CHEMICAL ENGINEERING JOURNAL
·
2026
·
IF 13.2
Jing Duan,Yuyi Zhang,Shixiang Zhao,Yuri V. Petrov,Vladimir E. Baulin,Aslan Yu Tsivadze,Dechang Jia,Yu Zhou,Baoqiang Li
Biphasic hydrogels hold significant potential in fabricating isotropically tough materials through structural synergy, yet their strength remains constrained by interfacial modulus mismatch. Herein, a modulus-matched rubbery and entangled phases synergistic enhancement strategy is proposed to construct biphasic hydrogels by continuous phase separation. The molecular chain aggregates of the rubbery and entangled phases with nano crystalline domains are induced by continuous phase separation via reducing solvent polarity and breaking polymer-solvent hydrogen bonds, respectively. The key to achieving synergistic enhancement lies in modulus matching between the rubbery and entangled phases. Biphasic synergistic enhancement hydrogels exhibit excellent mechanical properties including a tensile strength of 38.76 MPa, a toughness of 137.03 MJ m −3 , a modulus of 58.36 MPa, and a fracture energy of 130.21 kJ m −2 . Biphasic hydrogels exhibit a low strength decay of 2.73% during ten cycles of testing at a strain of 3. Crucially, the modulus-matched biphasic system with crystalline domains transcends the stiffness-fracture energy trade-off boundary. The biphasic hydrogels exhibit heat resistance and stable electrical conductivity, making it suitable for flexible wearable electronics. It can function as a high-performance epidermal bioelectrode for monitoring human electromyography signals, demonstrating the integrated advantages of its strength, flexibility, reversible deformability, heat resistance, and stable ionic conductivity. Biphasic synergistic enhancement strategy paves the way for development of ultrastrong biphasic hydrogels via modulus matching.
✓ 已验证
产品关联
DOI
高影响因子
DALTON TRANSACTIONS
·
2026
·
IF 3.3
Lin Zhang,Qilong Tang,Zhipeng Wang,Chao Xu
The separation and recovery of neptunium (Np) represents a critical challenge in nuclear waste reprocessing. To address the difficulty of effectively capturing Np(V) in conventional extraction systems, this study designed and constructed three hydrophobic deep eutectic solvents (DESs) using tri-n-octylphosphine oxide (TOPO) as the hydrogen bond acceptor (HBA) and dihydroxybenzene isomers (catechol, CC; resorcinol, RC; hydroquinone, HQ) as hydrogen bond donors (HBD). These DESs enabled the in situ reduction at the liquid–liquid interface and highly efficient extraction of Np(V). Among them, the TOPO-CC DES system exhibited outstanding extraction performance for Np(V) over a broad acidity range of 10−3 to 2.0 M HNO3, achieving a single-stage distribution ratio (DNp) up to 85 and an in situ reduction conversion ratio from Np(V) to Np(IV) exceeding 98% within 5 minutes. Mechanistic investigations revealed that the extraction process follows a “coordination-driven reduction” mechanism. TOPO initially forms a weak coordination intermediate with Np(V) at the interface, thereby lowering its reduction potential. Subsequently, the dihydroxybenzene component facilitates efficient electron transfer within the organic phase, reducing Np(V) to Np(IV), which is strongly complexed and extracted by TOPO, completing an integrated “coordination–reduction–extraction” process. Furthermore, this system maintained stable extraction performance under challenging conditions, including high salinity (1–5 M NaNO3), a wide temperature range (293–313 K), and significant cumulative γ irradiation doses (up to 60 kGy). This study provides a novel integrated DES strategy for the efficient and green recovery of Np(V) and lays a scientific foundation for the application of functionalized deep eutectic solvents in advanced nuclear fuel cycles.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Journal of Environmental Chemical Engineering
·
2026
·Vol. 14
·期 2
·121460
·
IF 7.2
Xin Wang,Rui Fang,Ruyi Meng,Ruiding Fei,Zhiping Yan
Photocatalytic hydrogen evolution reaction (HER) represents one of the key technologies for realizing renewable energy conversion and storage. However, the precise development of efficient HER photocatalysts remains a critical challenge due to rapid charge recombination. In this study, the NiS/Zn 0.5 Cd 0.5 S (NZCS-X) Schottky junctions were successfully synthesized by hydrothermal deposition of NiS nanoparticles on coral-like Zn 0.5 Cd 0.5 S nanoclusters. Under visible light irradiation, the optimal composite material achieves a hydrogen evolution rate of 104.48 mmol h −1 g −1 —over 41 and 2 times higher than that of pristine CdS (2.52 mmol h −1 g −1 ) and Zn 0.5 Cd 0.5 S (47.92 mmol h −1 g −1 ). Mechanistically, X-ray photoelectron spectroscopy (XPS) confirms the electron transfer from Zn 0.5 Cd 0.5 S to NiS. Femtosecond transient absorption (fs-TA) spectroscopy reveals that the average carrier lifetime decreases to 4.83 ps in the composite, providing direct evidence of ultrafast interfacial electron extraction. Density functional theory (DFT) calculations further demonstrate that metallic NiS acts as an electron sink to optimize the Gibbs free energy (ΔG H∗ ). This work concludes that the synergistic engineering of morphology and Schottky interfaces is a decisive strategy for designing high-performance sulfide photocatalysts.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2026
·
IF 13.2
Yuanlong Xiang,Longlong Li,Yueyue Xiao,Zhongxin Zhang,Hui Yang,Hao Wu,Heping Zhang,Xudong Cheng,Yuelei Pan
Building fire accidents pose severe threats to human safety and infrastructure, highlighting the urgent need for advanced protective strategies for construction materials. Although numerous fireproof coatings have been developed, most suffer from limited durability, poor thermal insulation, or the requirement of thick multilayer structures to achieve satisfactory performance. Herein, we propose a multiscale composite coating strategy that combines silica aerogel with ceramic-forming fillers to enhance thermal insulation and fire resistance simultaneously. The introduction of silica aerogel endows the coating with an ultralow thermal conductivity, which remains as low as 0.04 W/(m·K) even after flame ablation, effectively blocking heat transfer. Meanwhile, the synergistic ceramization reaction between zinc borate and silica at elevated temperatures generates a compact ceramic layer with an internal porous structure, acting as an efficient thermal–fire barrier. Benefiting from this synergy, the optimized SSC@HI@CF coating achieves a limiting oxygen index (LOI) of 42.9%, while reducing peak heat release rate (PHRR) by 62% and smoke production rate (SPR) by 90.5% compared to the reference sample. This dual improvement in insulation and fire resistance demonstrates a feasible pathway for designing high-performance protective coatings, offering practical potential for safeguarding critical construction materials such as steel and wood against fire hazards.
✓ 已验证
DOI
高影响因子
ENVIRONMENTAL RESEARCH
·
2026
·
IF 7.7
Bo Tian,Jianwei Zhang,Wenze Li,Jinfeng Li,Na Zhou,Zhigang Li,Wa Gao,Nan Zhang,Hongtao Zhao
In this study, an innovative synergistic strategy combining radiation-induced graft polymerization and the cyanohydroxylamine method was employed to successfully construct a polyacrylamide/polybutadiene/polyacrylonitrile-amidoxime (PAM/PB/PAO) double-network (DN) hydrogel toughened by nano-polybutadiene rubber. Leveraging the DN topological design and rubber nano-phase reinforcement, this material exhibits exceptional fatigue performance (with a compressive stress retention rate of >90 % after 30 cycles of 80 % strain) and a high uranium adsorption capacity of 763.40 mg g −1 . In solutions containing seven competing ions, its distribution coefficient reaches 13,750.90 mL g −1 , and the adsorption efficiency remains above 91.10 % after 4 adsorption cycles. Density Functional Theory (DFT) calculations reveal that the amidoxime group serves as the primary adsorption site, which can form a multi-dentate chelating structure with the amide group. Additionally, the Intrinsic Bond Strength Index-Molecular Hamiltonian (IGMH) and Electron Density Analysis-Natural Orbital for Chemical Valence (EDA-NOCV) analyses further confirm the electrostatically dominated interaction mechanism. This research provides a novel insight into the design of high-strength and tough adsorbent materials, demonstrating promising application prospects in the field of uranium recovery from nuclear wastewater.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
CONSTRUCTION AND BUILDING MATERIALS
·
2026
·
IF 8
Heng Wang,Xiaoxing Liu,Xuemao Guan,João Castro-Gomes,Songhui Liu,Genshen Li
Magnesium slag (MS) carbonation offers significant potential for CO 2 sequestration and sustainable cement production, yet conventional wet carbonation suffers from limited efficiency due to surface passivation. This study investigates the synergistic effects of wet grinding carbonation coupled with sodium citrate (SC) addition on MS carbonation performance. Various conditions were evaluated, including magnetic stirring (M-0), colloid mill grinding (C-0), and grinding with SC dosages (C-0.4, C-1, C-3). The optimal condition (C-0.4) achieved CO 2 uptake of 40.29 % and carbonation degree of 79.21 %. Compared with traditional wet carbonation, the carbonation degree is increased by 89.14 %. Wet grinding effectively removes surface carbonate layers while optimal SC dosage (0.4 wt%) promotes calcium carbonate formation. The microstructural analysis demonstrated particle size reduction (D 50 from 19.60 to 4.68 μm) and increased specific surface area (6.92 × 10 −2 to 25.48 m 2 /g). When applied as cement replacement, carbonated MS (C-0.4) exhibited superior performance. With 10 % replacement, the 28-day compressive strength exceeded that of ordinary Portland cement by 6.91 MPa. The enhanced performance is attributed to pore filling and additional C-S-H gel formation. This work provides insights into coupling mechanisms of mechanical activation and chemical enhancement for efficient mineral carbonation, offering a promising pathway for industrial waste valorization.
✓ 已验证
产品关联
DOI
高影响因子
MICROCHEMICAL JOURNAL
·
2026
·
IF 5.1
Yang Liu,Weitao Li,Zhongyan Lu,Haoyang Cai,Ruiling Yuan,Yongqi Yang,Xuezhi Qiao
Monitoring biomarkers in interstitial fluid (ISF) offers a compelling alternative to blood analysis for managing chronic metabolic diseases, owing to the high correlation between ISF and blood analyte concentrations. Herein, we reported a biomimetic microneedle (MN) sensor based on Surface-Enhanced Raman Scattering (SERS) for the minimally invasive, simultaneous detection of pH and uric acid (UA). The sensoring platform functionalized with a plasmonic active interface, constructed via the in situ self-assembly of gold nanoparticles (AuNPs). Crucially, this dense AuNP layer serves a dual function: it creates high-density SERS “hot spots” for signal amplification and significantly improves surface hydrophilicity, thereby facilitating the efficient extraction and enrichment of analytes from the ISF matrix. The sensor displayed superior analytical performance for dual UA and pH detection, offering broad linear dynamic ranges and suitable monitoring intervals relevant to physiological conditions. Additionally, this sensor displayed remarkable durability and reusability, successfully completing penetration and signal acquisition in a simulated skin environment. This work presents a robust, multifunctional sensing strategy for the minimally invasive management of gout and other metabolic disorders, paving the way for future in vivo applications.
✓ 已验证
产品关联
DOI
高影响因子
RSC Advances
·
2026
·Vol. 16
·期 5
·4640-4654
·
IF 4.6
Yanping Zhang,Hong Xi,Dongyuan Qin,Ping Cao,Shuo Yang,Jing Yin,Tianliang Li,Lili Ding
Inflammatory bowel disease (IBD) is characterized by chronic gastrointestinal inflammation driven by oxidative stress and immune dysregulation. This study develops a novel oral nanozyme composite drug delivery system (MXene/CBN@GelMA, MCG) designed for targeted therapy of IBD. The composite integrates antioxidative MXene nanosheets and anti-inflammatory columbianadin (CBN) into a gelatin methacryloyl (GelMA) hydrogel, enabling targeted delivery and therapy. MCG efficiently scavenges reactive oxygen species (ROS) and generates oxygen (O2) through a superoxide dismutase (SOD)-catalase (CAT) cascade reaction, thereby alleviating oxidative stress and mitigating hypoxia in the inflamed tissues. In a dextran sulfate sodium (DSS)-induced IBD model, MCG treatment significantly reduced disease activity, restored colon length, preserved mucosal integrity, and suppressed pro-inflammatory pathways. Transcriptomic analysis revealed that MCG reversed IBD-associated gene expression dysregulation and modulated immune-related pathways. The system demonstrated high biocompatibility and effective targeting, providing a synergistic therapeutic strategy for IBD through antioxidative and anti-inflammatory mechanisms.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Sustainable Materials and Technologies
·
2026
·
IF 9.2
Peiyuan Li,Wenlin Zhou,Qing Guo,Siyan Liang,Chumei Liang,Wei Su
The development of multifunctional wound dressings from sustainable resources is critical to advancing green biomedical materials for effective wound repair. In this study, we present an eco-friendly microneedle delivery platform (LutCe-QCS-GP MN) with integrated reactive oxygen scavenging and antibacterial functions. The system features a sustainable nanozyme (LutCe), formed by self-assembly of the plant-derived flavonoid luteolin and cerium ions, which exhibits robust superoxide dismutase-like activity. These LutCe nanozymes organic-inorganic hybrids were synthesized through a green assembly process and demonstrate potent scavenging capability against superoxide anions, hydroxyl radicals, and reactive nitrogen species. Incorporated into the tips of the microneedles, they directly alleviate oxidative stress at the wound site. Simultaneously, an antimicrobial polysaccharide-based matrix provides effective defense against wound pathogens, preventing infection and secondary tissue damage. By synergistically combining sustainable antioxidant nanozymes with natural antibacterial components, the LutCe-QCS-GP MN system significantly reduced oxidative stress and bacterial load in wounds, markedly accelerating the healing process. Comprehensive in vitro and in vivo safety evaluations support the biosafety of the platform, underscoring its potential for clinical translation. This work not only introduces a promising therapeutic strategy for wound management but also highlights the valorization of natural, sustainable resources in functional material design, offering a meaningful reference for green technology applications in biomedicine.
✓ 已验证
产品关联
DOI
高影响因子
FUEL
·
2026
·
IF 7.5
Tao Ruan,Lifeng Li,Xinping Ouyang,Xueqing Qiu
Depolymerizing lignin is one of the most effective approaches for its high-valued utilization. However, the high oxygen contents in lignin depolymerized products cause the low calorific value, and hence limit their application in liquid fuels. A high efficiency 0.5 wt% Pd/WO x -ZrO 2 catalyst was designed and applied in the process for the depolymerization of lignin in this work. The effect of preparation methodology of catalyst support, the molar ratio of W to Zr, and Pd loading on both the structure of catalyst and catalytic activity to lignin depolymerization were investigated. It was found that the catalyst prepared by hydrothermal method exhibited a large specific surface area, more uniform distribution of supported Pd, as well as higher acid content and oxygen vacancies, which contributed a good catalytic activity. Moreover, the lower Pd loading and higher dispersion of Pd particles were beneficial for hindering the decrease in the specific surface area of the WO x -ZrO 2 support, and hence increasing the acidic sites of the catalyst, which also promoted both the cleavage of C-O bonds in lignin subunits and the alkylation of depolymerized products. When the catalyst prepared with 1:1 of W/Zr molar ratio and 0.5 wt% of Pd loading contributed to higher yields of bio-oil and aromatic monomers, achieving 83.30% and 35.49%, respectively. Among the aromatic monomers, 87.86% were demethoxylated alkylphenols, which significantly reduced the oxygen content of the depolymerization products.
✓ 已验证
产品关联
DOI
高影响因子
EUROPEAN JOURNAL OF PHARMACEUTICAL SCIENCES
·
2026
·
IF 4.7
Hong Shao,Wen Li,Zhuohan Li,Peng Shi,Zheng Li,Yuxiang Wang,Chao Pi,Lingmao Zhao,Wenwu Zheng,Yumeng Wei,Ling Zhao
Tegafur (FT) is widely used in the treatment of breast cancer. However, it has poor efficacy and significant toxic side effects. In this study, we first modified FT with aspirin to obtain a new FT derivative, named TAK5399. Then, TAK5399 in situ thermosensitive gel (TAK5399-TSG) was prepared using poloxamer F68 and F127 as carriers, and evaluated in vitro and in vivo. Among the five tested tumor cell lines, TAK5399 exhibited the highest sensitivity toward human breast cancer cells (MCF-7), with an inhibition rate 8.41 times higher than that of FT. Its potential anti-breast cancer mechanism may be related to inhibiting the PI3K/AKT signaling pathway to induce apoptosis and blocking the S phase of the cell cycle. The optimal formulation process for TAK5399-TSG is F127: 24.0%, F68: 6.5%, TAK5399 content of 1.25 mg/mL, and curing time of 24 hours. The maximum drug solubility, gelation temperature, and dissolution time were 1.25 mg/mL, 31 ± 0.21°C, and 6.5 ± 0.25 h, respectively. The Cmax of TAK5399-TSG administered via in situ injection was 15.5% and 23.8% of that of oral and in situ injection of TAK5399, respectively. In tumor-bearing mice, the tumor inhibition rates of oral TAK5399 and in situ injection of TAK5399-TSG were 1.28-fold and 1.82-fold higher than those of oral FT, respectively, with good biocompatibility. In conclusion, TAK5399-TSG is an in situ gel delivery system with potential for the treatment of breast cancer.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
Polymers
·
2026
·Vol. 18
·期 2
·195
·
IF 4.9
Mengyu Zhang,Wenqian Han,Mingfu Zhang,Yesheng Zhong,Liping Shi,Xi Chen
To address the low-value recycling dilemma of waste polyvinyl butyral (PVB) and cater to the demand for sustainable multifunctional active food packaging, this study developed a facile and cost-effective solution blow spinning approach. Continuous, smooth, and bead-free nanofiber membranes were prepared by optimizing the solution blow spinning process parameters. Zinc oxide nanoparticles (ZnO NPs) were incorporated into the PVB nanofiber membrane with vacuum impregnation. The results demonstrated that ZnO NPs significantly enhanced the tensile strength, thermal stability, and the UV absorption of PVB fiber membranes. ZnO/PVB fiber membranes exhibited antibacterial activity against Staphylococcus aureus , Escherichia coli , and Pseudomonas aeruginosa . Practical preservation tests showed that ZnO/PVB fiber membranes effectively inhibited cherry tomatoes’ microbial spoilage and water loss, extending the shelf life of tomatoes to 13 days. These findings validate the potential of ZnO/PVB composite nanofiber membranes as active food packaging and provide a feasible technical pathway for the low-cost, efficient utilization of recycled PVB.
✓ 已验证
产品关联
DOI
PubMed
高影响因子