CHEMISTRY OF MATERIALS
·
2026
·
IF 7.1
Juan Wen,Fang Wang,Jingyuan Li,Yujie Wen,Xiaoli Xia,Zhonghan Feng,Zhengting Zhang,Xiaokang Ke,Wei Li,Sheng Tang,Luming Peng
Regulating the local coordination environment of active sites is an effective strategy to enhance the intrinsic activity of layered double hydroxides (LDHs) for the oxygen evolution reaction (OER). Here we report a controlled postsynthesis Fe incorporation approach that uses NiAl-LDH as a structurally robust host to construct NiAl(a)-Fe(e)-LDH with distorted local Fe coordination environments through alkali treatment and ultrasonic assistance. The resulting catalyst exhibits superior OER performance compared to counterparts with similar Fe content, highlighting the critical role of Fe coordination. Solid-state NMR and X-ray absorption fine structure reveal that ultrasonic-assisted Fe incorporation induces Fe–O lattice distortion and modifies the local electronic states of Fe. Density functional theory calculations show that these distorted environments upshift the d-band center and lower the *OOH formation energy barrier, thereby accelerating OER kinetics. This work establishes a direct correlation between local Fe coordination, electronic structure, and catalytic activity and provides a general strategy for active-site engineering in LDH-based OER electrocatalysts.
✓ 已验证
产品关联
DOI
高影响因子
ACS Applied Electronic Materials
·
2026
·
IF 4.7
Sinan Lin,Yuanqi Wang,Hangyao Wu,Xin Gao,Chenyi Li,Yang Liu
All-organic dielectric polymers are promising high-temperature capacitive materials to enable energy storage applications in hybrid vehicles, deep oil, and gas extraction. However, semiconductor fillers with both a wide bandgap Eg and a high electron affinity Ea remain rarely reported. Here, we identify tetrabromo-1,4-benzoquinone (TBQ) as an alternative quinone-based small-molecule semiconductor, which exhibits a concurrently large Eg of 3.24 eV and Ea of 4.16 eV. We use TBQ to tune dielectric energy storage of benchmark polyetherimide (PEI). We find that the optimal TBQ doping level of 1.00 wt % yields the optimized dielectric energy storage properties. At 150 °C and 650 MV·m−1, the discharge energy density of PEI/TBQ reaches 6.6 J·cm−3 with a charge−discharge efficiency above 90%, which is superior to that of pristine PEI. These findings are expected to promote the development of all-organic dielectric polymers for high-temperature capacitive energy storage applications.
✓ 已验证
DOI
高影响因子
ACS Applied Nano Materials
·
2026
·
IF 5.8
Xinqian Xie,Haiyan Li,Xiang Hong,Songwang Yang
The integration of low-temperature, solution-processed inorganic electron transport layers (ETLs) into inverted flexible perovskite solar cells (f-PSCs) remains a critical challenge due to the polar solvent-induced damage of the underlying perovskite film. Conventional SnO2 nanocrystal ink based on polar solvents inevitably causes irreversible damage to the perovskite layer in inverted PSCs. Herein, we propose a nonpolar ink based on oleate modified SnO2 nanocrystals. Exchanging the hydrophilic surface groups with long-chain oleate ligands allows the SnO2 nanocrystals to be stably dispersed in a nonpolar solvent of n-hexane. This avoids polar solvent-induced damage to the perovskite film and enables the deposition of a dense, pinhole-free SnO2 film directly onto the perovskite layer. The oleate ligands ensure solvent orthogonality, and their long alkyl chains enable more complete displacement of surface hydroxyls and more thorough passivation of surface defects than short-chain ligands through interchain van der Waals interactions. Consequently, the resulting inverted f-PSCs exhibit suppressed nonradiative recombination and improved carrier extraction. This yields a record efficiency of 22.19%, the highest value reported to date for inverted f-PSCs using solution-processed SnO2 nanocrystal ETLs. Furthermore, the dense film morphology combined with the hydrophobic alkyl chains significantly enhances the environmental and mechanical stability of the inverted f-PSCs. This study demonstrates that ligand engineering of nanocrystals enables the solution-processed fabrication of inorganic ETLs with nonpolar solvents without compromising interfacial optoelectronic quality, offering a viable route toward all-solution-processed inverted f-PSCs.
✓ 已验证
DOI
高影响因子
JOURNAL OF AGRICULTURAL AND FOOD CHEMISTRY
·
2026
·
IF 6.7
Tingxiang Yang,Anyu Liu,Yangyang Mou,Maerziya Azhatijiang,Xinnan Luo,Tingyu Ye,Zhen Wang,Dong Hao Wang
Seafood provides important nutrients to our diets, particularly omega-3 polyunsaturated fatty acids (PUFAs). Compared with other common seafood, sea snails represent an underutilized resource that may be exploited to help meet global PUFA demands. However, sea snails exhibit complex fatty acid (FA) profiles, making an accurate and detailed characterization a considerable analytical challenge. By employing an advanced mass spectrometry (MS) technique, i.e., covalent adduct chemical ionization (CACI), we characterized the FA profiles of five commonly consumed sea snail species. A straightforward method was established to distinguish monounsaturated fatty acid methyl esters (FAMEs) from isobaric dimethyl acetals (DMA), verifiable by retention-time models. FAME double-bond positional isomers were further identified by CACI-MS/MS diagnostic ions. Sea snails are abundant in plasmalogens at 82–333 mg/100 g food and long-chain omega-3 PUFA up to 174 mg/100 g food. Therefore, sea snails, particularly saltwater varieties, show promise as mainstream seafood because of their high nutritional values.
✓ 已验证
DOI
PubMed
高影响因子
ACS Applied Polymer Materials
·
2026
·
IF 5.2
Yunjian Wu,Xuefeng Ye,Chengjie Li,Chao Gao,Qiulin Chen,Haoqin Chen,Chen Peng,Shuangshuang Tian,Xiaoxing Zhang
Traditional epoxy insulation materials are prone to irreparable damage during long-term operation, severely limiting the reliability and lifespan of electrical equipment. Their difficult degradability and recyclability pose significant environmental pressures. This study proposes a strategy based on a “rigid–flexible integrated” molecular design. By introducing hindered urea bonds and imine bonds, we successfully construct a dual-dynamic covalent bond epoxy resin network (HXVY-EP) with adjustable proportions, which not only addresses the self-repair and degradation issues of traditional epoxy resins but also compensates for the defect of network imbalance caused by dynamic bonds. Precise control of material properties can be achieved by adjusting the proportion of dynamic bonds. For example, H20V20-EP exhibits excellent thermodynamic performance with tensile strength up to 95.2 MPa and the initial decomposition temperature above 250 °C. H25V25-EP shows a power frequency dielectric loss as low as 0.00599 and breakdown strength up to 40.36 kV/mm, which can be used in the area of high-end electrical equipment with low loss and high voltage resistance. Importantly, the material can achieve self-repair of mechanical damage within 10 min at 110 °C. Moreover, the material can be efficiently degraded at room temperature using various solvents, providing a feasible, environmentally friendly recycling pathway for epoxy. This work has achieved the coordinated optimization of the dynamicity, stability, and functionality of epoxy resin, and has broad application prospects in the fields of power equipment, aerospace, and sustainable electronic packaging.
✓ 已验证
DOI
高影响因子
ACS Sustainable Chemistry & Engineering
·
2026
·
IF 7.6
Pengxiang Zhang,Yumeng Wu,Shuling Liu,Xiaofeng Zhang,Xianji Guo,Xianli Wu,Yanyan Liu,Baojun Li
Rational design of heteronuclear dual‑atom catalysts with strong electronic coupling and spatial complementarity for highly selective 4e– oxygen reduction reaction (ORR) remains a significant challenge in electrocatalysis. Herein, a catalyst, Fe–Bi diatomic structures anchored in a cellulose-derived activated carbon matrix (FeBiDA@CC), was obtained for ORR, in which the Fe and Bi atoms exerted a synergistic effect through strong electronic coupling. Bi modulates Fe's spin and electronic structure, while Fe promotes Bi electron polarization and activation of outer shell electrons. The Fe–Bi spatial distance in the dual metal sites geometrically matches O2 bond length, optimizing modes of adsorption and activation to facilitate the preferred 4e– ORR pathway and improve catalytic stability. FeBiDA@CC exhibits a half-wave potential of 0.93 V, an electron transfer number of 3.92–4.00, and a current loss of only 7.2% after 100 h for ORR. Liquid and flexible zinc-air batteries based on FeBiDA@CC as a cathode catalyst demonstrate outstanding peak power densities of 200.5 and 96.6 mW cm–2, respectively, alongside excellent long-term cycling stabilities of 10,800 and 438 cycles, respectively. This work offers a novel perspective for electronic structural regulation and design of p-block element-based catalysts, opening new possibilities for the design of catalysts in the energy storage field.
✓ 已验证
DOI
高影响因子
LANGMUIR
·
2026
·
IF 4.4
Yong Zhang,Debin Tong,Qiao Li,Jie Qi,Yang Wu,Yajun Ma,Hongsheng Lu
To address the limitation of a single stimulus source in traditional switching emulsion drag reducers, increasing the variety of responsive groups to emulsifiers is one of the effective measures to broaden the release window of switchable emulsions and enhance the dissolution efficiency of the drag reducer. By leveraging the strong designability and interfacial stability of nanoparticles, multiresponsive switchable emulsion drag reducers were constructed, which effectively simplify the complexity of controlling the release of drag reducers. Herein, based on the concept that the pH sensitivity of the imine bond and the complexation of N with lone electron pairs to metal ions, we have developed a novel strategy for the synthesis of pH-responsive metal–organic frameworks (MOFs) with high stability and recyclability. A nanoparticle (SiO2–NH2@DF-DAP) with pH- and salt responsiveness was constructed to stabilize the switching Pickering emulsion drag reducer. The response behavior of switching Pickering emulsions was confirmed by the conductivity and fluorescence methods. The most stable Pickering emulsion optimized by centrifugation was used as a template for the preparation of a switching Pickering emulsion drag reducer. The switching Pickering emulsion drag reducer exhibited remarkable storage stability even after 45 days because the nanoparticles could stably adsorb on the oil–water interface to form an interfacial film with a rigid multilayer structure. Importantly, the switching Pickering emulsion drag reducer was completely released in only 20 s under the dual response of pH (4) and salt (the concentration of MgCl2 was 70 mM). Besides, the drag reduction rate of the switching Pickering emulsion drag reducer was 65% at a concentration of 0.05 wt %. The successful construction of a switching Pickering emulsion drag reducer provides new strategies and insights for the efficient and rapid release of drag reducers.
✓ 已验证
DOI
PubMed
高影响因子
ACS Applied Materials & Interfaces
·
2026
·
IF 7.8
Pengze Xun,Yang Zou,Yonggang Lv
Flexible fiber capacitive tactile sensors hold promise for wearable human–machine interaction, yet balancing sensitivity with robustness while preserving textile softness remains challenging. To mitigate this trade-off, a capacitive tactile fiber based on the dual-mechanism enhancement of gradient-porous compression and Maxwell–Wagner interfacial polarization was developed. A fiber with a radial gradient-porous architecture, comprising a liquid metal (LM)/thermoplastic polyurethane (TPU) conductive core and a titanium dioxide (TiO2)/TPU dielectric sheath, was fabricated via coaxial wet spinning through non-solvent induced phase separation. A sub-percolating carbon nanotube/graphene oxide (CNT/GO) network was subsequently introduced onto the fiber surface to amplify the effective permittivity via interfacial charge accumulation. A sensitivity of 18.32 kPa–1, a response time of 170 ms, a hysteresis error of 4.47%, and stable signal retention over 1000 cycles were achieved. An all-textile wireless tactile platform was constructed and progressively validated from transient mouse clicking to quasi-static sitting posture monitoring (99.6% recognition accuracy) and further to a 64-key textile keyboard, where signal crosstalk was effectively decoupled through a fabric topology design and a one-dimensional convolutional neural network algorithm, yielding a character recognition accuracy of 96.36% and enabling context-aware generative artificial intelligence communication via integration with a large language model. This work demonstrates the significant potential of fiber-based tactile sensors for complex, multi-scenario human–machine interactions and provides new insights into the development of next-generation intelligent textile interaction platforms.
✓ 已验证
DOI
PubMed
高影响因子
JOURNAL OF THE AMERICAN SOCIETY FOR MASS SPECTROMETRY
·
2026
·
IF 2.9
Jun Huang,Zhiwei Wen,Tianci Xiao,Shijun Gao,Guangqi Wang,Yihan Tang,Minggao Xu,Chengyuan Liu,Yang Pan
In situ synchrotron radiation photoionization mass spectrometry (SR-PIMS) is a powerful tool for detecting gas-phase species including intermediates and products in gas–solid catalytic reactions. However, achieving sensitive and more comprehensive monitoring of gas-phase compounds with different ionization energies in a single measurement remains a significant challenge. In this work, a multiphysics ion trajectory simulation integrating a coupled computational fluid dynamics-direct simulation Monte Carlo (CFD-DSMC) method for continuum-rarefied flow was carried out for tracing the ion motion within the ionization region. The simulation results were applied to the design of the cage lens assembly of a modified SR-PIMS, and a limit of detection (LOD) of 0.67 ppbv (S/N ≥ 3) was achieved under Kr-lamp calibration conditions for toluene. Furthermore, a residual gas analyzer (RGA) was coupled to the SR-PIMS for the complementary detection of organic products with low ionization energies (IEs, generally lower than 11 eV) and H2, CO, CO2 etc. with higher IEs, thereby reducing the need for separate measurements at multiple photon energies. The optimized SR-PIMS setup combined with RGA was successfully applied to probe the intermediates and products generated during the methanol-to-hydrocarbons (MTH) reaction over ZnO/HZSM-5 catalysts, and the time-evolved profiles for major species under different ZnO loadings were obtained and analyzed.
✓ 已验证
DOI
PubMed
高影响因子
ACS Applied Nano Materials
·
2026
·
IF 5.8
Zeping Tan,Fei Wang,Wenhao Yi,Fuquan Xiong
Oil spills, sewage discharge, and organic solvent leakage pose serious threats to ecosystems and resource sustainability. However, most oil-absorbing sponges rely on costly modifications or nonrenewable petroleum-based raw materials. Here, we develop an all-lignocellulosic superhydrophobic wood sponge by integrating lignin nanospheres into a wood scaffold via liquid-phase deposition and stabilizing them with poly(dimethylsiloxane), achieving a low-cost and sustainable platform for oil–water separation. The obtained wood sponge combines superhydrophobicity, and high porosity, featuring a high water contact angle of 153.28° and exceptional coating robustness against extreme pH (2–12), wide temperature ranges (20–170 °C), and prolonged fluid impact (18 h), showing near-complete stress recovery at 30–50% strain and maintaining structural integrity over 150 compression cycles at 40% strain without plastic deformation. When the wood sponge was used for oil–water separation, it exhibited efficient oil adsorption above and below water with a high capacity of 6534.24 mg g–1 and sustained separation efficiencies of ∼89% (submerged) and ∼95% (exposed) over 10 cycles, alongside stable adsorption over 20 cycles. Simultaneously, the incorporation of lignin nanospheres imparts excellent photothermal performance to the superhydrophobic sponge, rapidly reaching 70.8 °C within 5 min under 1.5 kW m–2 irradiation and maintaining stable efficiency over 10 cycles, thereby boosting the adsorption rate of viscous reagents by about 4.0 times under illumination. The superhydrophobic wood sponge provides a promising and practical candidate for offshore crude oil spill remediation.
✓ 已验证
DOI
高影响因子
CHEMISTRY OF MATERIALS
·
2026
·
IF 7.1
Hao Zhang,Rui Wang,Can Tang,Chengkai Xu,Shuting Zhai,Weijun Zhao,Yongzhen Wu
Organic single-luminophore systems featuring regulated monomer–excimer emission constitute an attractive framework for adaptive photonic materials. Here, we report two thiophene-decorated fluorene derivatives, TDDF and MTDDF, designed to modulate molecular packing and excimer formation through heteroarene-involved interactions. Compared with the nonthiophene analogue DDF, thiophene incorporation decreases optical bandgaps, enhances thermal robustness, and promotes close intermolecular association, leading to pronounced excimer emission in aggregated states. Single-crystal analyses reveal that methyl substitution in MTDDF increases intermolecular spacing, enabling a finely tunable balance between monomeric and excimeric states. When dispersed in a fatty-acid phase-change matrix, MTDDF exhibits a distinct, reversible thermally modulated luminescence transition across the physiological temperature range, producing a continuous color shift from yellow-green to blue. This thermally driven packing reorganization enables highly sensitive ratiometric temperature readout, delivering a maximum sensitivity of 44% °C–1 near 37 °C, among the highest reported for organic luminescent thermometers. This work demonstrates thiophene decoration as an effective approach for stabilizing excimer states and provide a versatile design strategy for advanced thermoresponsive luminophores and stimuli-adaptive photonic materials.
✓ 已验证
产品关联
DOI
高影响因子
ACS Applied Polymer Materials
·
2026
·
IF 5.2
Shijie Zeng,Xin Wang,Xu Xiang
Hydrogel materials show significant promise for wearable devices and environmental sensing applications, yet conventional hydrogels suffer from poor mechanical durability and sluggish responsiveness to stimuli. To overcome these limitations, we developed a dual-network hydrogel (PAMSa) by integrating polyacrylamide (PAM) and sodium alginate (SA) networks with Cu2+ ions as dynamic cross-linking agents, successfully achieving simultaneous temperature sensitivity, self-powering capability, and robust mechanical performance in the PAMSaC-2 formulation. Characterization revealed that the hydrogel exhibits mechanical properties (650% strain, 247 kPa stress) alongside competitive electrical conductivity (0.264 S/m at 20 °C), with elevated temperatures inducing a phase transition of bound Cu2+ ions to mobile states that slightly reduces mechanical strength but significantly enhances conductivity (0.361 S/m at 70 °C) and improves energy supply efficiency in self-powered systems. A stacked series configuration of PAMSaC-2 synchronously amplifies voltage and current to directly power miniature devices like fans and oximeters, while its resistance changes enable real-time human joint motion monitoring with high sensitivity. Notably, a PAMSaC-2-based fire-warning system maintains reliable detection accuracy even after prolonged storage. This study establishes a paradigm for multifunctional integration in smart hydrogels, bridging mechanical resilience, adaptive functionality, and energy autonomy for next-generation wearable electronics and environmentally responsive sensors.
✓ 已验证
DOI
高影响因子