CERAMICS INTERNATIONAL
·
2026
·
IF 5.6
Runrun Li,Mingdong Deng,Fusheng Song,Runhua Liao
In this study, a series of BaAl 12- x Ni x O 19-δ ( x =0, 0.2, 0.4, 0.6, 0.8, 1.0) blue pigments were successfully synthesized via a solid-state reaction method. The results confirmed that Ni 2+ ions successfully substituted Al 3+ within the host lattice without altering the crystal structure. The synthesized pigments exhibited a distinct blue hue, attributed to the characteristic d-d transition in Ni 2+ ions. Additionally, the pigments demonstrated high NIR solar reflectance (ranging from 68.08% to 98.82%) within the wavelength range of 700-2500 nm, which is markedly superior to traditional cobalt blue (39%). In a practical thermal insulation test, a ceramic body coated with the BaAl 11.6 Ni 0.4 O 19-δ glaze showed a remarkable surface temperature reduction of 21.66% compared to an uncoated substrate. The combination of excellent color stability in glaze and superior NIR reflectance makes this BaAl 12- x Ni x O 19-δ system a highly promising candidate for use as a cool pigment in energy-efficient building materials, such as reflective coatings for roofs and walls.
✓ 已验证
产品关联
DOI
高影响因子
Polymer Chemistry
·
2026
·
IF 3.9
Si-Ying Lan,Fuyue Tian,Xinyue Hao,Xin-Yu Li,Jing Bai,Nanying Ning,Bing Yu,Ming Tian
Liquid silicone rubber (SiR) exhibits significant application value in medical devices, flexible electronics, and soft robotics due to its excellent biocompatibility, tunable mechanical properties, and chemical stability. The additive manufacturing of SiR via 3D printing technology enables the customized fabrication of complex structures, particularly in multidisciplinary fields that require personalized designs, such as biomedical implants, bioinspired flexible sensors, and dynamically responsive soft robots. Despite the high precision achievable through stereolithography (SLA) or digital light processing (DLP) photocuring techniques, the low modulus of SiR remains a challenge for high-precision 3D printing. Inspired by the concept of polymer composites, blending SiR with mechanically robust polycaprolactone (PCL, a biocompatible polymer) provides an effective strategy to address these limitations, but still faces the challenge caused by the poor compatibility between SiR and PCL. In this study, a synergistic dual-compatibilization strategy was designed, amphiphilic compatibilizers (amino-functionalized carbon quantum dots, NH2-CDs) and modified polycaprolactone (PCL-DA) were introduced to enhance interfacial compatibility between the two phases. The introduced NH2-CDs, functioning as a nanoscale compatibilizer, effectively suppressed phase separation through interfacial Pickering stabilization, which resulted in a dramatic reduction of the dispersed SiR domain size from 25.94 ± 9.29 μm to 2.33 ± 0.55 μm, accompanied by the formation of a distinct interfacial layer (~860 nm). The resulting SiR/PCL-DA/NH2-CDs composite fulfills the requirements for photocurable 3D printing, achieving high precision, multi-morphological adaptability, and considerable mechanical performance. It exhibits considerable mechanical performance with a tensile strength of 440.7 kPa and an elongation at break of 367%. Additionally, the incorporation of semi-crystalline PCL and NH2-CDs endows the system with shape memory functionality (triggered at -5 °C and 60 °C) and fluorescence properties. This work presents a feasible approach for developing biocompatible, photocurable silicone elastomer-based composites via DLP 3D printing, offering broad prospects for advanced applications in smart materials and biomedical engineering.
✓ 已验证
产品关联
DOI
高影响因子
SEPARATION AND PURIFICATION TECHNOLOGY
·
2026
·
IF 9
Yu Zhang,Cuiyu Huang,Qiao Hu,Jingjing Hui,Xiwen He,Langxing Chen,Yukui Zhang
Fluoroquinolones residues pose direct threats to the ecological system and human health, hence it is important to effectively remove them from aqueous environment. In this work, a composite of bimetallic ZnCo-metal organic framework (MOF) functionalized electrospun polyacrylonitrile (PAN) nanofibers (ZnCoMOF@PAN) was prepared using room-temperature in situ growth approach for efficient adsorption of ciprofloxacin (CIP). The ZnCoMOF@PAN revealed well-defined crystallinity and exceptional BET surface area (1267.87 m 2 /g). The systematic adsorption studies (kinetics, isotherms, and thermodynamics) showed that the CIP adsorption process was spontaneous and the adsorption isotherms obeyed the Freundlich model, and the pseudo-second-order kinetics model could be well fitted to the adsorption behavior. Remarkably, the maximum adsorption capacity of ZnCoMOF@PAN to CIP can reach 872.32 mg/g, which is significantly higher than that of other reported adsorbents. In addition, the adsorption of CIP onto ZnCoMOF@PAN was dominated by a synergistic effect of multiple interactions: electrostatic attraction, hydrogen bonding, complexation, π-π stacking, and hydrophobic effects. Furthermore, the composite exhibited excellent adsorption selectivity, maintaining over 90% removal efficiency for CIP in various real water matrices. After 5 consecutive adsorption-desorption cycles, it still retained more than 90% of its original removal efficiency, demonstrating great potential for practical application in wastewater treatment.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2026
·
IF 13.2
Xingyu Gao,Ruihan Liu,Yao Li,Ran Cheng,Ruxia Liu,Jiaojiao Yu,Xuejun Zhang,Shao-Kai Sun,Quan Zou
Ultra-small melanin (USM) nanoparticles exhibit various unique advantages, including high specific surface area, good dispersibility, facile biodegradability, and limited liver and spleen accumulation, making them highly promising for theranostic applications. Nevertheless, the large-scale synthesis of USM nanoparticles through a simple method remains a daunting challenge. Herein, we propose large-scale synthesis of ultra-small naked melanin (USCM) nanoparticles by thermo-chemical degradation of cuttlefish melanin for theranostic applications in vivo . The USCM nanoparticles exhibit an ultra-small hydrodynamic diameter (6.8 nm), high purity, excellent solubility (up to 200 mg/mL), efficient metal ions (Mn 2+ /Cu 2+ /Fe 3+ /Gd 3+ ) chelation capacity, good antioxidant activity and photothermal capability. The longitudinal relaxivity of USCM-Mn nanoparticles is 41.74 mM −1 ·s −1 , 8.5-fold higher than clinical Gd-DTPA. For in vivo imaging, USCM-Mn nanoparticles enable precise magnetic resonance imaging of different kidney injuries and vascular diseases. For in vivo therapy, USCM nanoparticles allow for efficient in situ photothermal therapy of tumors. Notably, USCM nanoparticles can be directly used for in vivo theranostic applications without the need for special surface modifications ( e.g. , PEGylation). This study develops a simple yet effective approach for scalable melanin production, paving the way for its extensive utilization in biomedical applications.
✓ 已验证
产品关联
DOI
高影响因子
OPTICS AND LASER TECHNOLOGY
·
2026
·
IF 5
Junhui Yang,Yao Bai,Jing Yang,Can Yang,Peng Ye,Shan Gao,Jinhui Shi,Chunying Guan
External temperature and pH variations inevitably affect the measurement accuracy of the enzymatic biosensors. In order to solve this problem, a glucose biosensor with temperature and pH compensation was proposed and experimentally demonstrated. The biosensor is composed of a segment of hole-assisted three-core fiber (HATCF) and a segment of hole-assisted dual-core fiber (HADCF) in series and achieve three-parameter detection of glucose concentration, temperature and pH based on mode resonance coupling. One suspended core of the HATCF is functionalized with graphene oxide (GO)/glucose oxidase (GOD) for glucose concentration detection, and the other suspended core is utilized for temperature monitoring. The HADCF filled with polyacrylamide hydrogel is used to monitor pH change. This biosensor exhibits a linear response with a sensitivity of 6.82 nm/(mg/mL) under optimal reaction condition (T = 35 °C, pH = 7.0), enabling simultaneous glucose detection and monitoring of the reaction environment temperature and pH. The advantages of stable response, high selectivity, compact size, and three-parameter simultaneous detection make the proposed biosensor a significant candidate for its applications in multi-parameter sensing, environmental biomonitoring and real-time interference compensation detection.
✓ 已验证
产品关联
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2026
·
IF 5.6
Liwen Sun,Rong Li,Junjie Xu,Weiliang Jin,Jun Zhang,Hongmin Zhu,Saijun Xiao
Boron, owing to its excellent physicochemical properties, is utilized as a critical protective coating in numerous high-technology fields. However, conventional vapor deposition methods for fabricating boron coatings face inherent limitations, including low deposition rates, high costs, and the use of hazardous precursors. This paper, for the first time, proposes and successfully demonstrates a novel method for preparing amorphous boron coatings via molten salt electrophoretic deposition (MS-EPD). In a NaF-AlF 3 molten salt system at 970 °C, a fully dense, well-adherent, and thickness-controllable amorphous boron coating was successfully fabricated on a graphite substrate by employing boron nanopowder as the feedstock and systematically optimizing process parameters, particularly the electrophoretic voltage. It was found that the coating thickness initially increased and then decreased with rising voltage. A maximum thickness of 33 μm and an average growth rate as high as 29 μm/h were achieved, significantly surpassing those of conventional vapor deposition methods. The as-prepared amorphous boron coating also exhibited good interfacial bonding and excellent mechanical properties, with a critical load of 7.4 N and a nanoindentation hardness reaching up to 36.34 GPa. This study establishes MS-EPD as a highly efficient, cost-effective, and environmentally benign technology, opening a new avenue for the fabrication of high-performance, thick boron coatings.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF ANALYTICAL ATOMIC SPECTROMETRY
·
2026
·
IF 3.1
Peng Zhu,Miaomiao Wang,Dongdong Li,Chang Liu,Zhengbo Qin,Zefeng Hua,Zhong-Fa Sun,Xinyan Yang,Xianfeng Zheng
Plasma amplification laser-induced breakdown spectroscopy (Plasma amplification LIBS) has shown great potential in N elements in water due to high sensitivity, precision, and accuracy. To further reduce interferes of the atmospheric nitrogen, the effect of laser wavelength on the quantitative determination of nitrogen in water was investigated. With short laser wavelength, stronger spectral line intensity, lower interference from atmospheric nitrogen, and superior analytical performance were obtained. The linear coefficient of determination (R²) of the calibration curve improved from 0.2147 to 0.9732, the limit of detection (LOD) was reduced from 18.98 ppm to 3.41 ppm, and the spectral stability, expressed as average relative standard deviation (RSDAV), was reduced from 10.49% to 5.45%. Moreover, the average relative error (REAV) and the root mean square error of cross-validation (RMSECV) for the predicted concentrations were improved by approximately 56.82% and 71.79%, respectively. These results demonstrate that the 532 nm wavelength in plasma amplification LIBS can significantly enhance both the detection sensitivity and the accuracy of quantitative analysis for nitrogen in water.
✓ 已验证
产品关联
DOI
高影响因子
SENSORS AND ACTUATORS B-CHEMICAL
·
2026
·
IF 7.7
Yixue Chen,Huaiyu Song,Yan Qin,Yu Liu,Ying Xie,Zhenyu Chu,Wanqin Jin
Pyruvate is one of the most important intermediate metabolites in the fermentation process, thereby making it a potential indicator for monitoring and regulating the fermentation process. Since the fermentation broth is usually complex, including microorganisms, various ions, organic compounds, etc., it is necessary to develop a highly selective method for detecting pyruvate. Therefore, in this work, we proposed an ultrasensitive electrochemical enzymatic biosensor for pyruvate determination at a low working potential through constructing Prussian blue@Au nanoframes (PB@Au NFs) with improved conductivity and high electrocatalytic ability. Due to the strong catalytic ability of PB nanoframes for the reduction of H 2 O 2 , the as-prepared sensor initially demonstrated extremely 2.7-fold sensitivity toward H 2 O 2 than the non-frame structured PB nanocubes. Furthermore, after the conditions for pyruvate detection were systematically optimized, the fabricated sensor was able to effectively identify pyruvate ranging from 5 μM to 0.895 mM at -0.2 V which represented an orders-of-magnitude improvement in sensitivity over existing sensors. Meanwhile, the low working potential and the highly precise recognition ability of pyruvate oxidase ensured the high selectivity of the prepared sensor, and the sensor also showed excellent reproducibility and long-term stability. Finally, our biosensor was employed to detect pyruvate in the real microbial fermentation liquid, giving an excellent accuracy with RSD values of 1.44% - 4.64%. This work provides a new strategy approach for the design and establishment of stable pyruvate sensors and offered a usefulness approach for the pyruvate detection with high performance.
✓ 已验证
产品关联
DOI
高影响因子
NEW JOURNAL OF CHEMISTRY
·
2026
·
IF 2.5
Qi Liu,Tianyou Chen,Xiaorong Xiong,Yizhuo Lu,Wen Fan,Zushun Xu
The development of photoredox catalysis in water allows access to green and sustainable organic synthesis. Acridinium salts are entirely organic, powerful, inexpensive, and environmentally friendly photocatalysts, but most of them have poor solubility in aqueous media, leading to a lack of control over their sizes and morphologies that play an important role in catalytic performance. To tackle this challenge, here we have devised an effective strategy for the preparation of acridinium-based photoredox nanocatalysts with controllable size and morphologies in water by using mixing-induced nanoprecipitation (MINP). These catalytic systems could be utilized for site-selective arene C–H amination in water under open air. To inhibit the degradation of acridinium salts, 2,2,6,6-tetramethylpiperidin-1-oxyl (TEMPO) was incorporated for the enhancement of catalytic performance. Moreover, a TEMPO-containing polymer was synthesized for the co-immobilization of an acridinium salt and TEMPO to facilitate their recovery and reuse. As a proof-of-concept, this work may open up an avenue for the development of photoredox nanocatalysts with controllable size and morphologies and for their co-immobilization with other catalytic components.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF COLLOID AND INTERFACE SCIENCE
·
2026
·
IF 9.7
Chun Sun,Jiazhi Cui,Zhengtao Qiu,Jiabao Bai,Chao Fan,Dan Huang,Guohua Jia
Perovskites have attracted considerable interest as potential photocatalysts for sustainable hydrogen generation. Nonetheless, their intrinsic instability in aqueous media significantly constrains their practical deployment in photocatalytic hydrogen evolution. To address this challenge, we propose a versatile strategy for stabilizing Cs 3 Bi 2 Br 9 (CBB) perovskite photocatalysts through combining zwitterionic ligand encapsulation with Sn 4+ doping. The zwitterionic ligand, synthesized by reacting 4-bromobutyric acid (BBA) with oleylamine (OLA), was employed to passivate the perovskite surface by anchoring to both Bi 3+ and Br − sites, effectively mitigating surface defects. Notably, Sn 4+ doping is essential for aqueous stability, as the incorporation of Sn 4+ not only enhances the intrinsic stability of CBB but also reinforces the binding affinity of surface ligands. As a result, the Sn 4+ -doped CBB (CBBS x ) with ligand encapsulation demonstrates remarkable stability, retaining its structural integrity in water for over six months and withstanding more than three cycles of photocatalytic testing. Importantly, this strategy demonstrates considerable generality, as it can be readily extended to the synthesis of other halide perovskites. Specifically, the MoS x -loaded Sn 4+ :Cs 3 Bi 2 Br x I 9-x (MoS x /CBBIS 0.2 ) composite achieves a remarkable hydrogen evolution rate of 18.2 mmol h −1 g −1 , which represents the highest performance reported to date among Bi-based perovskite photocatalysts.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
DRUG METABOLISM AND DISPOSITION
·
2026
·
IF 4
Jiye Tian,Jiarui Zhang,Zihan Tang,Chunpeng Feng,Yue Deng,Jiale Liu,Shuang Feng,Xinyue Zhou,Lei Yin,Meiyun Shi
A comprehensive understanding of the in vivo fate of low-molecular-weight polyethylene glycol (PEG) oligomers is essential for optimizing PEGylated therapeutics. This study delineates the polymerization-dependent absorption, distribution, metabolism, and excretion (ADME) of discrete PEG600 oligomers (n = 9–18) in rats using a validated UHPLC-MS/MS method. Systemic exposure, assessed by dose-normalized AUC, was highest for shorter oligomers (n = 9–10) and declined for longer chains (n ≥ 17), while all oligomers exhibited similarly short terminal half-lives (12.7–15.2 min), indicating rapid elimination irrespective of chain length. Tissue distribution revealed pronounced renal accumulation, peaking at mid-chain lengths (n = 11–13), consistent with size-dependent glomerular filtration and tubular reabsorption. Oxidative metabolism yielded both mono- and di-carboxylated derivatives, confirming active enzymatic processing. Excretion studies demonstrated chain-length-dependent elimination, with reduced recovery of longer oligomers suggesting substantial in vivo biodegradation. These findings provide the first monomer-resolved ADME profile of PEG600 oligomers, highlighting the critical role of polymerization degree in governing their pharmacokinetics and informing the rational design of PEGylated drug formulations.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
SENSORS AND ACTUATORS B-CHEMICAL
·
2026
·
IF 7.7
Zhe Yu,Rui Tang,Minyu Wu,Wenke Zou,Muxuan Chang,Hongqin Mao,Jinyuan Liang,Xiaohui Xu,Cheng Zhang,Fadi Chen
Phosphorus is an essential macronutrient governing key physiological traits in chrysanthemum. However, phosphate nutrition is typically evaluated based on fertilizer input rather than direct in planta uptake, limiting management accuracy. Here, we develop a miniaturized electrochemical microprobe array for direct in planta detection of phosphate in chrysanthemum stem sap. The array integrates a cobalt-based working electrode fabricated via an electroplating-then-etching technique and a titanium-based iridium dioxide reference electrode, all optimized for miniaturization and biocompatibility. The array demonstrated a wide linear detection range (10−5 to 10−1mol/L), good sensitivity (41 mV/dec), and strong anti-interference performance in the presence of coexisting ions. Biocompatibility tests confirmed minimal disruption to plant growth after short- and long-term probe implantation. In planta measurements revealed spatial variation in phosphate distribution along the stem and dynamic uptake responses following fertilizer application. These findings highlight the potential of this microprobe array for precise nutrient uptake analysis and sustainable phosphorus management in horticultural systems.
✓ 已验证
产品关联
DOI
高影响因子