JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2026
·
IF 9.6
Jian Cui,Qian Zheng,Yifeng Zeng,Yuchun Liu,Chunxia Wang,Xingdong Wang,Guoyong Huang
Hydrogen spillover provides a powerful route to overcome hydrogen binding ability and sluggish water dissociation kinetics in alkaline hydrogen evolution reaction (HER). Here, we present a catalyst with Pt nanoparticles supported on a nonmetallic support (C 3 N 4 ), which achieves efficient hydrogen evolution kinetics and exceptional stability through the hydrogen spillover effect. Density functional theory (DFT) calculations reveals that strong Pt N coordination induces interfacial electron transfer from Pt to C 3 N 4 , establishing a vertical interfacial electric field that drives hydrogen spillover. As a result, Pt/C 3 N 4 –500 delivers industrial-level current densities of 500 and 1000 mA cm −2 at ultralow overpotentials of 89.8 ± 1.5 and 137.7 ± 2.1 mV, respectively, in a three-electrode system. It also maintains stable operation at 500 mA cm −2 for 300 h with a minimal potential variation of just 42.2 mV. In situ electrochemical impedance spectroscopy, in situ Raman spectroscopy, and DFT calculations reveal that the C 3 N 4 support optimizes the kinetics of H 2 desorption (0.8 × 10 −4 s), induces a hydrogen spillover effect, and facilitates the transfer of H* intermediates to the C 3 N 4 (0.37 eV) surface for desorption via low Δ G H⁎ (−0.04 eV) at the interfacial Pt sites. Anion exchange membrane water electrolyzers (AEMWE) using Pt/C 3 N 4 –500 as the cathode requires only 1.73 ± 0.02 V to achieve a current density of 1 A cm −2 and operates stably for over 150 h at 1 A cm −2 .
✓ 已验证
产品关联
DOI
PubMed
高影响因子
MICROELECTRONICS RELIABILITY
·
2026
·
IF 2.5
Tao Yang,Guoyou Gan,Xianglei Yu,Hu Sun,Junpeng Li
This study investigates the electrical properties and stability of resistor pastes formulated from RuO 2 –CuO composites doped with La 2 O 3 . The pastes exhibit an approximately linear positive temperature coefficient (PTC) of resistance behavior, referred to as near-linear positive temperature coefficient of resistance (TCR) in this work, to emphasize the linearity of the resistance-temperature relationship, with optimal performance achieved at 1.2 wt% La 2 O 3 doping. Microstructural analyses indicate that La 2 O 3 promotes densification of the resistive layer, enhancing the stability of the conductive network. After 1000 h of storage at room temperature, the resistance change rate is approximately 0.5%. Under high-temperature conditions (150 °C for 240 h), the rate increases slightly to about 2%, demonstrating satisfactory preliminary stability.
✓ 已验证
产品关联
DOI
高影响因子
CARBOHYDRATE POLYMERS
·
2026
·
IF 13.2
Onome Ejeromedoghene,Moses Kumi,Huanhuan Wang,Samson Olusegun Afolabi,Ahmed Olalekan Omoniyi,Huaguang Wang,Jiangna Guo,Zexin Zhang
The limitations of conventional hydrogels have spurred a growing interest in enhancing polymeric compounds with inorganic nanoparticles to create hydrogel composites with multifunctional properties for various applications. This study reports a one-step chemical gelation system for fabricating hydrogel composites consisting of carboxymethyl cellulose, acrylamide, and gold nanoparticles. The hydrogel composites exhibited significant mechanical and adhesive strength attributed to the strong hydrogen-bonding interaction within the polymer network. Remarkably, the composites achieved a tensile strength of 22.8 MPa with a yield strain of 877.1%, a compressive strength of 346.8 MPa with a yield strain of 120%, and an adhesion strength of 246 kPa. The materials also demonstrated remarkable adhesion performance on different biological and inorganic substrates, maintaining higher adhesion stress across a range of displacements. Furthermore, the hydrogel composites exhibited superior bactericidal activity, achieving up to 98.2% efficacy against E. coli and 99.1% against S. aureus , while showing non-toxicity to mammalian cells. These findings highlight the practical potential of these hydrogel composites in applications such as wound healing and antibacterial bioadhesives.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2026
·
IF 12.5
Pingping Lu,Qiuyi Ji,Xiaoqian Ye,Guanshun Wang,Yangbo Cheng,Wendi Zhou,Zhe Xu,Gancheng Zuo,Xin Jin,Guoyang Zhang,Limin Zhang,Huan He
The practical application of perylene diimide (PDI) supramolecules is significantly hampered by their structural instability, which manifests as dissociation under alkaline conditions and deterioration during cyclic reactions. A thiourea-functionalized perylene diimide polymer with a reinforced π-conjugated framework (T-PDI) was synthesized for visible-light-driven (Vis) peroxymonosulfate (PMS) activation. The enhanced π-conjugation, synergizing with sulfur doping, endowed T-PDI with superior visible-light absorption and charge separation efficiency compared to urea-functionalized PDI (U-PDI). Experimental and theoretical analyses revealed that the robust π-conjugated network facilitated strong π-π stacking and directed spatial separation of electron-hole pairs, effectively suppressing recombination. Consequently, the T-PDI/PMS/Vis system achieved complete degradation of bisphenol A within 17.5 min ( k = 0.197 min −1 ), 1.5-times faster than the U-PDI/PMS/Vis system ( k = 0.134 min −1 ). The system also demonstrated excellent stability over multiple cycles, broad pH adaptability, and strong resistance to common water matrix interferents. This work highlights the critical role of π-conjugation engineering in developing high-performance, metal-free polymer photocatalysts for advanced oxidation processes.
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2026
·
IF 9.1
Zhihao Gao,Zhiyou Pu,Peiwen Yan,Xiaonan Fu,Siming Pang,Zhenyu Cui
To address the challenges of insufficient permeability and long-term operational stability for microfiltration (MF) membranes in biopharmaceutical sterilization applications, in this study, a preparation process based on the coupling of reverse thermally induced phase separation (RTIPS) and vapor-induced phase separation (VIPS) was developed to fabricate the polyethersulfone (PES) MF membranes with a funnel-like pore structure, high surface porosity, and narrow pore size distribution. The effects of the temperature of the casting solution, ambient humidity and the exposure time on the membrane structure and performance were systematically investigated. The results indicated that as the temperature of the casting solution increased, the thickness of the loose layer for the membrane gradually increased, accompanied by significant enhancements in pore size, porosity, and pure water permeability (PWP). The PWP increased from 6634.3 to 9032.7 L m −2 h −1 bar −1 . The increase in humidity significantly enhanced the mechanical properties of the membranes (from 4.2 MPa for M 58 – 35-4 to 5.5 MPa for M 58 – 80-4 ) and simultaneously improved the rejection rate of E. coli and the flux retention rate (maintaining 68% after 3 h of operation, significantly higher than the 36% of the M-RTIPS membrane). Combined with thermodynamic analysis and molecular dynamics (MD) simulations, the “wet inverse heat synergistic induction” phase separation mechanism was revealed from the perspectives of free volume fraction (FFV) and mean squared displacement (MSD). This study provides a new strategy for fabricating high-performance MF membranes and offers a theoretical basis for efficient sterilization in the biopharmaceutical field.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF POWER SOURCES
·
2026
·
IF 8.4
Xinyang Lu,Hezhan Yu,Yu Yang,Qing Xu,Kai Zhao,Jun Li,Min Chen
Proton-conducting solid oxide fuel cells (H-SOFCs) demonstrate substantial potential for intermediate-to-low temperature operation due to the lower migration activation energy of protons (H + ) compared to oxygen ions (O 2− ). To address the critical role of cathode materials in determining cell performance, this study employs an A-site silver (Ag) doping strategy in perovskite oxide. BaCo 0.4 Fe 0.4 Zr 0.1 Y 0.1 O 3-δ (BCFZY), Ba 0.95 Ag 0.05 Co 0.4 Fe 0.4 Zr 0.1 Y 0.1 O 3-δ (BACFZY) and Ba 0.9 Ag 0.1 Co 0.4 Fe 0.4 Zr 0.1 Y 0.1 O 3-δ (BACFZY-1) materials are all prepared using the sol-gel synthesis method. The investigation into the structure and element distribution of the synthesized materials reveals that BACFZY remains in a pure perovskite phase, with all elements evenly dispersed throughout. Ag-doped BACFZY surpasses BCFZY with greater electrical conductivity and thermal expansion compatibility. Moreover, the incorporation of Ag in BACFZY cathode facilitate the oxygen adsorption, leading to lower impedance and superior output performance with maximum peak power density of 1160 mW cm −2 at 650 °C. Meanwhile, The BACFZY cell maintained stable operation for 100 h. The aforementioned experimental findings indicate that the BACFZY material is a promising cathode for H-SOFC.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2026
·
IF 12.5
Xueyan Chen,Hua Deng,Min Chen,Xiaoxiao Qin,Ling Wang,Changbin Zhang
Supports play a pivotal role in noble metal-supported catalysts by regulating the dispersion, electronic structure, and interfacial interactions of active species, as well as influencing the adsorption and activation of reactants. Herein, we demonstrated that the coordination structure of oxide supports critically dictates the catalytic performance of Ag-based catalysts in formaldehyde (HCHO) oxidation. Although Ag/Al 2 O 3 and Ag/TiO 2 possessed comparable Ag particle sizes, oxidation states, and redox properties, their activities differed substantially: Ag/Al 2 O 3 achieved complete HCHO conversion at 80 °C, while Ag/TiO 2 required 170 °C under identical conditions. In situ DRIFTS results revealed that HCHO was transformed into formate intermediates on both supports, but Al 2 O 3 stabilized two distinct formate configurations, whereas TiO 2 favored a single adsorption mode. More importantly, formates on Ag/Al 2 O 3 decomposed at much lower temperatures than those on Ag/TiO 2 , suggesting enhanced intermediate reactivity. Density functional theory (DFT) calculations confirmed that the diverse coordination environments of surface Al atoms enable multiple formate adsorption modes with lower C H bond dissociation barriers compared to Ti sites. These results establish that the support coordination structure governs intermediate configurations and their transformation kinetics, offering mechanistic insights into the superior oxidation activity of Ag/Al 2 O 3 and providing guidance for the rational design of efficient Ag-based catalysts for HCHO purification.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF FOOD COMPOSITION AND ANALYSIS
·
2026
·
IF 5.3
WeiHang Yao,JunYi Ye,PingPing Shen,Richa Raj,BoYang Yu,Xiaorong He,Jian Zhang
This study aims to expand the application of handheld near-infrared spectroscopy combined with machine learning in quantitative analysis of Epimedium . After establishing and evaluating several promising models: Gradient Boosting Regression (GBR), Extra Trees (ET), Extreme Gradient Boosting (eXGB), Support Vector Regression (SVR), Random Forest (RF), Partial Least Squares Regression (PLSR), we selected PLSR and SVR for further optimization due to their excellent performance in terms of R 2 and RMSE. Employing the NIPPY library for data preprocessing and a genetic algorithm for feature selection, models for predicting the contents of four active components in Epimedium were successfully established. The GA-SVR hybrid model delivered the following predictive performance for the four target components: icariin (R 2 :0.9556, RMSE:0.0031, Avg. MAPE:2.07%), epimedin A (R 2 :.9586, RMSE:0.0004, Avg. MAPE:3.60%), epimedin B (R 2 :0.9432, RMSE:0.0003, Avg. MAPE:3.58%) and epimedin C (R 2 :0.9232, RMSE:0.0182, Avg. MAPE:2.33%). These findings establish a novel paradigm for high-throughput analysis and quality assessment of food and traditional Chinese medicine active ingredients.
✓ 已验证
产品关联
DOI
高影响因子
OPTICAL MATERIALS
·
2026
·
IF 4.3
Kashif Abbas,Peirui Ji,Muhammad Faizan Ameer,Shuming Yang
Graphene quantum dots (GQDs) exhibit pronounced quantum confinement and edge effects, resulting in tunable band gaps, high photostability, and chemical robustness, which make them promising candidates for optoelectronic applications. In this work, GQDs were probe sonicated using three organic solvents, N–methyl–2–pyrrolidone (NMP), dimethylformamide (DMF), and dichloromethane (DCM) to elucidate the role of solvent properties on exfoliation efficiency and resulting structure property relationships. Structural and morphological analysis revealed pronounced solvent–dependent differences. GQDs produced in NMP exhibited the smallest lateral dimensions (∼2–10 nm), narrow thickness distribution (∼1.6–6.1 nm), and improved structural ordering, as evidenced by a relatively sharp (002) diffraction feature and the lowest Raman I D /I G ratio (0.34), indicating reduced defect density. UV–visible absorption spectra showed a blue–shifted absorption edge for NMP–derived GQDs, while optical band gaps estimated from Tauc plots yielded values of 2.75 eV (NMP), 2.53 eV (DMF), and 2.35 eV (DCM). Consistently, photoluminescence measurements revealed the strongest and most blue–shifted emission for NMP–exfoliated GQDs, confirming enhanced quantum confinement and suppressed non–radiative recombination. These results demonstrate that solvent selection critically governs the structural and optical quality of GQDs, with NMP enabling the formation of highly uniform and optically superior GQDs suitable for scalable optoelectronic applications.
✓ 已验证
产品关联
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2026
·
IF 6
Yu Liu,Lin Yuan,Juntao Wang,Danchi Zhou,Nana Xu
Mullite nanofibers demonstrate significant potential for high-temperature insulation applications, yet their performance is often compromised by abnormal grain growth and mechanical property degradation at elevated temperatures. Herein, we propose a La-doping strategy to precisely control the microstructure of mullite fibers, enabling uniform and rapid densification sintering at reduced temperatures while enhancing thermal stability. Experimental results reveal that La-doped mullite fiber membranes exhibit remarkable improvements in high-temperature mechanical properties, with a 10% increase in tensile strength and a 75% improvement in tensile strain at 1300 °C. Furthermore, the doped membranes demonstrate superior thermal insulation performance, with thermal conductivities of 0.045 W m −1 K −1 (room temperature) and 0.149 W m −1 K −1 (1000 °C), respectively. This innovative La-doped approach endows mullite nanofibers with exceptional thermal stability and insulation capabilities, positioning them as promising candidates for advanced thermal protection systems in aerospace applications and high-temperature insulation in metallurgical kilns.
✓ 已验证
产品关联
DOI
高影响因子
SENSORS AND ACTUATORS B-CHEMICAL
·
2026
·
IF 8.3
Yaping Tian,Ran Xu,Luqing Chen,Yuanyuan Liu,Xinming Nie,Xinyu Liu,Shoufeng Tang,Lulu Qu
Nitrogen oxides from construction machinery exhaust pose a significant threat to the environment and human health. Therefore, effective capture and highly selective detection of NO 2 is of utmost importance. Surface-enhanced Raman scattering (SERS) is a spectroscopic technique that provides molecular fingerprint information and enables qualitative and quantitative analysis of molecules at extremely low concentrations. However, the application of SERS for gas molecules with small scattering cross sections, such as NO 2 , is still in its infancy. Based on this, a sensing device for capturing and selectively detecting NO 2 from construction machinery exhaust was developed. The device consists of a gas collection module and a Raman signal amplification module containing a 4, 4’-diaminodiphenyl disulfide (APDS) probe-modified flexible Au@PDMS chip. The Au@PDMS chip amplifies the Raman signals of molecules, while the APDS selectively and rapidly captures NO 2 . The proximal electron-rich nitrogen atom and the ortho-electron-poor aromatic hydrogen atom of the APDS probe form a stable six-membered ring complex with the N atom of NO 2 , and hydrogen bonding interactions occur between the H atom in APDS and the O atom in NO 2 . This ring complexation allows the Au@PDMS chip to capture NO 2 quickly and effectively, resulting in changes in SERS signals and facilitating quantitative analysis of NO 2 . Combined with the gas detection device, the chip can identify NO 2 within 5 min with a detection limit of 3.5 ppm. This sensor device has high selectivity for NO 2 detection in real exhaust gases and has great potential for practical detection of construction machinery exhaust gases.
✓ 已验证
产品关联
DOI
高影响因子
INTERNATIONAL JOURNAL OF HYDROGEN ENERGY
·
2026
·
IF 9.2
Bin Hou,Wenyuan Chen,Shufeng Yang,Shengyang Zheng,Zhiqiang Xie,Gaoqiang Yang
Reaction mechanism, like the reaction site distribution on the catalyst layer, is crucial for PEM water electrolyzer development. Here, we analyze how input voltage affects the reaction site distribution using a visible coplanar electrode proton exchange membrane water electrolyzer (PEMWE). It is discovered that the reaction site distribution is in a limited range at the responding input voltage and there is a positive correlation due to the non-uniform potential distribution. Based on these findings, we define the concept of “voltage threshold” and further optimize a previous numerical model of the catalyst layer by introducing the reaction onset voltage. The strong agreement between experimental and simulation data resulting from the developed model demonstrates its feasibility. These results provide a novel perspective, method, and numerical model for a more comprehensive and realistic assessment of the reaction site distribution inside the electrolyzer.
✓ 已验证
产品关联
DOI
高影响因子