 证书类型 货号
B2625873B2625873 分析证书 F486219
L2530025L2530025 分析证书 F486219
I2508055I2508055 分析证书 F486219
H2423006H2423006 分析证书 F486219
C2411106C2411106 分析证书 F486219
L2326251L2326251 分析证书 F486219
技术文档和文章
溶液计算器

常见问题

本产品应如何储存?
请于2–8 °C条件下保存。需冷藏保存以维持规定的有效期。
本产品如何运输?
本产品采用湿冰冷藏运输。收货后请立即拆包,并按上述储存条件保存。
如何获取批次专用COA?
每个订单都会随附分析证书(COA),您也可以从账户订单历史中下载。如需订购前的COA,请联系您的客户代表,或使用PDP上的"申请COA"按钮——我们将提供代表性批次的COA。