文献检索

查找使用阿拉丁产品的科研文献

检索与阿拉丁产品相关的同行评审论文、DOI、PubMed 编号、期刊、作者、CAS 号及研究领域。

科研影响力快照

与阿拉丁产品相关的已发表科研成果

在搜索之前,这些指标可帮助访客快速了解产品关联科研的规模与质量。

347,389+ SCI 论文 与阿拉丁产品引用相关
2,303,681.05 总影响因子 匹配文献记录中影响因子的总和
81.20 最高期刊影响因子 匹配期刊中的最高 IF
6.63 平均期刊影响因子 匹配文献的平均 IF

参考指标 指标基于阿拉丁文献引用数据库及期刊影响因子记录。文献关联仅供科研参考,请以原始文献为准。

产品列表

视图 列表 网格

显示第1141至1152个,产品总数347,389个

切换升序
Journal of Building Engineering · 2025 · IF 7.4

Effect of calcium formate on microstructure and mechanical properties of strain-hardening CaO-activated GGBFS composites

Min-Chang Kang,Taekgeun Oh,Goeun Jun,Doo-Yeol Yoo,Sukhoon Pyo

This study investigated the effects of calcium formate as an accelerator in newly developed CaO-activated strain-hardening cementless composites (SH-CASC). Six doses of calcium formate, ranging from 0 to 5 % by weight of ground granular blast furnace slag (GGBFS) and calcium oxide, were tested. Thermogravimetric analysis, mercury intrusion porosimetry, hydration heat tests, compressive tests, single fiber pullout tests, direct tensile tests, and life cycle assessment (LCA) analyses of the SH-CASC were performed. The experiment results indicated that the incorporation of calcium formate enhanced the compressive strength of SH-CASC. Furthermore, calcium formate improved the bond strength between the matrix and fiber, resulting in higher tensile strength, strain capacity, and strain energy density. SH-CASC also showed a lower environmental footprint, with reduced carbon dioxide emissions and health hazards than cement- and cementless-based strain-hardening composites. Thus, SH-CASC presents a sustainable and promising composite material in the field of construction with good mechanical properties and environmental effects.

CAS / MDL: 544-17-2
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
CERAMICS INTERNATIONAL · 2025 · IF 5.6

Effects of TiO2 doping and sintering temperature on electrical, mechanical and thermal properties of Al2O3 ceramics

Minghui Sun,Xiangqian Quan,Xi Ma,Hetuo Chen,Xianpeng Qin,Guohong Zhou

The effects of TiO 2 content and sintering temperature on the electrical and mechanical properties of the alumina ceramics prepared via vacuum sintering were investigated. The sample comprises the phases of Al 2 O 3 , MgAl 2 O 4 , and Al 2 TiO 5 . Under vacuum sintering conditions, oxygen atoms in TiO 2 detach from the crystal lattice, forming quasi-free electrons, oxygen vacancies and Ti 3+ , thereby reducing the volume resistivity of alumina ceramics. XPS (X-ray photoelectron spectroscopy) analysis revealed that the increasing TiO 2 content facilitates the transformation of Ti 4+ to Ti 3+ , while elevated sintering temperatures further enhance Ti 3+ concentration, attributed to the enhanced lattice activity of TiO 2 . The increasing TiO 2 generated more Al 2 TiO 5 with Al 2 O 3 , which accumulated at grain boundaries, inhibiting grain growth through a pinning effect and forming more uniform and smaller grains, thereby enhancing mechanical property. Optimal comprehensive properties were achieved at a sintering temperature of 1500°C with 6 % TiO 2 content, demonstrating a density of 3.88 g/cm 3 , volume resistivity of 1.2×10 11 Ω·cm, dielectric strength of 3.6×10 6 V/m, hardness of 14.4 GPa, and thermal conductivity of 17 W/(m·K). The series of outstanding performances confirm that Al 2 O 3 ceramic with TiO 2 doping is an excellent candidate material in advanced semiconductor processing.

CAS / MDL: 1309-48-4 13463-67-7
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
CERAMICS INTERNATIONAL · 2025 · IF 5.6

Removing lattice oxygen and manipulating the microstructure to obtain high thermal conductivity aluminum nitride ceramics

Fei Ying,Jiayi Shan,Xingen Xie,Le Sun,Ziwen Shi,Yongjie Xie,Gaoyang Fang,Wu Lei,QingLi Hao

Aluminum nitride (AlN) ceramics are ideal for high-power electronic packaging; however, their thermal conductivity in industrial applications remains far below the theoretical value of 320 W m −1  K −1 , a limitation primarily attributed to lattice oxygen-induced defects and suboptimal microstructures. To address this, a scalable tape casting-pressureless sintering process was developed, optimizing thermal performance by regulating yttria (Y 2 O 3 ) doping content (1–10 wt%), sintering temperature (1720–1840 °C), and isothermal holding time (1–4 h). Mechanistically, 5 wt% Y 2 O 3 purifies the lattice oxygen through the formation of Y 4 Al 2 O 9 (YAM), promotes the migration of secondary phases to triple junctions, and facilitates the formation of uniform grains, effects that synergistically suppress phonon scattering. Under optimal parameters (1800 °C, 3 h isothermal holding), the fabricated AlN ceramics achieved a thermal conductivity of 194.8 W m −1  K −1 and a bending strength of 458 MPa. This study combines scalable fabrication, elucidated regulatory mechanisms, and balanced material properties, offering a novel route for the industrial production of high-thermal-conductivity AlN ceramics, thereby supporting advanced thermal management in 5G and new energy sectors.

CAS / MDL: 122-32-7 67-64-1 78-93-3
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
CHEMICAL ENGINEERING SCIENCE · 2025 · IF 4.3

Construction of S-scheme high-entropy layered double hydroxides nanosheets/carbon nitrides nanotubes heterojunction for various pollutants removal by photocatalytic peroxymonosulfate activation

Jintao Dong,Jing Hong,Zhishuai Wang,Pengjun Liu,Gaopeng Liu,Lina Li,Shengqun Cao,Bin Wang,Jiexiang Xia

For achieving the broad-spectrum removal ability of g-C 3 N 4 materials for various contaminants, it is assessed as critical core by synchronously enhancing the solar absorption-conversion and PMS adsorption-activation process of g-C 3 N 4 materials. In this manuscript, S-scheme high-entropy FeMnCoNiCu-LDHs/self-assembly carbon nitride nanotubes (LDHs/SCN) heterojunction were established by mechanical-assisted ball milling, calcination, and hydrothermal method. Contributed to the synergistic effect of multi-metal elements in FeMnCoNiCu-LDHs materials, the photocatalytic PMS activation efficiency of LDHs/SCN composites is benefit from the efficient conversion of Fe 3+ /Fe 2+ , Mn 4+ /Mn 3+ , Co 3+ /Co 2+ , Ni 3+ /Ni 2+ , and Cu 2+ /Cu + redox cycles. So, under 0.1 mM PMS and visible light irradiation, the removal efficiency of bisphenol A (BPA), ciprofloxacin (CIP), 2-mercaptobenzothiazole (MBT), oxytetracycline (OTC), tetracyclines (TC), and sulfadiazine (SD) pollutants in LDHs/SCN-0.2/PMS/Light system reach to 91.1 %, 82.8 %, 94.7 %, 86.8 %, 91.4 % and 63.0 %, respectively. Furthermore, the enhancement mechanism of the photocatalytic PMS activation performance of LDHs/SCN-0.2/PMS/Light system has been elucidated through ESR, UPS, ROS quenching experiments, and band structure analysis. The LC-MS and T.E.S.T. software was successively employed for intermediates transformation pathways and bio-toxicity during BPA degradation. Consequently, this work lays a foundational basis for the design and construction of highly efficient S-scheme heterojunctions for advanced wastewater purification.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
CARBON · 2025 · IF 11.6

Design and application of ratiometric room temperature phosphorescent probes based on triplet-singlet Fӧrster resonance energy transfer mechanism between silica-coated phosphorescent carbon dots and rhodamine 6G

Yuxin Zheng,Kamile Arkin,Yuting Xu,Xue Jiang,Ning Xu,Qingkun Shang

In this paper, we successfully designed and constructed a ratiometric room temperature phosphorescent probe (CDs@SiO 2 –Rh6G) that can realize highly sensitive detection of nitrite in urine under the interference of ascorbic acid (AA) based on the triplet-to-singlet Fӧrster resonance energy transfer mechanism between silica-coated phosphorescent carbon dots and rhodamine 6G. This unique energy transfer mechanism is discussed in detail, and the interference of various factors on nitrite detection is systematically investigated. With the successful masking of AA by 4-hydroxy-2,2,6,6-tetramethylpiperidinooxy (4-OH-TEMPO), CDs@SiO 2 –Rh6G could accurately detect NO 2 − with a limit of detection (LOD) as low as 0.242 μmol/L, which is much lower than that of the commercially available urinary nitrite test paper. The probe was tested on real urine samples—human, dog, and cat urine—and the results were highly consistent with those obtained by ion chromatography, with spike recoveries ranging from 96.5 % to 105.3 %. Since the green and yellow luminescence of the probe is visible to the naked eye, a visual analysis method based on the RGB values of smartphones was developed. This study presents a new strategy for constructing ratiometric room temperature phosphorescent probes based on a unique TS-FRET mechanism. Meanwhile, this research not only overcomes the quantitative limitations of current test strip detection methods but also lays the foundation for developing more sensitive and accurate clinical diagnostic tools for urinary tract infections.

CAS / MDL: 2226-96-2
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF PHOTOCHEMISTRY AND PHOTOBIOLOGY A-CHEMISTRY · 2025 · IF 4.7

The Mars–van Krevelen cycle and fine-customized d-band centers promoting S-scheme heterojunction charge transfer on wide solar-spectrum photocatalytic water purification

Zhiqiang Yu,Yufan Lan,Tenghui Li,Shucheng Huang,Wuli Han,Xiao Luo

This study constructed an S-scheme MIL( Fe )DCA (et al., 2023b (6)) /MoS 2 heterojunction for enhanced performance in degrading pollutants under a wide spectrum, benefiting from the customized d-band centers (by the built-in electric field) and the Mars–Van Krevelen cycle. Results reveal the tetracycline degradation rate of MIL( Fe )DCA (et al., 2023b (6)) /MoS₂ (~95 %) increases 1.38-fold and 11.8-fold compared to pristine MIL-Fe-DCA and MoS 2 , respectively, with better repeatability.Also, satisfactory reduction of Cr(VI) ions (75 %) and removal of coumarin (81.3 %) and ciprofloxacin hydrochloride (83 %) are observed. The catalyst exhibits rich defects, wide-spectrum solar light harvesting, efficient separation of h +  ~ e − pairs and a robust redox process. It is found that the charge transfer in the S-scheme interfacial electric field elevates the d-band center towards the Fermi level, which can effectively lower water activation energy to more easily produce •OH, enhancing intermediate adsorption on the catalyst's surface, thus facilitating charge transfer and accelerating reaction kinetics. Another major emphasis is the oxygen defects induced Mars–Van Krevelen cycle, wherein adsorbed reactants, lattice oxygen, h + , •O 2 − , Fe 2+ and Fe 3+ participate in the reaction processes, which contributes to the photo-thermal conversion, achieving the synergy between photocatalysis and photothermal catalysis. This work offers a synergetic strategy involving the interfacial electric field, d-band center, and photo-thermal effect for photocatalytic water purification.

CAS / MDL: 64-17-5 7697-37-2
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF CHROMATOGRAPHY B-ANALYTICAL TECHNOLOGIES IN THE BIOMEDICAL AND LIFE SCIENCES · 2025 · IF 2.8

Preparation of sodium alginate-based temperature- and pH-responsive MOF/hydrogel microspheres and their adsorption and separation of proteins

Zhikun Li,Yuanyuan Li,Yulong Ma,Wenxin Ji,Yonggang Sun

The purification of biomacromolecules, particularly proteins, plays an increasingly vital role in the fields of medicine, biopharmaceuticals, and emerging technologies. Adsorbents with excellent adsorption capacity, superior cycling performance, and environmental compatibility are crucial for protein separation and adsorption. A temperature- and pH dual-stimulus responsive hydrogel material for the adsorption and separation of protein was successfully prepared by copolymerizing sodium alginate (SA) as the matrix with N-isopropylacrylamide (NIPAM), acrylic acid (AAC), and simultaneously introducing zirconium-based metal-organic frameworks (Zr-MOF). This hydrogel material exhibits excellent adsorption and controlled release properties for protein including bovine hemoglobin (BHB) and bovine serum albumin (BSA) with maximum adsorption capacities of 617.45 mg/g and 527.06 mg/g at 45 °C, respectively. Experimental results demonstrate that the adsorption and release behavior of the hydrogel toward proteins can be effectively regulated by adjusting environmental temperature or pH value in an aqueous medium without any acidic, alkaline, high-salt, or organic solvent. Additionally, the material exhibits good cyclic stability, maintaining more than 85 % of its initial protein adsorption capacity after five adsorption-desorption cycles. This study provides new insights into the development of smart responsive biomolecular adsorption materials and has significant application potential in the fields such as drug controlled release and biological separation.

CAS / MDL: 10043-52-4 9005-38-3
✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
DENTAL MATERIALS · 2025 · IF 6.3

One-step vs. two-step deposition of CaF2 nanoparticles: From the perspective of confined water release and bonding effectiveness improvement

Jiajia Xu,Yanji Lu,Kai Zhang,Qiaojie Luo,Xiaodong Li

Objective To compare the bonding efficacy of one-step versus two-step calcium fluoride (CaF₂) nanoparticle deposition and to elucidate the underlying mechanisms. The null hypotheses tested are as follows: 1) Nanoparticles deposited via the one-step strategy are less uniformly distributed than those deposited via the two-step strategy; 2) The one-step strategy does not release more confined water compared to the two-step strategy; 3) The one-step strategy is inferior to the two-step strategy in enhancing dentin bonding durability. Methods A stable amorphous calcium fluoride (ACF) precursor solution was prepared by mixing 10 mM CaCl₂ and 10 mM NaF in 20 mM HEPES buffer for 20 s, enabling one-step CaF₂ nanoparticle deposition through the mineralization-regulating function of non-collagenous proteins acting as pseudonuclei. The two-step strategy consisted of sequentially applying 0.1 M CaCl₂ and 0.2 M NaF, each for 20 s. Neutralization of matrix negative charges, reduced hydration capacity, and confined water release were assessed via cationic dye adsorption, zeta potential, water contact angle, ATR-FTIR spectroscopy, and thermogravimetric analysis. Interface characteristics were evaluated using SEM, TEM, and XPS. Bonding effectiveness was determined by adhesive infiltration depth, micro-tensile bonding strength (μTBS), and nanoleakage expression, both initially and after aging. Results Our results demonstrate that the one-step strategy produces smaller, more homogeneous nanoparticles that penetrate collagen fibrils more effectively. We thus reject the null hypothesis 1. Compared to the unmodified demineralized dentin matrix (DDM), the DDM obtained with the two-step approach exhibits reduced interfacial water, which further reduced by the one-step strategy. The null hypothesis 2 is thus rejected. Compared to the conventional wet-bonding control (AW), bonding performed on these optimized DDM leads to enhanced adhesive infiltration. Both one-step (ACF) and two-step strategies (CW) improve the immediate bonding strength (43.00 ± 4.15 MPa and 36.81 ± 3.32 vs. 31.57 ± 2.02 MPa). after 12 months of storage in water at 37 °C, bonding strength of the AW group significantly decreased to 26.92 ± 2.35 MPa (p < 0.05), whereas the CW group decreased to 30.20 ± 4.66 MPa (p < 0.05) and the ACF group maintained a high level (39.22 ± 5.12 MPa, p > 0.05). Significance This novel one-step dentin bonding strategy effectively addresses the challenge of dentin bonding durability. By simultaneously reduced electronegativity, lower hydration capacity, decreased confined water, enhanced mechanical properties, and reinforcement at the basal level, adhesive infiltration was improved, clinical procedure was simplified, and bond durability was sustained provided. The one-step dentin bonding strategy offers a clinically practical, time-efficient, and superior alternative for durable resin-dentin bonds.

✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
DIAMOND AND RELATED MATERIALS · 2025 · IF 5.1

In-situ constructed core-shell SiO2@f-PPy/MXene hybrid epoxy coating for anticorrosion and antistatic protection of magnesium alloys

Xiangjun Li,Yuxin Shi,Miaomiao Li,Shengwei Deng,Yinxia Dong,Libo Tong,Zhongze Du,Kuaishe Wang

The exceptional protection of epoxy resin (EP) is restricted in practical applications due to high electrical insulation and inherent microporous defects. In this study, acid-doped polypyrrole (f-PPy)/MXene hybrid nanomaterials incorporated into the EP matrix to construct three-dimensional (3D) conductive network that simultaneously enhances corrosion resistance and imparts antistatic capability. Electrochemical impedance measurements demonstrate a long-term stability, maintaining 9.73 × 10 10  Ω cm 2 even after 14 days of immersion, which is significantly higher than the EP coatings. Compared with pure EP, the composite SiO 2 @f-PPy/MXene/EP coating shows a 3 times reduction in surface resistivity (8.68 × 10 7  Ω m) and exceeds the industrial antistatic threshold by two orders of magnitude. The enhanced anticorrosion is attributed to the synergistic contribution of the triple properties of the SiO 2 @f-PPy/MXene: “labyrinth effect”, redox effect and corrosion inhibition. SiO 2 @f-PPy/MXene 3D conductive network enhances the antistatic ability of EP. This dual-functional strategy addresses the critical gap of combining anticorrosion and antistatic performance in EP coatings and offers a practical route for protective applications on Mg alloys.

CAS / MDL: 109-97-7 7631-86-9
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
Journal of Environmental Chemical Engineering · 2025 · IF 7.2

Preparation and characterizations of slow-releasing humic acid fertilizer loaded in starch-based hydrogel

Litao Ma,Jiabao Bai,Long Yu,Qingfei Duan,Yue Song,Zhongjie Tang,Fengwei Xie,Zhongxian Li,Xiaodan liu,Xuejun Yu,Deyi Xie

Eco-friendly slow-release humic acid fertilizers (SRF-HAs) with water retention function were fabricated by in situ radiation polymerization through grafting of acrylic acid (AA) or acrylamide (AM) on cornstarch containing surface coated HAs. The balance of properties between water retention and HA loading was optimized on the basis of performance in saline-alkali soil. The SRF-HAs were characterized by FTIR, NMR, SEM, Rheometer, and measurement of water retention and release behavior. The quantities of both grafting and conversion ratios were determined based on TGA measurements. The performance of SRF-HAs was evaluated by cotton germination in both normal and saline-alkali soils. Chemical characterizations (FTIR and NRM) confirmed the successful grafting of polyacrylic acid (PAA) and polyacrylamide (PAM) onto starch. The AA and AM graft ratios on the starch achieved approximately 82.57 and 80.74% respectively. The water retention capability in soil was increased about seven times after adding the hydrogel-based fertilizer for 15 days. The potassium release rate (indicating HA) was significantly slowing (approximately 62.1%) in SRF-HA. Comparative analysis of fertilizer placement strategies (upper, medium and lower layers in soil) revealed that mid-layer incorporation achieved the best enhancement, which increased germination rates from 9.4% to 62.5%. This achievement is principally attributable to the capacity of SRF-HA to keep moisture and equilibrate pH in saline-alkali soils. The fertilizer from the starch grafted AA series consistently demonstrated higher germination rates compared to that grafted with AM series, possibly attributed to abundant carboxyl groups within the PAA chains that effectively mitigate soil alkalinity and stimulate seedling emergence.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF PHARMACEUTICAL SCIENCES · 2025 · IF 3.8

Investigation of CT imaging-based Bi2S3 drug-loaded nanoparticles for the diagnosis and therapy of colorectal cancer

Qian Lu,Benhan Zhang,Hao Zhang,Jianlei Xue,Wenbo Duan,Yonggang Wan,Datong Chen,Jie Wang,Xu Guo,Liping zhang

Colorectal cancer ranks as the third most prevalent cancer globally, with its incidence increasing in many developed countries. While chemotherapy demonstrates efficacy for certain patients, it is associated with significant side effects, and prolonged treatment may result in drug resistance. Consequently, this study synthesized Bi 2 S 3 nanosheets via the solution-based method and integrated them with mesoporous silica exhibiting excellent pore channel properties to develop the Bi 2 S 3 @mSiO 2 -PEG/5-FU nanomaterials. Photothermal testing revealed that Bi 2 S 3 @mSiO 2 -PEG/5-FU exhibited superior photothermal heating performance, remarkable photothermal stability, and a photothermal conversion efficiency of 28.3%, enabling effective photothermal therapy. The drug loading capacity of Bi 2 S 3 @mSiO 2 -PEG/5-FU was determined to be 24.8%, with enhanced drug release under acidic conditions and laser irradiation, thereby improving chemotherapeutic efficacy and achieving synergistic effects between chemotherapy and photothermal therapy. Furthermore, Bi 2 S 3 @mSiO 2 -PEG demonstrated robust CT imaging capabilities (14.95 HU mg/mL), establishing the Bi 2 S 3 @mSiO 2 -PEG/5-FU nanomaterials as a platform with integrated diagnostic and therapeutic functionalities.

✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
BIORESOURCE TECHNOLOGY · 2025 · IF 9

Phytoremediation of antibiotics and antibiotic resistance genes (ARGs) by submerged macrophytes: Synergistic removal and mechanistic insights

Huimin Wei,Lu Zhang,Yujie Mao,Yiting Cheng,Cong Wang,Zhi Wang

Antibiotic resistance genes (ARGs) pose a major threat to human disease control and have emerged as a critical global public health concern. While aquatic plants are widely recognized for removing antibiotics, their efficacy in co-removing ARGs and underlying mechanisms remain poorly understood. To fill this gap, we systematically evaluated the removal effects and mechanisms of enrofloxacin (ENR), tetracycline (TC), sulfamethoxazole (SMX) and associated ARGs and mobile genetic elements (MGEs) by Hydrilla verticillata , a widespread aquatic macrophyte. Compared with controls without plant, H. verticillata significantly enhanced TC, ENR, and SMX removal efficiencies by 7.8 %, 38.1 %, and 8.5 %, respectively. Concurrently, it reduced the abundance of ARGs and MGEs by 7.21–86.8 %, confirming its novel dual co-removal function. Notably, plant uptake contributed only 0.03–6.3 % to antibiotic removal. Instead, removal relied on H. verticillata -mediated microbial regulation: mitigating antibiotic-induced microbial detriment, maintaining diversity, and enriching degrading bacteria. We further found that aquatic plants alleviated the risk of ARG dissemination by enhancing microbial diversity, narrowing the potential host range, and simplifying ARG transmission networks. Critically, partial least squares path modeling revealed that MGEs were the primary drivers of ARGs dynamics in treatments with plant (path coefficient: 0.840), whereas antibiotic selection pressure dominated without plant (path coefficient: 0.875). These findings highlight the dual role of H. verticillata in antibiotic removal and ARG suppression, providing novel insights into phytoremediation as a sustainable strategy for restoring antibiotic-contaminated aquatic environments and combating antimicrobial resistance.

✓ 已验证 DOI PubMed 高影响因子
查看原文 查看 PubMed
已复制

文献关联基于可获得的产品、CAS、DOI 及引用记录。收录不代表作者或出版方对阿拉丁产品的背书,请以原始文献为准。