Collagen and Leather
·
2026
·Vol. 8
·期 1
·25
·
IF 10.1
Jiang Qingmiao,Zhou Yuxin,Liu Minghua,Lv Yuancai,Guo Hong,Liu Yifan,Ye Xiaoxia,Shi Yongqian
With the depletion of petroleum resources, biomass has been widely applied as an alternative to petroleum-based feedstocks. In this work, a lightweight tannin-lignin-phenolic carbon foam (TLCF 5−ME ) with excellent smoke suppression was developed. The foam precursor was prepared by substituting 30 wt% of phenol with modified lignin, and tannin was used as a framework filler to reinforce the samples. The effects of lignin, tannin type, including myrica extract (ME), wattle extract (WE), and tannic acid (TA), and addition amount of tannin on the mechanical behavior and smoke suppression of carbon foam were determined, and the mechanism was illustrated. Surprisingly, it was found that the total smoke release of TLCF 5−ME was only 0.39 m 2 /m 2 , which was 97.62% lower than that of pure phenolic carbon foam (CF), and the compressive strength of TLCF 5−ME was 0.32 MPa, which was 33.33% higher than that of CF. In summary, adding modified lignin and ME not only reduced the use of phenol, but also increased the number of aromatic rings and improved the graphitization degree of carbon foam, thereby promoting the formation of compact char layers under combustion, and further effectively inhibiting the smoke production of samples. Graphical
✓ 已验证
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE
·
2026
·
IF 4.4
Yan Zhuoxi,Zhang Jixiang,Zhang Han,Zhou Keyu,Zhang Jingjing
Polyvinyl alcohol (PVA) hydrogels are promising materials for soft robotics, biomimetic devices and wearable sensors, yet their practical applications are often hindered by low tensile strength and insufficient surface friction. Herein, a high-friction and tough PVA/polyisobutylene (PIB) hydrogel was successfully fabricated via a one-pot method combined with a solvent exchange strategy. Fourier transform infrared spectroscopy, X-ray diffraction and differential scanning calorimetry were employed to characterize the chemical interactions and crystalline behaviors of the hydrogels, while the water content, swelling ratio, microcosmic observation, tensile strength and tribological performance were tested to investigate the combination properties of hydrogels. The results revealed that glycerol was optimal for enhancing mechanical properties by promoting PVA crystallization and forming a dense network. The incorporation of PIB serving as a filler significantly improved the friction coefficient while maintaining adequate tensile strength. The PVA/PIB hydrogel with a PVA/PIB mass ratio of 17:3 exhibited the balanced performance, with a tensile strength of 1.5 MPa, an elongation at break of 545%, a high friction coefficient of 0.83 (which was higher than that of other hydrogels, up to 0.1191) and a low specific wear rate of 7.27 10 –4 mm 3 /Nm. Mechanistic studies indicated that the increase of friction resulted from the synergistic effects of PIB film formation, obstruction of water spillage under compression and the optimal material strength. Graphical abstract
✓ 已验证
DOI
高影响因子
JOURNAL OF RADIOANALYTICAL AND NUCLEAR CHEMISTRY
·
2026
·
IF 1.7
Liu Xiaotong,Li Hui,Xu Chengjin,Peng Xiujing,Sun Guoxin,Cui Yu,Lu Ping
Efficient separation of nuclear-grade zirconium (Zr) and hafnium (Hf) remains a significant challenge in the nuclear industry. In this study, a novel extractant, di(p-tert-octylphenyl) phosphate (DTOPPA), was designed and synthesized. DTOPPA demonstrated preferential extraction of Hf over Zr in sulfuric acid media, surpassing the performance of conventional extractants such as D2EHPA and PC88A. Under optimized conditions, Hf(IV) extraction achieved 90.7% with a separation factor SF (Hf/Zr) of 13.4. Density functional theory (DFT) calculations and acid–base titration indicated enhanced dissociation of DTOPPA, attributed to the electron-withdrawing phenoxy group, which facilitates cation exchange. Slope analysis, saturation capacity measurements, and Fourier-transform infrared spectroscopy (FTIR) identified the extracted species as Zr(Hf)OA 2 ·2DTOPPA, involving cation exchange and P=O coordination. Selective stripping of Zr was accomplished using dilute sulfuric acid, while oxalic acid efficiently stripped Hf. A two-stage countercurrent extraction process yielded nuclear-grade Zr with stable organic phase recycling. This novel extractant provides an environmentally friendly and efficient method for Zr/Hf separation with significant potential for industrial application.
✓ 已验证
DOI
高影响因子
JOURNAL OF SOLUTION CHEMISTRY
·
2026
·
IF 1.3
Chen Yuhuan,Chen Jing,Chen Chunhong,Yang Fang
In this work, n EB-PEI 1800 ( n = 0.22, 0.29, 0.35), a property tunable polymer for CO 2 capture, is reported by partially modifying poly (ethylene imine) (PEI 1800 ) with 1,2-epoxybutane (EB). The density and viscosity of CO 2 -free and loaded aqueous n EB-PEI 1800 solution are measured at the temperatures of (293.15 to 333.15) K and 0.1 MPa. The aqueous solutions with various weight fractions of w = (5, 10, 15, 20 and 30%) are investigated. According to the experimental data, thermal expansion coefficient ( α p ), viscosity activation energy ( E η ) and CO 2 diffusion coefficient ( D CO2 ), are calculated. The influence of temperature, n EB-PEI concentration, CO 2 loading and modification degree are discussed from the viewpoints of molecular interaction and steric effect. The results reveal that low temperature, high n EB-PEI concentration and high CO 2 loading lead to high density and viscosity. Modification degrees have a great impact on the physical properties of n EB-PEI 1800 + H 2 O systems and can reduce the density and viscosity. The density and viscosity values exhibit the decreasing sequence of ρ PEI + H2O > ρ 0.29EB-PEI + H2O > ρ 0.35EB-PEI + H2O ≈ ρ 0.22EB-PEI + H2O and η PEI + H2O > η 0.22EB-PEI + H2O > η 0.35EB-PEI + H2O > η 0.29EB-PEI + H2O , respectively. All the results are attributed to the combined effects of hydrogen bonding, dispersion force and steric structure.
✓ 已验证
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2026
·Vol. 37
·期 6
·451
·
IF 3.2
Li Xiaoyuan,Zhu Guosong,Pan Wenqian,Zhou Wei,Lu Yuhai,Yue Jing,Xiao Peng,Luo Heng,Li Yang
Conventional microwave-absorbing materials struggle to meet modern demands for ‘thinness, light weight, wide bandwidth, and strong absorption’ in complex electromagnetic environments. Furthermore, emerging applications require new functionalities, specifically low-frequency absorption and multi-band response. To address these challenges, this work designs and constructs a multi-mechanism synergistic absorbing system based on a rare earth-transition metal Y-Co (Y 2 Co 17 ) alloy. The system is fabricated via heterogeneous deposition and thermal treatment to obtain ZnO@YCo composites. The results offer significant implications for the development of low-frequency and multi-band electromagnetic wave-absorbing materials. The main research contents and findings are as follows: A heterogeneous deposition method was employed to introduce needle-like ZnO heterostructures on the surface of YCo particles, followed by thermal treatment to optimize the absorption performance of ZnO@YCo composites. By adjusting the heat treatment temperature, the ZnO morphology was tuned. At 300 °C, the ZnO coating exhibited a well-defined structure with minimal agglomeration. The material demonstrated enhanced low-frequency absorption while retaining good performance in the high-frequency range (14–18 GHz). At a thickness of 6 mm, the minimum RL of ZnO@YCo reached − 5.86 dB at 5.6 GHz, outperforming the pristine YCo powders (RL > − 2.5 dB), thus exhibiting promising low-frequency absorption capabilities.
✓ 已验证
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2026
·Vol. 37
·期 18
·1440
·
IF 3.2
Wahab Fazal,Ren Zhenyi,Wang Fengjiang
As power semiconductors evolve toward higher frequencies and higher power densities, conventional soldering technologies—characterized by low melting points, poor thermal conductivity, and inadequate reliability—can no longer meet the packaging requirements of third-generation semiconductors such as SiC and GaN. In response, this study adopts sintered silver technology as a promising alternative. Three silver paste formulations were prepared using ether-based solvents with distinct evaporation characteristics, and the effect of solvent volatility on the low-temperature pressureless sintering performance of submicron silver particles was systematically evaluated. Variations in volatilization temperature and thermal energy requirements among the three solvents led to distinct microstructural morphologies and densification behaviors, revealing a correlation between electrical resistivity and void evolution. Notably, Ether I exhibits an exothermic peak during volatilization, along with low latent heat of evaporation and an appropriate volatilization temperature. The sintered joint prepared with this solvent achieved a shear strength of 79.61 MPa, a thermal conductivity of 221.17 W m −1 K −1 , and a volume resistivity of 4.86 × 10 −6 Ω cm at a sintering temperature of 220 °C. These results demonstrate the considerable potential of pressureless silver sintering technology for interconnections in power electronics packaging applications.
✓ 已验证
DOI
高影响因子
POLYMER BULLETIN
·
2026
·Vol. 83
·期 9
·483
·
IF 4.2
Liu Lang,Li Zhiqiang,Ge Susu,Zuo Limei,Wei Yanyan
In this paper, polyvinyl alcohol-borax hydrogel was used as the base material. The incorporation of tannic acid-modified cellulose nanocrystals (TA@CNC) combined with a freeze-thaw process endowed the hydrogel with self-adhesive properties and improved mechanical performance. Meanwhile, the addition of MXene and Al³⁺, coupled with a shortened freeze-thaw duration, further enhanced the hydrogel’s stretchability and strain-sensing capabilities. The prepared hydrogel can macroscopically repair generated damages due to the cleavage and formation of borate ester bonds. When the content of TA@CNC increased from 0wt% to 0.4wt%, the tensile strength of the hydrogel increased from 13.5 kPa to 33.3 kPa, and the elongation at break rose from 1350% to over 2000%. Its adhesion to aluminum materials reached a maximum of 16.2 kPa, and the self-healing efficiency within 60 s achieved 99.4%. MXene, owing to the good dispersibility of its specific functional groups in water, imparts excellent electrical conductivity to the hydrogel. With the introduction of Al³⁺, the 24-hour self-healing efficiency of the hydrogel increased from 73.9% to 87.3%, and the recovery rate of cyclic tensile curves under 200% strain reached 91.1%, indicating favorable resilience and anti-fatigue performance. These properties enable the conductive hydrogel to not only convert large strains into regular electrical signal curves but also detect microstrains.
✓ 已验证
DOI
高影响因子
APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING
·
2026
·Vol. 132
·期 8
·678
·
IF 3
Li Jianhui,Zhuang Shaoling
In this study, high-quality nanoselenium (quantitatively defined as monodisperse ~ 35 nm particles, high crystallinity, 99.6% purity, and good colloidal/thermal stability) was successfully fabricated via a facile heterogeneous titration approach, using selenium powder as the precursor, an ethylenediamine–ethanethiol binary mixture as the reaction medium, and deionized water (DI water) as the titrant. The product was systematically characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), zeta potential analysis, dynamic light scattering, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and X-ray photoelectron spectroscopy (XPS) to reveal its morphology, crystal structure, surface chemistry, and thermal stability. The results demonstrated that the as-prepared nanoselenium featured an average particle size of 35 nm (ascertained by TEM and XRD) and an average yield of 2.79 ± 0.01 g (99.6%) based on triplicate experiments, exhibiting excellent performance with ultra-small particle size and high synthetic efficiency. Further investigation revealed that the synergistic effect between ethylenediamine (acting as both reaction medium and stabilizer) and ethanethiol (serving as a capping agent) efficiently regulated the nucleation and growth of selenium nanoparticles, which is crucial for the superior product performance. This work presents a straightforward yet highly efficient heterogeneous titration strategy for producing high-quality nanoselenium, laying a solid foundation for its future application-oriented research.
✓ 已验证
产品关联
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE
·
2026
·Vol. 61
·期 13
·8556-8568
·
IF 4.4
Jia Jiru,Tang Yusheng,Jin Jing,Wang Xiaofei,Zhao Jin,Peng Jun,Chen Baishun
Electroless deposition (ELD) via spontaneous redox reactions between metal precursors and carbon substrates provides a sustainable and surfactant-free approach to supported metal nanoparticles (NPs). However, it is often limited by the weak reducing ability and cost of conventional carbons. Herein, we report a biomass-derived carbon (BC) prepared from microcrystalline cellulose (MC) as a low-cost carbon matrix that acts as both the reducing agent and the stabilizer for ELD of noble metals. Nitrogen (N)-doped biomass carbon (NBC) further improves deposition control, enabling tunable Pd loading, particle size, and dispersion with nitrogen content. Pd/NBC 5 shows an about threefold higher activity for 4-nitrophenol (4-NP) reduction than commercial Pd/C under identical conditions, mainly due to uniform Pd dispersion and nitrogen-enabled interfacial effects. Using the same procedure, NBC 5 also enables ELD of Au, Pt, and Ru with good dispersion, demonstrating the generality of this nitrogen-tunable biomass carbon. This work provides insights into how nitrogen tuning in biomass carbons regulates ELD behavior and offers a mild, aqueous, reductant-free strategy to construct carbon-supported noble metal nanocatalysts for chemical and environmental catalysis. Graphical abstract
✓ 已验证
DOI
高影响因子
CELLULOSE
·
2026
·
IF 4.6
Chen Jinghuan,Liu Junjun,Yang Kaiji,Peng Xuanhua,Deng Wangfang,Tarasov Dmitry,Gustafsson Jan,Hu Liqiu,Xu Jiayun,Zhang Hao,Sun Shaofei,Tian Chao,Sun Bo,Xu Chunlin
Microfibrillated cellulose (MFC) has attracted increasing attention as a sustainable reinforcement for polymer composites. However, when incorporated into hydrophobic thermoplastics such as acrylonitrile–butadiene–styrene (ABS), MFC often improves tensile strength but significantly reduces elongation at break. To address this challenge, we designed a surface modification strategy for MFC. Leaf bleached kraft pulp (LBKP) was first carboxyethylated and mechanically fibrillated to produce carboxyethylated MFC (C-MFC), which was subsequently amidated with octadecylamine (ODA) to obtain hydrophobized octadecylamine-modified carboxyethyl MFC (OC-MFC). Composite films of OC-MFC/ABS were fabricated by solution casting followed by hot pressing. The structures and properties of MFC, C-MFC, OC-MFC, and OC-MFC/ABS composites were systematically characterized using laser particle size analysis, FTIR, dynamic water contact angle, tensile testing, thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). The results demonstrated that ODA modification effectively increased the hydrophobicity of MFC, leading to improved dispersion and interfacial compatibility with the ABS matrix. Mechanical testing revealed that the incorporation of 0.5–1 wt% OC-MFC into ABS composite films preserved the tensile strength, while significantly enhancing. Morphological observations further supported the toughening effect of OC-MFC. These findings highlight a practical strategy for toughening ABS through the incorporation of surface-modified MFC, providing insights into the design of high-performance bio-based thermoplastic composites. Graphical
✓ 已验证
DOI
高影响因子
ANALYTICAL AND BIOANALYTICAL CHEMISTRY
·
2026
·
IF 4.1
Zheng Yongfang,Huang Shuijing,Zhu Xinyu,Chen Yuyuan,Tian Shuli,Pang Yuxuan,Zhuang Chaojie,Zhu Hu
Nanozymes (primarily peroxidase mimics) coupled with glucose oxidase (GOx) have emerged as an important approach for glucose sensing. However, the widespread application of this strategy is hampered by a critical pH mismatch, as most such nanozymes require an acidic environment for high activity, preventing one-step detection at physiological pH. Here, we report a cascade colorimetric sensing platform based on our previously reported haloperoxidase (HPO) mimic HH-Cu, which exhibits high HPO-like activity exclusively under neutral and alkaline conditions, enabling one-step glucose detection at physiological pH. In this system, GOx catalyzes the oxidation of glucose to generate H 2 O 2 , which is utilized by HH-Cu along with externally added Br − to convert phenol red into bromophenol blue (λmax = 590 nm) through its HPO-like activity, resulting in a visible color change from orange to blue. Spectrophotometric analysis yielded a linear detection range of 1–600 μM and a detection limit of 0.99 μM for glucose, with recovery rates of 90.8%–106.6% and relative standard deviations (RSD) below 7% in urine samples. A smartphone-based analysis platform was also developed and showed performance comparable to the spectrophotometric method, with a linear range of 2.5–600 μM, a detection limit of 2.20 μM, and recovery rates of 105.5% in biological samples. Both platforms were also successfully applied to the sensitive detection of H 2 O 2 at physiological pH. This work not only overcomes the key limitation of pH mismatch in conventional enzyme/nanozyme-based colorimetric glucose detection but also broadens the application horizon of HPO mimics in biosensing. Graphical
✓ 已验证
产品关联
DOI
高影响因子
MICROCHIMICA ACTA
·
2026
·Vol. 193
·期 7
·495
·
IF 5.4
Shi Jian,Shan Xiaomu,Wang Hongren,Xu Yuanze,Zhang Zezheng,Fan Xiuwei,Du Xuejian,Jiang Shouzhen
A high-performance optical fiber surface plasmon resonance (SPR) biosensor for the determination of dopamine (DP) is reported based on gold nanocone arrays combined with gold nanoparticles (AuNPs). The sensor was fabricated via thermal nanoimprinting, gold sputtering, and single-stranded DNA-assisted AuNPs immobilization to form gap hotspots. Finite element simulation and experimental results verified strong electromagnetic field enhancement via extraordinary optical transmission and SPR-LSPR coupling. The sensor achieved a detection limit of 2.7 × 10 -14 M for DA, with sensitivity and FOM improved by 37.4% and 54.2% relative to conventional gold film structures. It showed excellent selectivity and stability in serum, cerebrospinal fluid (CSF), and whole blood. This robust, scalable design provides a promising label-free platform for ultrasensitive DA detection in clinical point-of-care applications. Graphical abstract
✓ 已验证
DOI
PubMed
高影响因子