CERAMICS INTERNATIONAL
·
2021
·
IF 4.527
Ying Zhang,Xuhuan Zhao,Shiqi Fu,Xiulong Lv,Qian He,Yingxin Li,Fangying Ji,Xuan Xu
An Ag/TiO 2 coating was deposited onto glazed ceramic tiles by a sol-gel and spraying method at high temperatures. The coating was characterized by X-ray diffraction, scanning electron microscopy, and atomic force microscopy . The results showed that silver was present in rutile-TiO 2 , and the temperature did not change the phase composition of the samples. The Ag/TiO 2 coating had a higher roughness than the TiO 2 coating. The tape test (D 3359–08) showed that the coatings prepared at 950 °C and 1000 °C had good adhesion to the ceramic tile substrate. The antibacterial activity of the coating was tested by photocatalytic sterilization experiments. The results showed that the Ag/TiO 2 coating had a higher antibacterial activity than the TiO 2 coating, and the sterilization efficiency of Escherichia coli, Staphylococcus aureus, Shigella , and Salmonella exceeded 99.655% under 2 h of visible light irradiation. This research provides a method to create Ag/TiO 2 coatings with good thermal resistance, adhesion, and antibacterial activity. This improves the low photocatalytic activity caused by the anatase-to-rutile transformation of TiO 2 at high temperatures and the poor adhesion at low temperatures.
研究领域:
材料科学
·
微生物学
✓ 已验证
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2015
·
IF 2.999
Rong Li,Yuefa Jia,Naijing Bu,Jun Wu,Qiang Zhen
Using home-made Fe 2 O 3 /TiO 2 nanopowders as raw material, Fe 2 O 3 /TiO 2 composite ceramic was fabricated in order to use as photocatalysts in practical water purification treatment. The effects of sintering temperature on its phase variation, physical properties and photocatalytic properties were investigated. With sintering temperature increases, the anatase TiO 2 transforms into rutile phase, and reacts with hematite Fe 2 O 3 to form pseudobrookite Fe 2 TiO 5 . Above 800 °C, only Fe 2 TiO 5 and rutile TiO 2 were observed. Correspondingly, the porosity and the photocatalytic activity of Fe 2 O 3 /TiO 2 composite ceramic decreased, especially for samples sintered at 1000 °C, obvious decline in degradation efficiency was observed. The further investigation on photocatalytic degradation of methyl blue (MB) were carried out using ceramics sintered at 880 °C (TFC-880), which exhibited moderate physical and photocatalytical properties. The result showed that TFC-880 exhibited a high photodegradation capability for MB under either UV or visible light. Even in the third circle, it also showed a high degradation rate, meaning it has an extended application such as water treatment.
研究领域:
材料科学
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
CATALYSIS TODAY
·
2016
·
IF 4.312
Peng Sun,Ruiyang Xue,Wang Zhang,Imran Zada,Qinglei Liu,Jiajun Gu,Huilan Su,Zhijian Zhang,Jianzhong Zhang,Di Zhang
Herein TiO 2 coated on glass fiber cloth (TiO 2 /glass fiber cloth, TGFC) was synthesised by sol-gel method. We demonstrated the property about TGFC of photocatalytic decomposition of organic pollutants under ultraviolet-visible (UV–vis) light and sunlight. Glass fiber cloth (GFC) was chosen as the support of TiO 2 in order to improve the practical applications for water purification . TGFC-1–6 were characterized by ERSEM, XRD and XPS. Photocatalytic decomposition of crystal violet (CV) was carried out to investigate the photocatalytic activity of TGFC. The efficiency of TGFC-3 was the best. And its photocatalytic decomposition rate of the second to fifth cycle was higher than the first cycle. The photocatalytic decomposition rate of TGFC-3 was 85% under sunlight from 8:00–14:00. We could design and regulate the shape of TGFC and estimate the area, weight and thickness of TiO 2 , more easily than glass fibers. TGFC is suitable for photocatalytic decomposition of organic pollutants in the water, especially to be fixed in sewage treatment pool and reused.
研究领域:
环境科学
·
材料科学
✓ 已验证
产品关联
DOI
高影响因子
NEW JOURNAL OF CHEMISTRY
·
2018
·Vol. 42
·期 22
·18381-18387
·
IF 3.201
Hang Cheong Chan,Ting Chen,Lifang Xie,Yijin Shu,Qingsheng Gao
As promising catalyst supports, hydrogenated metal-oxides can afford engineered surface architectures and electronic configurations to promote catalytic turnover on loading metals. Herein, hydrogenated TiO2 (H-TiO2) fabricated via NaBH4 reduction is successfully introduced to boost the catalytic oxidation of formaldehyde (HCHO), which is one of the most common and harmful indoor volatile organic compounds. Distinct from the parent TiO2, H-TiO2 features enriched surface hydroxyls and enhanced metal–support interactions upon loading Ir, which are responsible for remarkable promotion in HCHO oxidation. In particular, the abundant hydroxyls on H-TiO2 promote the generation of HCOO−, which is believed to be the rate-determining step in HCHO oxidation. This discovery is anticipated to pave the way for exploring high-performance metal catalysts on oxide supports via surface and interfacial engineering.
研究领域:
材料科学
·
催化化学
✓ 已验证
产品关联
DOI
高影响因子
POLYMER COMPOSITES
·
2023
·Vol. 44
·期 11
·7499-7509
·
IF 5.2
Jian Li,Jing Sun,Lulu Ren,Ting Lei,Juan Li,Jinbo Jin,Shanshan Luo,Shuhao Qin,Chengtao Gao,Ting Lei
The non-solvent induced phase separation technology was introduced to formulate titanium dioxide (TiO 2 )-hydroxyapatite (HAP) composite modified polyvinylidene fluoride (PVDF) ultrafiltration (UF) membranes, and research was conducted to explore the effect on PVDF UF membrane performance exerted by different addition amounts (0–1.0 wt%) of TiO 2 -HAP composite. The results indicated that when 0.3% TiO 2 -HAP composite was added, the composite membranes had a through-channel structure, with a uniform pore structure on the surface, so that they possessed a certainly raised pure water flux. Specifically, in contrast to the pure PVDF membrane, 0.3%-TiO 2 -HAP@PVDF UF membrane exhibited an incremented pure water flux by 59.09%. Besides, TiO 2 -HAP@PVDF UF membranes had decreased rejection rate of bovine serum albumin (BSA) together with water contact angle to 58.62% and 70.17°, respectively, compared to the pure PVDF membrane (85.52% & 92.75°), showing good hydrophilicity. Several pure water flux tests on the composite UF membranes revealed that the flux tended to be stable after the 4th test. In summary, the addition of TiO 2 -HAP composite is capable of efficiently ameliorating PVDF base membranes from the aspects of microstructure, hydrophilicity, antifouling properties, as well as stability, allowing a good application prospect in actual water treatment. Highlights The HAP can solve the poor adsorption of TiO 2 . The TiO 2 can improves the interfacial adhesion between HAP and polymer. The TiO 2 -HAP composite with excellent stability, corrosion resistance and et al. The TiO 2 -HAP@PVDF UF membrane with anti-pollution performance and stability.
研究领域:
材料科学
·
环境工程
·
膜技术
✓ 已验证
产品关联
DOI
高影响因子
Catalysis Science & Technology
·
2023
·Vol. 13
·期 15
·4525-4533
·
IF 5
Qiuyu Zhang,Yajie Chen,Xinyan Yu,Yuejia Yin,Yaxin Ru,Guohui Tian
Fabricating photocatalysts with customizable structure and composition using different metal–organic framework (MOF) building blocks has intriguing implications in chemistry and material science, but it is challenging to do so. Here, a two-step synthetic strategy was designed to prepare MIL-125(Ti)@TiO2 hollow nanodiscs decorated with Co3S4 nanoparticles for CO2 photoreduction. The Co-based zeolite imidazolium ester backbone (ZIF-67) nanolayer was first loaded on the prepared MIL-125(Ti) nanodiscs to form core@shell MIL-125(Ti)@ZIF-67 nanodiscs. The following sulfidation process under solvothermal condition led to the production of MIL-125(Ti)@TiO2 hollow nanodiscs decorated with Co3S4 nanoparticles (MIL-125(Ti)@TiO2\Co3S4). This ternary hybrid catalyst with hollow nanodisc structure possessed a significantly enhanced charge separation efficiency and visible light absorption, along with offering a huge number of active sites. Considering the above advantages, the CO2 photoreduction activity of the optimized MIL-125(Ti)@TiO2\Co3S4 catalyst was significantly increased when compared to single-component catalysts (MIL-125(Ti), TiO2, and Co3S4) and binary hybrid catalysts (MIL-125(Ti)@TiO2 and TiO2\Co3S4) under simulated sunlight irradiation. CO is the main product with a productivity of 587.50 μmol g−1 h−1, which is almost seven times higher than that of pure MIL-125(Ti). The potential photocatalytic mechanism of the hybrid photocatalyst has also been demonstrated. This study presents a simple and effective technique for fabricating MOF-based hybrid catalysts for photocatalytic applications.
研究领域:
材料科学
·
化学
✓ 已验证
产品关联
DOI
高影响因子
Science of Advanced Materials
·
2022
·Vol. 14
·期 3
·576-580
·
IF 1.067
Tang Si-Lu,Liu Ya-Lin,Li Xu-Ming,Chen Qian-Wen,Chen Heng-Yu,Zhou Ji-Li,Chen Liang,Gu Zi-Yi,Shao Shi-Xing,Qiao Pei-Zhi,Shen Guo-Dong,Yang Bing-Chuan
The core–shell TiO2 nano-layer spheres were synthesized by hydrothermal method without surfactant, using tetraisopropyl titanate, diethylenetriamine and water as the capping agents. The structure of the products was characterized with X-ray diffraction (XRD), transmission
electron microscope (TEM) and scanning electron microscopy (SEM). The possible formation mechanism and electrocatalytic degradation characters of the products were also discussed.
研究领域:
材料科学
·
环境科学
✓ 已验证
DOI
高影响因子
INTERNATIONAL JOURNAL OF PHOTOENERGY
·
2014
·
IF 0
Sujing Yu,Juncheng Hu,Jinlin Li
Self assembly of TiO2/CdS mesoporous microspheres was synthesized via hydrothermal method. The samples were characterized by X-ray powder diffraction (XRD), ultraviolet-visible diffuse reflectance spectroscopy (DRS), transmission electron microscopy (TEM), energy-dispersive spectroscopy analysis (EDS), high-resolution transmission electron microscopy (HRTEM), Brunauer-Emmett-Teller (BET), X-ray photoelectron spectroscopy (XPS), and photoluminescence spectra (PL). The as-synthesized TiO2/CdS mesoporous microspheres showed superior photocatalytic activity for the degradation of RhB under either visible light or simulated sunlight irradiation; the 10 wt% TiO2/CdS sample showed the best performance. Moreover, this catalyst showed improved stability, and the activity did not decrease significantly after four recycles. The heterojunction between TiO2 and CdS may be favorable for the transport of photoinduced electrons from CdS to TiO2. In addition, the mesoporous structure could increase the utilization of light energy and facilitate the diffusion of reactants and products during the photocatalytic reaction.
研究领域:
材料科学
·
环境科学
✓ 已验证
DOI
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY
·
2017
·
IF 3.454
Atta Ullah,Hanxing Liu,Hua Hao,Javed Iqbal,Zhonghua Yao,Minghe Cao
(1- x )Mg 0.90 Ni 0.1 SiO 3 - x TiO 2 ( x = 0, 0.01, 0.03, 0.05) ceramics were successfully formed by the conventional solid-state methods and characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS), and their microstructure and microwave dielectric properties systematically investigated. It was observed that when TiO 2 content increased from 0 to 5 wt%, the Q u f o of the sample decreased from 118,702 GHz to 101,307 GHz and increases the τ f value from −10 ppm/°C to +3.14 ppm/°C accompanied by a notable lowering in the sintering temperature (125 °C). A good combination of microwave dielectric properties (ε r ∼ 8.29, Q u f o ∼ 101,307 GHz and τ f ∼ −2.98 ppm/°C) were achieved for Mg 0.90 Ni 0.1 SiO 3 containing 3 wt% of TiO 2 sintered at 1300 °C for 9 h which make this material of possible interest for millimeter wave applications.
研究领域:
材料科学
·
电子工程
✓ 已验证
DOI
高影响因子
JOURNAL OF PHOTOCHEMISTRY AND PHOTOBIOLOGY A-CHEMISTRY
·
2024
·
IF 4.1
Mingtao Wang,Shijie Wang,Zhenzi Li,Xuepeng Wang,Liping Guo,Haixia Liu,Lijun Liao,Wei Zhou
Photocatalysis is an alternative for antibiotics removal from wastewater for the sustainable development of human society. However, applying photocatalysts for antibiotics (e.g., tetracycline) degradation under practical conditions is highly restricted by the low reaction efficiency due to the prompt charge recombination. Constructing porous heterojunctions is an efficient way to regulate the electron transfer path and accelerate charge migration efficiency. Herein, TiO 2 /defective UiO-66 porous octahedral S-scheme heterojunctions are successfully fabricated through an in-situ growth strategy. The strong interaction and charge migration behavior between TiO 2 and defective UiO-66 have been studied using X-ray photoelectron spectroscopy and electron paramagnetic resonance measurements. The photocatalytic removal efficiency of tetracycline is notably improved by forming TiO 2 /defective UiO-66 porous heterojunctions. The promoted photocatalytic performance can be ascribed to the strong interaction between TiO 2 and defective UiO-66, and the accelerated charge separation and transfer efficiency due to the formation of S-scheme heterojunctions, thus generating abundant reactive oxygen species, including O 2 − and OH. The optimized 38-TiO 2 /UiO-66-300 can eliminate 97.9 % of tetracycline in 60 min with a reaction constant rate of 0.0425 min −1 , which is approximately 4 and 10 times that of pristine TiO 2 and UiO-66-300, respectively. This work provides an alternate strategy for preparing highly active heterojunction photocatalysts for environmental applications.
研究领域:
环境科学
·
材料科学
·
光催化技术
✓ 已验证
产品关联
DOI
高影响因子
PROGRESS IN ORGANIC COATINGS
·
2024
·
IF 6.5
Le Zhang,Rui Li,Hao Ding,Daimei Chen,Xuan Wang
Coatings with superamphiphobicity and photocatalytic degradation properties to achieve excellent self-cleaning performance have received extensive attention. Herein, TiO 2 -SiO 2 composite particles with micro-/nanoscale hierarchical structures were fabricated by hydrophobic agglomeration. The TiO 2 -SiO 2 was modified with 1H, 1H, 2H, 2H-perfluorodecyltriethoxysilane (PFDTS), and then it was sprayed onto the surfaces of substrates to obtain TiO 2 -SiO 2 /PFDTS coatings. The coating surface exhibited superamphiphobicity and low adhesion properties. The contact angles (CAs) of water, ethylene glycol, glycerol, and hexadecane on the coating surface were 163.5°, 154.6°, 157.3°, and 150.2°, respectively. The slide angles (SAs) of the above droplets on the coating surface were 0.4°, 2.7°, 1.6°, and 11.1°, respectively. In addition, 80.9 % methyl orange solution (10 ppm) was degraded by the TiO 2 -SiO 2 /PFDTS under UV irradiation in 60 min, demonstrating an excellent photocatalytic degradation performance. It also had good adaptability to different substrates, liquids with different properties, and outdoor environments. The results of a mechanistic study showed that SiO 2 and TiO 2 were connected by the carbon chains of modifiers. PFDTS and TiO 2 -SiO 2 might be combined by chemical bonds or surface carbon chains. The hierarchical structure of TiO 2 -SiO 2 and the low surface energy of PFDTS resulted in the superamphiphobic property of the TiO 2 -SiO 2 /PFDTS coating.
研究领域:
材料科学
·
环境科学
✓ 已验证
产品关联
DOI
高影响因子
Catalysts
·
2022
·Vol. 12
·期 3
·297
·
IF 4.501
Dingqing Yang,Jinyang Chen,Xiaomin Hong,Jingying Cui,Lingzhen Li
TiO2/hectorite composite photocatalysts with different molar ratios of lithium, magnesium, and silicon were synthesized by a one-pot hydrothermal method. The samples were characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), N2adsorption-desorption isotherms, and ultraviolet-visible diffuse reflectance spectra (UV-Vis DRS). When the molar ratio of lithium, magnesium, and silicon was 1.32:5.34:8 (TH-2), the composite showed the highest UV photocatalytic degradation of methylene blue (MB). The apparent rate constant of TH-2 was 0.04361 min−1, which was about 3.12 times that of EVONIK Degussa commercial TiO2of AEROXIDE P25. The improvement of photocatalytic efficiency of the composite was mainly due to its high specific surface area, light trapping ability, and effective separation of electrons (e−) and holes (h+). At the same time, the F element of hectorite is beneficial to the formation of Ti3+in TiO2, thus enhancing the photocatalytic activity. After five cycles, the removal rate of MB with TH-2 still reached 87.9%, indicating its excellent reusability.Keywords:photocatalysis;TiO2;hectorite;one-pot synthesis;degradation of organic dyes
研究领域:
材料科学
·
环境科学
✓ 已验证
DOI
高影响因子