Journal of Water Process Engineering
·
2026
·
IF 6.6
Zhengqi Liang,Xiongyan Gao,Yushan Li,Xu Liu,Boxing An,Yingying Zuo,Ling Wang,Jiahui Fu,Meili E
Staged modification significantly improved the adsorption capacity of BC. • The adsorption capacity of Zn-La@BC is 11.28 times that of the original BC. • Zn-La@BC retains 80% of its adsorption capacity after 5 cycles. • Zn-La@BC exhibits strong resistance to interference from low-valent ions. • Metal complexation and electrostatic interactions are the primary mechanisms. A Zn La co-doped reed biochar (BC) adsorbent was prepared using a staged optimization and a two-step bimetallic modification method to enhance its adsorption capacity for tetracycline hydrochloride (TC). The optimal process conditions for the Zn La co-doped biochar (Zn-La@BC) adsorbent were determined using the response surface method (BBD): Calcination at 300 °C for 120 min under N 2 protection with a Zn@BC to LaCl 3 mass ratio of 1:0.6. Maximum adsorption occurred at a pH of 9, a dosage of 0.20 g·L −1 , and a reaction temperature of 35 °C. Fitting the Langmuir model revealed a maximum adsorption capacity of 594.65 mg·g −1 , which is an 11.28-fold increase on pristine BC. This adsorbent exhibit strong resistance to low-valent ion interference, retaining 80% adsorption capacity after 5 cycles and demonstrating excellent cyclic stability. Its adsorption mechanism primarily involves metal surface complexation and electrostatic adsorption, supplemented by hydrogen bonding, π-π interactions, and pore filling. This study provides a novel approach for preparing high-capacity reed-derived BC adsorbents.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2026
·
IF 12.5
Liang Zhang,Ziwei Chen,Jing Chen,Yu Sun,Yue Wang,Jiadeng Zhu,Qiang Gao,Peizhi Zhu,Chunxia Gao
A green ternary solvent system (Na 2 SO 3 /LiCl/urea) is developed to overcome the poor water solubility of wheat gluten. • Self-helical wheat gluten fibers are continuously fabricated via a one-step wet-spinning process. • The fibers exhibit excellent stretchability (1200% elongation), ionic conductivity, and excellent anti-freezing performance down to −80 °C. • The fibers enable real-time monitoring of human motions, respiratory behaviors, and Morse-code-based information transmission. • A smart glove system is demonstrated for closed-loop human-machine interaction using the helical fibers. With the rapid advancement of wearable intelligent electronics, various high-performance conductive fibers have been developed. However, most of them suffer from an inherent trade-off between electrical stability and mechanical deformability, often failing to maintain consistent conductivity under large or repeated mechanical strain. Inspired by natural helical architectures, wheat gluten (WG) conductive fibers with a self-helical architecture have been successfully developed via a facile wet-spinning technique. To address the intrinsically poor water solubility of pristine WG, a ternary solvent system consisting of Na 2 SO 3 , LiCl, and urea is developed. Continuous self-helical WG fibers are obtained by extruding the spinning dope into a 20 wt% Na 2 SO 4 coagulation bath. The resultant fibers exhibit exceptional mechanical flexibility (with an elongation at break of 1211 ± 85% and a tensile strength of 12.8 ± 1.5 MPa), outstanding anti-freezing performance (stable performance at −80 °C), ionic conductivity (1.59 ± 0.25 mS/m) and distinct humidity-responsive behavior. When assembled into flexible sensors, they enable reliable real-time monitoring of diverse human motions, subtle respiratory signals, and efficient human-machine interactions. Thus, this work provides a green, scalable, and straightforward approach for fabricating self-helical WG conductive fibers, which hold great promise for plant protein-derived wearable electronics in healthcare monitoring and human-machine interfacing applications.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF POWER SOURCES
·
2026
·
IF 8.4
Jiajia Zhu,Tingyu Zhao,Hexiang Lan,Longfei An,Luying He,Yuqi Jiang,Weiming Wang,Aiping Jin,Jun Xiong,Junjun Pen,Ming Li,Linghui Yu
1,1,2,2-Tetrafluoroethyl-2,2,3,3-tetrafluoropropylether (TTE) is widely adopted in lithium-ion batteries (LIBs) as a multifunctional electrolyte diluent. It effectively reduces electrolyte viscosity and salt concentration while preserving essential properties. Additionally, TTE enhances safety by acting as a flame retardant and improves low-temperature performance due to its low melting point. However, in spite of the extensive adoption, the use of highly TTE-rich electrolytes, which require minimal amounts of costly salts, has not been thoroughly explored. In this work, we systematically investigate carbonate electrolytes with high content of TTE, up to 95%, focusing on the effects of TTE on electrolyte flammability, conductivity, solvation structure, the electrode-electrolyte interface, and cell performance at different temperatures. The capacity fading mechanism is also discussed. The findings provide practical guidelines for utilizing TTE in LIBs.
✓ 已验证
产品关联
DOI
高影响因子
CHEMICAL ENGINEERING JOURNAL
·
2026
·
IF 12.5
Wenduo Zhang,Yan Lai,Lei Liu,Xiaorong Song,Meimei Zhang,Zhimeng Hao,Gaojing Yang,Lili Wang,Jianmin Ma
Sn(OTf) 2 is developed as a multifunctional additive for chloride-free Mg[B(HFIP) 4 ] 2 /DME electrolytes. • OTf − reconstructs Mg 2+ solvation sheath to lower desolvation barrier and accelerate ion transport. • Sn 2+ forms Sn on Mg anode and induces B(HFIP) 4 − into the Helmholtz layer to construct a robust bicontinuous SEI. • A thin, uniform and conductive CEI forms on Mo 6 S 8 cathodes, reducing charge-transfer resistance. • Mg Mg cells cycle stably for over 500 h and full cells deliver 68.11 mAh g −1 after 850 cycles. Rechargeable magnesium batteries are promising candidates for next-generation energy storage systems. However, their practical development is severely limited by electrolyte chemistry, especially chloride-free electrolytes with strong ion-solvent coordination and unstable electrode-electrolyte interfaces. Herein, a multifunctional additive, tin trifluoromethanesulfonate (Sn(OTf) 2 ), is introduced into a chloride-free magnesium tetrakis(hexafluoroisopropyloxy) borate (Mg[B-(OCH(CF 3 ) 2 ) 4 ] 2 )/1, 2-dimethoxyethane (Mg[B(HFIP) 4 ] 2 /DME) electrolyte to reconstruct anion-cation coordination and induce B(HFIP) 4 − anions into the Helmholtz layer. OTf − anions participate in the primary solvation sheath of Mg 2+ , lowering the desolvation barrier and accelerating interfacial Mg 2+ transport, while Sn 2+ electrostatically drives B(HFIP) 4 − enrichment at the Mg anode surface. The additive undergoes in situ redox reactions to generate metallic Sn, forming a robust boron-containing organic-inorganic bicontinuous solid electrolyte interphase. Simultaneously, Sn(OTf) 2 promotes a thin, uniform cathode electrolyte interphase on Mo 6 S 8 . Consequently, Mg Mg symmetric cells exhibit stable cycling for over 500 h at 0.5 mA cm −2 and 0.25 mAh cm −2 , while Mg-Mo 6 S 8 full cells deliver a reversible capacity of 68.11 mAh g −1 after 850 cycles at 0.5C. This work provides a novel strategy to unlock the potential of chloride-free electrolytes for practical rechargeable magnesium batteries. DME (1, 2-dimethoxyethane). Mg[B(HFIP) 4 ] 2 (magnesium tetrakis(hexafluoroisopropyloxy)borate). Sn(OTf) 2 (tin trifluoromethanesulfonate). SEI (solid electrolyte interphase). CEI (cathode electrolyte interphase). Download: Download high-res image (146KB) Download: Download full-size image
✓ 已验证
产品关联
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2026
·
IF 6
Qian Li,Zhenwei Yang,Yangyang Feng,Daxin Li,Zhaoxue Deng,Su Cheng
(SiC-BN)/BAS composite ceramics were prepared via reactive hot-press sintering at 1500 °C/10 MPa for 1 h. The effects of BN contents (0-14 wt.%) on the phase composition, density, microstructure, and mechanical properties of the composites were systematically investigated. The research showed that the incorporation of coal fly ash (CFA) and BN promoted a partial hexacelsian-to-celsian transformation. The BAS in composite ceramics primarily consists of hexacelsian and minor celsian. The celsian content reaches a maximum at 7 wt.% BN, corresponding to the peak residual compressive stress. The addition of BN leads to a gradual decrease in density and flexural strength, while fracture toughness first increases and then declines. At 7 wt.% BN, the ceramics achieve optimal comprehensive performance, with flexural strength and fracture toughness reaching 194.9 MPa and 3.74 MPa· m 1/2 , respectively. The enhancement is mainly attributed to the synergistic effects of weak interfaces introduced by BN (platelet pull-out, crack deflection, and crack bridging) and residual compressive stress induced by thermal expansion mismatch among the constituent phases.
✓ 已验证
产品关联
DOI
高影响因子
MINERALS ENGINEERING
·
2026
·
IF 6
Shengzong Lan,Liuyang Dong,Tianfu Zhang,Peilun Shen,Dianwen Liu,Zhengchang Shen
Ultrasonic treatment facilitates the flotation separation of calcite and apatite. • Ultrasonic treatment increases the specific surface area of calcite. • Ultrasonic treatment promotes the adsorption of NaOL on calcite surface. • Ultrasonic treatment enhances the exposure of high-energy crystal planes of calcite. • NaOL exhibits stronger adsorption energy on the high-energy crystal planes. Calcite is a widely distributed carbonate gangue mineral, which often coexists with calcium-bearing valuable minerals, making their separation difficult. This study aimed to clarify the enhancement mechanism of ultrasonic pretreatment on the flotation performance of calcite and its separation efficiency between calcite and apatite. Combined with density functional theory (DFT) calculations, multiple characterization techniques including specific surface area analysis, atomic force microscopy, microcalorimetry and X-ray photoelectron spectroscopy (XPS) were adopted to systematically explore the influences of ultrasonic pretreatment on the surface characteristics, crystal plane exposure of calcite, as well as the adsorption behavior of sodium oleate (NaOL) on calcite surfaces. The results indicate that at a NaOL concentration of 7.5 × 10⁻ 5 mol/L, ultrasonic pretreatment increases the calcite recovery from 59.46% to 92.54%, and improves the separation efficiency of apatite from calcite. Specifically, the cavitation and mechanical oscillation effects induced by ultrasound cause surface micro-etching of calcite, remarkably increasing the specific surface area and surface roughness while exposing more active sites. Meanwhile, ultrasound regulates the crystal plane exposure of calcite, significantly increasing the proportion of high-activity crystal planes. XPS and microcalorimetry results confirm that ultrasound facilitates the formation of a denser and more stable NaOL adsorption layer on the calcite. DFT calculations further verify that NaOL exhibits stronger adsorption energy on the high–activity crystal planes. Collectively, ultrasonic pretreatment improves calcite floatability through the synergistic effects of surface activation, crystal plane optimization, and adsorption enhancement. This study provides a novel method and theoretical support for the flotation separation of calcite from phosphate ore.
✓ 已验证
产品关联
DOI
高影响因子
POLYMER
·
2026
·
IF 5.1
Zhenyao Zhang,Xiaoming Qi,Liming Wang,Hongbo Dai,Jieyang Qiu,Qingqing Ni
Carbon fiber-reinforced epoxy composites are widely used in engineering applications owing to their excellent specific strength, modulus and cost performance. However, the brittleness and poor recyclability of the thermosetting epoxy matrix severely limit their sustainability. In this study, bisphenol A-type epoxy resin and bisphenol A were used as raw materials, and a 2-methylimidazole/tetrabutylammonium bromide catalytic system was employed to successfully prepare a high strength and toughness thermoplastic epoxy resin (TPE) via solution polymerization. The resulting TPE exhibited a weight-average molecular weight ( M w ) of 43078 g/mol and a polydispersity index of 1.29. In addition, the TPE exhibited outstanding mechanical and thermal performance, with high tensile strength of 76 MPa, toughness of 30.7 MJ m −3 and T d5% of 423 ° C. Carbon fiber-reinforced thermoplastic epoxy composites (CF/TPE) were fabricated via the prepreg compression molding process. The CF/TPE composites exhibited a tensile strength of 1022.7 MPa, flexural strength of 1042.5 MPa and interlaminar shear strength (ILSS) of 65.2 MPa. The TPE matrix can be efficiently dissolved in polar solvents, enabling the intact recovery of both carbon fibers and the TPE matrix. This approach provides a TPE to replace conventional thermosetting epoxy while also enabling an effective preparation-recycling route for sustainable use of carbon fiber composites.
✓ 已验证
产品关联
DOI
高影响因子
SENSORS AND ACTUATORS B-CHEMICAL
·
2026
·
IF 8.3
Fan Feng,Haicheng Gao,Yuan Xue,Qing Dong,Junfeng Zhai,Dan Li,Erkang Wang,Jin Wang
Exosomes, as extracellular vesicles, represent ideal biomarkers for liquid biopsy, enabling non-invasive, sensitive, and dynamic disease monitoring. Detection or profiling of exosomes are essential for advancing exosome-based cancer diagnostics or prognostic prediction. Here, we developed an enhanced electrochemiluminescence (ECL) biosensing platform that combines magnetic enrichment with catalytic hairpin assembly (CHA), an enzyme-free DNA amplification circuit triggered by the complementary sequences of CD63 aptamer (Apt), to achieve sensitive exosome detection. The enhanced ECL signal relies on a nanocomposite of a zirconium-based metal-organic framework (Zr-MOF) and water soluble gold nanoclusters (AuNCs), denoted as Zr-MOF/AuNCs. The platform exhibits a wide linear range (6.12 × 10² - 6.12 × 10⁷ particles/mL) and a low detection limit (187.4 particles/mL) for tumor-derived exosomes. Spike-recovery assays in complex serum matrices and high specificity confirm its robustness and clinical potential. By combining magnetic preconcentration, signal amplification via Zr-MOF and CHA, and Apt-mediated recognition, this work establishes a new paradigm for non-invasive cancer diagnostics.
✓ 已验证
产品关联
DOI
高影响因子
EUROPEAN POLYMER JOURNAL
·
2026
·
IF 6.8
Yali Yu,Aiqin Wang,Yongfeng Zhu,Bin Mu,Yan Liu,Xicun Wang
Coal gasification fine slag (CGFS) holds great potential for improving the performance of superabsorbent composites owing to its inherent mesoporous structure. However, the generation process of CGFS leads to surface activity passivation, making it difficult to achieve effective compatibilization with the polymer network. In this study, CGFS was activated via a mechanochemical approach through ball-milling using citric acid (CA) as a modifying agent. Subsequently, a novel superabsorbent composites, denoted as CS- g -PAM/CA-CGFS, was prepared via the graft copolymerization of chitosan (CS) and polyacrylamide (PAM). The mechanochemical modification increased the specific surface area of CGFS from 128.35 m 2 /g to 234.76 m 2 /g. Meanwhile, the activation process introduced abundant carboxyl groups (–COO − ) into CGFS and enhanced the interfacial compatibility between CGFS and the polymer network. When 10 wt% CA-CGFS was incorporated into the polymerization, the resulting superabsorbent composites exhibited water absorption capacities of 521.18 g/g in distilled water and 71.76 g/g in 0.9 wt% NaCl solution. Pot experiments further confirmed the excellent water retention capability of the superabsorbent composites in soil. When the material accounted for 0.5% of the soil mass, the fresh weight, dry weight, plant height and chlorophyll content of plants were 2.68, 4.09, 1.88 and 1.59 times those of the control, respectively. This research not only achieved high-value utilization of waste resources but also provides a promising route for developing high-performance superabsorbent composites for agricultural applications.
✓ 已验证
产品关联
DOI
高影响因子
ANALYTICAL BIOCHEMISTRY
·
2026
·
IF 3.1
Zunao Huang,Zeman Shao,Yanchun Wei,Li Quan,Hui Zhu,Qiuyang Zhang,Sen Liu,Zhongmei Yang
A novel D-shaped optical fiber sensor, functionalized with folate receptor protein for specific folic acid capture, is developed in this study. By employing a gold nanorod vacancy-filling amplification strategy, an exceptional sensitivity of 6.5 nm/ (ng mL -1 ) and an ultralow limit of detection of 0.012 ng/mL is achieved. The tunable nanoparticle occupancy time ensures stable detection sensitivity across varying analyte concentrations. This label-free sensing platform demonstrates robust specificity and excellent stability, offering significant potential for biomedical diagnostics and adaptable detection of diverse biomolecules. : Folic acid is an essential micronutrient for human growth, and either its excess or deficiency can provoke adverse physiological effects. Therefore, the development of a rapid and highly sensitive detection platform for folic acid is of substantial practical importance. In this study, a D-shaped optical fiber sensor is functionalized with a folate receptor protein to capture target analytes through specific ligand–receptor interactions. Vacant binding sites are subsequently occupied by functionalized gold nanorods for amplifying the fiber’s surface plasmon resonance (SPR) response. The incorporation of gold nanorods yields an enhanced SPR wavelength shift, leading to a significant improvement in detection sensitivity. The tunable nanoparticle occupancy time ensures the stability of detection sensitivity at various folic acid concentrations. Stability and specificity tests corroborated the sensor’s robustness and selectivity. The proposed device achieved a sensitivity of 6.5 nm/ (ng· mL -1 ) and a limit of detection of 0.012 ng/mL toward folic acid. This label-free, high-sensitivity approach offers considerable potential for biomedical applications. A highly flexible fiber-optic sensor with a broad detection range for acid sensing is developed by combining nanorod vacancy-filling with surface plasmon resonance (SPR) technology. Download: Download high-res image (154KB) Download: Download full-size image
✓ 已验证
产品关联
DOI
PubMed
高影响因子
INTERNATIONAL BIODETERIORATION & BIODEGRADATION
·
2026
·
IF 4.4
Fuyu Song,Jiaxi Liu,Qi Wu,Aiqin Diao,Yinhu Jiang,Xin Yan,Na Li,Jian He,Jiguo Qiu
An efficient Rhodococcus sp. YQ-4 strain degraded 98% of 2-ABT within 24 h. • A new intermediate metabolite (2-hydroxybenzothiazole) was identified. • A novel 2-ABT biotransformation pathway was proposed. • Biodegradation of 2-ABT was a detoxification process. 2-Aminobenzothiazole (2-ABT), a representative heterocyclic compound originating from tire wear particles, was widely detected in diverse environmental matrices. Due to its persistence and potential toxicity, the removal of 2-ABT from contaminated environments has become an increasing environmental concern. However, studies on the efficient biodegradation of 2-ABT by pure cultures remain limited. In this study, the abundance of Rhodococcus increased significantly following enrichment and acclimation. Subsequently, a 2-ABT-degrading pure culture, designated Rhodococcus sp. YQ-4, was isolated. Under the optimal conditions of pH 7.0, 1% NaCl, and 30 °C, strain YQ-4 achieved a removal rate of 98% for 50 μM 2-ABT within 24 h. A key metabolic intermediate, 2-hydroxybenzothiazole (2-OBT), was identified by liquid chromatography-time-of-flight mass spectrometry (LC-TOF-MS). Based on these results, a possible initial biotransformation pathway involving deamination and hydroxylation at the C2 position of the thiazole ring was proposed. Furthermore, toxicity bioassays involving the green alga Chlamydomonas ellipsoidea and mung bean ( Vigna radiata ) demonstrated that the biodegradation of 2-ABT by strain YQ-4 significantly alleviated its phytotoxicity, thereby restoring the growth and physiological vigor of the test species. Collectively, this study provided a novel bacterial resource for the bioremediation of 2-ABT-contaminated environments and offered new insights into the catabolic pathway associated with emerging pollutants.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY
·
2026
·Vol. 46
·期 16
·118645
·
IF 6.3
Yuzhe Xie,Jie Zhang,Yuting Liu,Xing Luo,Zixiang Pei,Baohua Cao,Konrad Świerczek,Yang Zhang,Wanbing Guan
To mitigate interconnect corrosion in seawater-fed solid oxide electrolysis cells (SOECs), Mn 1.5 Co 1.5 O 4 spinel coatings were deposited on Fe-22Cr stainless steel. At 750 °C, the coated interconnects exhibited an area-specific resistance (ASR) of 31.8 mΩ cm 2 after 4835 h of oxidation in air, with a parabolic rate constant of 3.0 × 10 −5 mg 2 cm −4 h −1 . Following exposure to seawater vapor for 500 h, the ASR reached 3.36 mΩ cm 2 , with a predicted value of 9.80 mΩ cm 2 at 5000 h. These findings underscore the coating’s improved oxidation resistance under dual-atmosphere conditions. Furthermore, a three-cells stack demonstrated high stability with a low degradation rate of 1.04 × 10 −5 h −1 at 100 mA cm −2 for 100 h. Post-test analysis confirmed a crack-free structure with negligible additional resistance, indicating that the spinel coating satisfies the engineering requirements for durable, direct seawater electrolysis and provides a scalable pathway for green hydrogen production.
✓ 已验证
产品关联
DOI
高影响因子