JOURNAL OF MATERIALS SCIENCE
·
2026
·Vol. 61
·期 27
·19586-19601
·
IF 4.4
Wei Chenzhuo,Niu Yanting,Zhou Yuqing,Ji Yujie,Peng Jinda,Gu Yuhao,Zhang Xing,Han Qian,Guo Yang,Lei Jiuli,Zhu Nanfeng,Cui Juqing
The development of high-performance wearable electronic demands flexible strain sensors with high sensitivity and robust durability. Herein, we present a high-sensitivity flexible strain sensor based on a polydimethylsiloxane/carbon nanotube (PDMS/CNT) nanocomposite incorporated with electrospun cellulose acetate nanofibers (CANF). The unique integration of CANFs endows the PDMS/CANF/CNT nanocomposite with enhanced mechanical strength and tear resistance while maintaining excellent stretchability. The results show that the tensile strength and toughness of the PDMS/CANF/CNT composites increased from 2.80 to 4.20 MPa and from 1900.00 to 3900.00 kJ/m 3 , respectively. For composites with pre-cut cracks, the tensile strength increased from 0.37 to 1.00 MPa, and the toughness increased from 46.55 to 113.90 kJ/m 3 . SEM observations reveal that CANFs play a critical role in promoting CNT dispersion and preventing agglomeration in the PDMS composites. The resulting flexible strain sensor demonstrates a high gauge factor and good stability over more than 100 stretching-releasing cycles. Furthermore, it was successfully applied in real-time monitoring of various human joint movements, including those of the elbow, knee, and neck. This work highlights the effectiveness of electrospun nanofiber regulation in fabricating advanced PDMS/CNT nanocomposites for next-generation flexible electronic devices. Graphical abstract
✓ 已验证
DOI
高影响因子
JOURNAL OF SOLUTION CHEMISTRY
·
2026
·
IF 1.3
Xu Saiyuan,Guo Yujun,Wu Yibin,Chen Bin,Xu Yingjie
This study aims to develop and characterize a novel mixed system composed of sodium phenoxide (NaOPh) and a deep eutectic solvent (DES) formed from 1-ethyl-3-methylimidazole chloride ([Emim]Cl) and ethylene glycol (EG), in order to address the phase separation issue commonly encountered in aqueous phenoxide solutions during CO₂ absorption—caused by the generation of phenol. The physicochemical properties, CO 2 absorption performance and absorption mechanism of the NaOPh/DES mixed system were investigated. The results indicate that the density, viscosity, and CO 2 absorption capacity of the studied NaOPh/DES mixed systems increase with NaOPh content. The NaOPh1.0/DES system exhibits the best absorption performance of these systems, with a CO 2 absorption capacity of 2.10 mol‧kg −1 at 313.15 K and 0.1 MPa. DFT calculations reveal that the Na + from NaOPh, the O–H group from EG, and the Cl − from [Emim] Cl can form a stable four-membered ring. This weakens the electrostatic interaction between Na + and [PhO] − , promoting the dissociation of the NaOPh and facilitating the chemical reaction between the “free” [PhO]⁻ and CO 2 to form carbonates. This mechanism is confirmed by FT-IR and 13 C NMR spectra. Using [Emim]Cl–EG DES as a solvent to dissolve NaOPh leverages the reactivity of [PhO] − with CO 2 for efficient absorption, while effectively avoiding phase separation. This expands the application of phenoxide-based systems in CO₂ capture.
✓ 已验证
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE
·
2026
·Vol. 61
·期 31
·22909-22923
·
IF 4.4
Kang Chenchen,Wang Xinyi,Zhang Fan,Deng Jiahao,Xiang Ziqi,Pang Lingyan,Liu Hui
Lithium–sulfur (Li–S) batteries are regarded as one of the most promising next-generation energy storage technologies owing to their ultrahigh theoretical specific capacity and energy density. Nevertheless, their practical application is still hampered by severe polysulfide shuttling, poor electrode conductivity, and large volume variation during cycling. Herein, medical-grade cotton wool was employed as a sustainable carbon precursor to construct a porous carbon framework, followed by solvothermal and thermal treatment to obtain orthorhombic Nb 2 O 5 /PC (T-Nb 2 O 5 /PC). Furthermore, thiourea was introduced as a dopant source to achieve nitrogen and sulfur co-doping, generating nitrogen/sulfur co-doped T-Nb 2 O 5 -modified biomass-derived porous carbon (NS-T-Nb 2 O 5 /PC) with synergistic catalytic activity and enlarged surface area. Comprehensive structural analyses reveal that N/S co-doping not only induces abundant lattice defects and active sites but also optimizes the electronic configuration and ion-transport channels while preserving the crystal integrity. Benefiting from these features, the NS-T-Nb 2 O 5 -1/PC/S electrode delivers a high initial discharge capacity of 1263.5 mAh g −1 at 0.1 C and maintains 685.5 mAh g −1 after 200 cycles, together with outstanding reversibility and rapid kinetics in the 0.1–1 C range. This work offers an effective strategy to regulate the electronic structure and interfacial chemistry of Nb 2 O 5 -PC host via in situ heteroatom doping, thereby enabling suppressed shuttle effect and enhanced Li–S battery performance.
✓ 已验证
DOI
高影响因子
JOURNAL OF MATERIALS SCIENCE
·
2026
·Vol. 61
·期 31
·22999-23012
·
IF 4.4
Wang Tielin,Ji Jiahao,Lin Tao,Lian Fang,Meng Nan,Shao Huiping
The self-standing electrodes attract widespread attention because of the rapid development of flexible micro energy storage devices in recent years. In this study, the self-standing lithium iron phosphate electrodes containing lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) are prepared by 3D printing. The effects of different LiTFSI contents on electrode are investigated, and the electrochemical performance of the self-standing electrodes is analyzed and discussed. The results show that as the printing needle diameter is 0.16 ± 0.02 mm and an air pressure is 0.65 MPa, the printing slurry of self-standing electrodes exhibits an apparent viscosity of 4.77 Pa s at shear rate of 198.1 s −1 , which is suitable for 3D gel printing. Electrochemical tests show that the self-standing electrodes maintain a stable voltage plateau and rate capability during charge–discharge processes after undergoing 500 cycles for 90° bending. After 300 charge–discharge cycles at 0.5C, the specific capacities of the self-standing electrode and the electrode after bending are 102 mAh g −1 and 99 mAh g −1 , with capacity retentions of 90.9% and 91.6%, respectively. The prepared self-standing electrodes exhibit high electrochemical stability cycling performance, which provides a reference for 3D printing of self-standing electrodes.
✓ 已验证
DOI
高影响因子
CELLULAR AND MOLECULAR LIFE SCIENCES
·
2026
·
IF 6.5
Zeming Lei,Liangzi Yin,Bin Zhang,Ziyuan Wang,Yansheng Wang,Lunhao Bai
Wear debris-induced periprosthetic osteolysis (PPO) is a major complication following total joint arthroplasty, leading to implant failure. Macrophage inflammatory response and osteoclastogenesis play important roles in bone destruction and resorption in PPO. KDM5C (lysine-specific demethylase 5 C), a H3K4 demethylase, functions as a transcriptional repressor in various biological processes, including immune response, energy metabolism, and neurodevelopment. However, its role in PPO pathogenesis remains unclear. In this study, we observed elevated KDM5C expression in macrophages exposed to Titanium (Ti) particles in vitro. Genetic inhibition of KDM5C attenuated Ti particle-induced upregulation of pro-inflammatory factors and reduced the release of inflammatory cytokines. Moreover, KDM5C knockdown suppressed osteoclast differentiation, as evidenced by the decrease in osteoclast number and osteoclast-specific marker expression. Mechanistically, KDM5C was found to repress NFE2L2 transcription by decreasing H3K4 trimethylation (H3K4me3) at its promoter. Inhibition of NFE2L2 abolished the protective effects of KDM5C knockdown on macrophage inflammation and osteoclast differentiation. The calvarial osteolytic model in vivo also demonstrated that silencing KDM5C alleviated Ti particle-induced bone destruction, inflammation, and osteoclastogenesis. Collectively, these findings suggest that KDM5C promotes macrophage inflammatory response and osteoclastogenesis by repressing NFE2L2 transcription through decreasing H3K4me3 levels. It may offer a novel insight into the potential therapeutic target for wear particle-induced osteolysis.
✓ 已验证
DOI
PubMed
高影响因子
Science China-Materials
·
2025
·Vol. 69
·期 1
·215-227
·
IF 7.4
Chen Guangyuan,Tang Tingting,Li Yubao,Lin Chenyang,Zhou Shijian,Kong Yan
Metal sulfides like CdS hold promise for solar-driven H 2 O 2 productions but suffer from rapid charge recombination and severe photocorrosion. This study introduces a dual-functional strategy synergizing sulfur vacancy (S v ) engineering and polydopamine (PDA) coating to overcome these limitations. S v -CdS nanorods were hydrothermally synthesized with tunable vacancy concentrations, followed by in-situ PDA deposition to construct a direct Z-scheme heterojunction. X-ray photoelectron spectroscopy (XPS) and density functional theory (DFT) calculations reveal that the introduction of S vacancies reduces the work function of CdS, facilitating energy level alignment with PDA and enabling efficient electron transfer from CdS to PDA. By tuning the concentration of S vacancies, the charge transfer efficiency can be maximized. As a result, the photocatalytic H 2 O 2 production rate reaches 2539.5 µmol g −1 h −1 under visible light, and further increases to 4395.5 µmol g −1 h −1 after PDA encapsulation —15.6 times higher than that of pristine CdS. Concurrently, PDA enhances O 2 adsorption and protects S v -CdS from photocorrosion. S v -CdS@PDA exhibited superior photostability compared to S v -CdS after three consecutive photocatalytic cycles. Mechanistic studies suggest that the Z-scheme heterojunction effectively separates electron-hole pairs: electrons in the conduction band of CdS reduce O 2 to ·O 2 − , which is subsequently converted to H 2 O 2 , while holes in the valence band of S v -CdS oxidize water to replenish O 2 . This work provides fundamental insights into engineering charge transfer and stability in sulfide-based photocatalysts.
✓ 已验证
DOI
高影响因子
RESEARCH ON CHEMICAL INTERMEDIATES
·
2026
·
IF 3.3
Ai Hengyu,Meng Fanqi,Wang Shanshan,Taran Oxana P.,Sun Fubao,Yan Hong
Mn 0.5 Cd 0.5 S (MCS) is widely used in photocatalytic hydrogen production via water splitting. However, its inherent drawbacks, including low separation efficiency of photogenerated electron–hole pairs, poor stability, and severe photocorrosion, limit hydrogen production efficiency. In this study, carbon quantum dots (CQDs) were synthesized using alkaline lignin as the carbon source and were loaded onto the surface of MCS via ultrasonic-assisted treatment to construct CQDs/MCS composite photocatalyst. Characterization results revealed that the introduction of CQDs did not alter the crystal structure of MCS but effectively broadened its light absorption range, leading to a red shift of the absorption edge and a narrowed band gap, as well as reduced charge transfer resistance and hydrogen evolution overpotential. The CQDs/MCS composite photocatalyst with the addition of 15 mL CQDs solution exhibited the optimal photocatalytic performance, with a hydrogen evolution rate of 13.11 mmol g −1 h −1 , which was 1.33 times higher than that of pure MCS. Moreover, the composite showed excellent recyclability. The enhanced hydrogen evolution performance of CQDs/MCS can be attributed to the fact that CQDs can capture photogenerated electrons and accelerate the separation of electron–hole pairs. In conjunction with the hole consumption by sacrificial agents, the CQDs/MCS composite achieved significantly enhanced photocatalytic hydrogen evolution performance.
✓ 已验证
产品关联
DOI
高影响因子
FIBERS AND POLYMERS
·
2026
·
IF 3.1
Han Jiawei,Wang Yi,Deng Kehui
Electrospun protein–polysaccharide nanofibers are promising biocompatible substrates for skin-contact materials, yet controlling their morphology and hydration behavior in ternary systems remains challenging. In this work, the modification of a cod collagen peptide/poly(ethylene oxide) (CCP/PEO) system with sodium alginate (SA) was investigated as a model polyelectrolyte interaction. A three-factor Box–Behnken design was applied to optimize the spinning-solution preparation for the liquid absorption capacity (LAC), yielding an optimum at a 12.5 h reaction time, 30 °C, and a 30:1 CCP/SA mass ratio. SEM, FTIR, and XRD analyses indicated that electrostatic association and hydrogen bonding between the protonated amino groups of CCP and carboxylate groups of SA facilitated the formation of uniform nanofibers (458 ± 114 nm) with reduced crystallinity. These interactions significantly enhanced the mechanical performance ( p < 0.01), with a 13.1% increase in tensile strength and a 27.3% increase in elongation at break. Compared to unmodified controls, the SA-modified composite mats exhibited a ~ 27% higher LAC (1063.9%) and improved water retention after simulated skin contact, despite a moderate reduction in permeability. A three-stage hydration mechanism—comprising capillary substrate uptake, osmotic swelling within the proposed polyelectrolyte network, and nanofiber dissolution—is proposed to explain the enhanced hydration capacity. This study provides a quantitative process map for the design of high-performance dry-state carriers for functional facial masks.
✓ 已验证
产品关联
DOI
高影响因子
CATALYSIS SURVEYS FROM ASIA
·
2026
·
IF 2.5
Shan Yulin,Li Junjie,Li Chao,Bai Zixuan,Li Binglin,Liu Ziwei
Conventional syntheses of tocopheryl acetate rely on strong Brønsted/Lewis acids and energy-intensive conditions. Here we report a visible-light photocatalytic route using graphitic carbon nitride (g-C 3 N 4 ) engineered by precursor control, P/S co-doping, metal loading (Cu, V, Zn, Ni), and nanosheet formation. Structural characterization by SEM and TEM revealed that P/S co-doping and exfoliation produced highly corrugated nanosheets with increased porosity, abundant edge sites, and reduced interlayer stacking. XRD analysis confirmed the preservation of the g-C 3 N 4 framework with slight distortion upon doping, while HRTEM showed lattice disorder and defect formation that are beneficial for charge trapping and transfer. In ethanol/H 2 O 2 under a 40 W lamp, P/S@g-C 3 N 4 affords a 76.26% yield with 99.80% selectivity; no formation occurs in the dark. Screening identifies 5 mg mL −1 substrate, 4 mg catalyst, and 45 °C as optimal, while yields decline above 55 °C. The catalyst is reusable for 20 cycles with slight loss from handling. DRS results showed that the absorption capacity of P/S@g-C 3 N 4 to visible light was significantly higher than that of g-C 3 N 4 . And compared with g-C 3 N 4 , the E g value of P/S@g-C 3 N 4 is significantly narrowed form 2.71 eV to 2.42 eV. Mechanistic analysis indicates P/S sites and heterointerfaces enhance H 2 O 2 activation, oxidize ethanol to acetaldehyde, and channel coupling with a phenoxyl intermediate from tocopherol. This acid-free strategy offers a scalable route to tocopheryl acetate.
✓ 已验证
DOI
高影响因子
Nano-Micro Letters
·
2026
·Vol. 18
·期 1
·409
·
IF 38.5
Xu Yan,Zhang Xuefei,Lou Size,Tang Zhe,Xie Dongmei,Zhang Chuanrui,Chen Mengran,Liu Heng,Sun Chuan,Ou Yixiang,Zong Peng-an
A pyramid-interface-structured Bi 2 Se 3 layer was electrochemically constructed on flexible carbon paper, exhibiting excellent hydrophobicity with a contact angle of 143.7°.
Dual-mode decoupling of temperature and pressure without cross-interference was achieved using a single material in both air and underwater environments.
The sensor maintains stable signal output under prolonged underwater operation, mechanical bending, electromagnetic interference exposure, and even direct flame contact, demonstrating exceptional environmental resilience.
✓ 已验证
产品关联
DOI
PubMed
高影响因子
JOURNAL OF MATERIALS SCIENCE-MATERIALS IN ELECTRONICS
·
2026
·Vol. 37
·期 18
·1407
·
IF 3.2
Jiang Zheng,Yang Xiaoliang,Xiao Siguo
Cr 3+ /Bi 3+ co-doped and Cr 3+ /Yb 3+ co-doped La 2 LiSbO 6 phosphors have been synthesized via a high-temperature solid-state method, respectively. La 2 LiSbO 6 : Cr 3+ gives a broadband emission peaking at 855 nm under 671 nm excitation. Partial substitution of La 3 ⁺ ions by Bi 3+ ions induces lattice distortion in the La 2 LiSbO 6 host and weakens the crystal field strength of Cr 3+ , leading to the red shift of Cr 3+ emission. The Cr 3+ emission peak shifts from 855 to 900 nm with Bi 3+ concentration increasing from 0 to 0.07 mol %. The increased lattice distortion also improves the local environment of Cr 3+ , thereby resulting in a threefold increase in luminescence intensity and a 25.8% increase in quantum yield. When the Yb 3+ ions are introduced, the emission peak can be further tuned from 855 to 1000 nm directly, induced by energy transfer from Cr 3+ to Yb 3+ ions. It is proven that quadrupole–quadrupole interaction is responsible for the energy transfer from Cr 3+ to Yb 3+ in the La 2 LiSbO 6 host. Moreover, the introduced Yb 3+ also largely improves the thermal stability of the phosphor. The work might provide meaningful reference for the design and development of highly efficient Cr 3+ -doped luminescent materials.
✓ 已验证
DOI
高影响因子
JOM
·
2026
·
IF 2.3
Deng Chuheng,Qin Yufeng,Shen Yi,Rao Longshi,Wang Shuangxi
Metallized ceramic substrates are essential for power electronics, offering superior thermal and electrical conductivity. However, traditional metallization techniques, such as thick printed copper (TPC), face significant challenges, including weak bonding strength, high sintering temperatures, and complications associated with glass frit, which ultimately compromise device reliability and performance. To address these issues, this study presents an efficient method for fabricating high-performance copper (Cu) films on Al 2 O 3 ceramic substrates using low-temperature, pressureless sintering. By incorporating a magnetron-sputtered copper interlayer combined with printed copper paste, we eliminate the need for glass frit, a conventional component that often introduces defects. Through careful optimization of copper powder synthesis and paste formulation, we achieved dense, low-porosity Cu films sintered at just 300°C, which demonstrate exceptional electrical conductivity (1.7 × 10 7 S m −1 ) and shear strength (31.5 MPa). The sputtered copper interlayer significantly enhances the adhesion between the copper film and the ceramic substrate, minimizing delamination and improving mechanical integrity when compared to traditional sintering methods. This approach addresses key challenges in power device packaging, providing a cost-effective, reliable solution for low-temperature, high-performance interconnections. The results have wide-reaching implications for advancing electronic packaging, especially in power electronics, by enabling durable, efficient, and scalable manufacturing processes.
✓ 已验证
产品关联
DOI
高影响因子