VACUUM
·
2023
·
IF 4
Heyan Yuan,Fang Wang,Xin Lin,Xin Shan,Kaiyi Zhang,Jixiang Zhong,Yujing Ji,Ke Shan,Yangyang Xie,Kai Hu,Zhitang Song,Kailiang Zhang
As an emerging ultrathin semiconductor material, Bi 2 O 2 Se has shown outstanding performance in fields of electronics, optoelectronics and ultrafast optics. High performance Bi 2 O 2 Se nanosheets were desperately needed for further foundational research and practical applications. However, their synthesis has not yet been completely developed. In this paper, high quality Bi 2 O 2 Se nanosheets were efficiently obtained by sdjusting synthesis pressure. The uniform nucleation of Bi 2 O 2 Se nanosheets on substrates was achieved, put forward the nucleation mechanism of Bi 2 O 2 Se nanosheets. The near-infrared (NIR) optoelectronic properties of multilayer Bi 2 O 2 Se nanosheets were systematically investigated. Photodetectors were constructed based on Bi 2 O 2 Se nanosheets of different thicknesses and the near-infrared (NIR) photoelectric properties of Bi 2 O 2 Se-based photodetectors with the highest responsivity were systematically investigated. The multilayer Bi 2 O 2 Se nanosheets exhibit sensitive responsivity to the NIR, including high responsivity (∼825 A/W), high external quantum efficiency (∼1.25 × 10 5 %) and high detectivity (6 × 10 10 Jones). These results suggest that devices based on multilayer Bi 2 O 2 Se nanosheets may have great potential for future applications in ultrafast, high-sensitivity NIR optoelectronic devices.
研究领域:
材料科学
·
光学
·
电子工程
✓ 已验证
DOI
高影响因子
ELECTROCHIMICA ACTA
·
2019
·
IF 5.383
Xiaokai Hao,Jingchun Jia,Ying Chang,Meilin Jia,Zhenhai Wen
The design of sensitive and fast-response of catalysts are very important for non-enzymatic glucose biosensors. In this work, monodisperse copper selenide (Cu 2-x Se) nanoparticles (NPs) are prepared by thermal decomposition of copper acetylacetonate (Cu(acac) 2 ) in the solution of oleylamine, then selenide at different temperatures with reduce graphene oxide (RGO) as support. These Cu 2-x Se NPs are active catalysts as ultrahigh sensitive non-enzymatic glucose biosensor, which exhibits sensitivity of 536 μA mM −1 cm −2 , a wide linear range up to 3.375 mM and a low detection limit of 0.05 mM (S/N = 3). Based on good selectivity, sensitivity and the ability of anti-interference, the Cu 2-x Se NPs will be the promising sensor for enzyme-free monitoring of glucose.
研究领域:
材料科学
·
生物医学工程
·
分析化学
✓ 已验证
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2022
·
IF 6.371
Na Li,Qihua Zhou,Jing Lin,Yanzhen Lu,Zhiguo Hou,Yitai Qian
Molybdenum diselenide (MoSe 2 ) have attracted much attention as an anode material for lithium/sodium ion batteries due to its specific layered structure. Here, highly-uniform MoSe 2 nanoparticles are successfully synthesized via a one-pot hydrothermal method with addition of polyvinyl pyrrolidone (PVP) following by calcination treatment. PVP serves as a surfactant preventing the over-agglomeration of MoSe 2 nanosheets and contributing to the well-organized accumulation of MoSe 2 nanosheets into nanoparticles . When evaluated as anode for lithium ion batteries , the MoSe 2 nanoparticles show enhanced cycle stability and rate performance comparing to the MoSe 2 bulk prepared without addition of PVP. After 200 cycles, the MoSe 2 nanoparticles remain a specific capacity of 573.9 mAh g −1 at a rate of 200 mA g −1 . Meanwhile, MoSe 2 nanoparticles also display good sodium storage performance. Under the current density of 500 mA g −1 , MoSe 2 nanoparticles exhibit reversible capacity of 374.9 mA h g −1 after 100 cycles.
研究领域:
材料科学
·
电化学
·
纳米科技
·
能源存储
·
无机合成
✓ 已验证
DOI
高影响因子
APPLIED SURFACE SCIENCE
·
2020
·
IF 6.182
Yu You,Mengli Wei,Likun Yang,Jingwen Wang,Yongxing Zhang,Jun Xu
The practical applications of high-performance lithium-sulfur batteries are severely hindered by the insulating nature of sulfur and intractable shuttling of the polysulfide intermediates. In this work, we report a novel MoSe 2 @rGO cathode coating consisting of two-dimensional MoSe 2 and reduced graphene oxide (rGO) as a multifunctional barrier to suppress polysulfide shuttling. Few-layered MoSe 2 nanosheets are in situ grown on the rGO surface by basal plane contact. Besides, some cotton-like MoSe 2 nanospheres assembled from porous nanosheets are decorated on the surface of rGO nanosheets. Benefitted from the strong chemical adsorption of polar MoSe 2 and excellent electrical conductivity of rGO, the MoSe 2 @rGO coatings exhibit highly efficient polysulfide anchoring and significantly enhanced electrocatalytic chemistry. Moreover, the MoSe 2 @rGO cathode coatings are much superior to its separator coatings in the recycling of the adsorbed active materials because of good interfacial conductivities. The cell with the MoSe 2 @rGO cathode coating delivers a high reversible capacity up to 1216 mAh g −1 at 0.2 C and outstanding cycling stability with a low capacity fading rate of 0.03% at 1 C over 1000 cycles.
研究领域:
材料科学
·
电化学
·
能源存储
·
纳米材料
·
电池技术
✓ 已验证
DOI
高影响因子
JOURNAL OF ALLOYS AND COMPOUNDS
·
2022
·
IF 6.371
Qiuping Zhou,Dawei Wang,Lubin Ni,Huaihao Zhang,Jing Zhao
Recently, aluminum-based batteries have received extensive attention from researchers because of their advantages over other metals-based batteries in terms of cost, energy density , and safety performance. Herein, we synthesized willow leaf-shape ReSe 2 @C as the positive electrode of aluminum batteries. ReSe 2 , with anisotropic crystal structure, is encapsulated in carbon using weak interlaminar van der Waals force. Its low lattice symmetry increases the ion/electron adsorption sites and reduces the energy barrier for ion intercalation into ReSe 2 layers. The electrochemical analysis and X-ray photoelectron spectroscopy of ReSe 2 @C have ascertained that AlCl 4 - is intercalated/embedded in host material during charging/discharging. The specific discharge capacity of ReSe 2 @C remains 88 mA h g −1 after 1000 cycles at the current density of 100 mA g −1 , with a high Coulomb efficiency of 98%.
研究领域:
材料科学
·
电化学
·
能源存储
·
纳米材料
·
无机化学
✓ 已验证
DOI
高影响因子
Biosurface and Biotribology
·
2023
·
IF 0
Rong Hu,Xiao Wang,Lu Han,Xiong Lu
Selenium (Se), a well-known essential element in human health, plays a vital role in regulating metabolism owing to its antioxidative nature. However, organic Se compounds are toxic and cannot be used for biomedical applications. Selenium nanoparticles (SeNPs) exhibit low biological toxicity and high bioavailability; however, they are prone to aggregation and are extremely unstable, thereby diminishing their bioactivity and bioavailability. To overcome these limitations, ultra-small, highly stable, and bioactive SeNPs were synthesised based on an in-situ hybridisation strategy by using polyphenol-grafted-chitosan (GA-CS) to control and restrict crystal growth of Se nanoparticles. The resultant GA-CS@nSe exhibited an average particle size of ∼30 nm and was highly stable in aqueous solutions. In addition, GA-CS@nSe displayed improved biocompatibility and enhanced antioxidative activity. Taken together, the authors provide a basis for polyphenol-mediated construction of Se-based particles with increased bioactivity.
研究领域:
纳米技术
·
材料科学
·
生物医学工程
·
药学
✓ 已验证
DOI
OPTICAL MATERIALS
·
2020
·
IF 2.779
Guonan Cui,Yanchun Yang,Ruilan Chen,Chengjun Zhu
Cations substitutions are known to make much significant contribution on achieving the high-quality kesterite Cu 2 ZnSn(S,Se) 4 thin films . And the optimal ratios of Mn, Ni and Co substitutions are reported to be ~0.05, belong to the low doping to reduce their defect density , which looks like to some extent the effect of Na doping. In this study, learning the research experience of alkali metal doping, we introduced the extra trace Mn 2+ ion into the precursor solution without affecting the compositions of other elements (i.e. Cu, Zn, and Sn), and the effect of trace addition on properties of the absorber layer was also studied. It was discovered that crystalline, electrical properties, and hole carrier concentration of Cu 2 ZnSn(S,Se) 4 thin films increased with an increase of Mn incorporation, and the best doping ratio of Mn/(Cu + Zn + Sn) was considered to be 0.03. In addition, the effect of extra trace Mn-doping on the film thickness and elemental compositions of Cu 2 ZnSn(S,Se) 4 absorber layer were studied in detail.
研究领域:
材料科学
·
半导体物理
·
薄膜制备
·
光伏材料
·
固体化学
✓ 已验证
DOI
高影响因子
ZEITSCHRIFT FUR ANORGANISCHE UND ALLGEMEINE CHEMIE
·
2020
·Vol. 647
·期 9
·1025-1030
·
IF 1.24
Yihan Wang,Hu Zhou,Jinghao Xiao,Aihua Yuan
Metal selenides as anode materials of lithium-ion batteries (LIBs) has received considerable attention recently. In order to boost the electronic conductivity and alleviate the volume change of electrode materials upon the cycles, a facile strategy is employed in this work, where Prussian blue analogue (PBA) nanocubes are encapsulated into three-dimensional (3D) network of graphene aerogel (GA), followed by a high-temperature selenization treatment to isolate the composite of FeCoSe 2 @GA. The composite can be directly employed as free-standing anode materials of LIBs. Studies reveal that the FeCoSe 2 @GA electrode demonstrates an intriguing cycle stability and rate capability with a specific capacity of ∼500 mAh g −1 at 100 mA g −1 after 100 cycles. The outstanding lithium-storage properties can be attributed to the 3D porous feature as well as the strong confinement effect of GA for FeCoSe 2 particles, which provides a large number of ion-exchange channels, and prevents the severe agglomeration and large volume expansion of active particles during the charge/discharge process.
研究领域:
材料科学
·
能源存储
✓ 已验证
DOI
高影响因子
Progress in Natural Science-Materials International
·
2021
·
IF 3.607
Cheng Lin,Liuzhang Ouyang,Renzong Hu,Jun Liu,Lichun Yang,Huaiyu Shao,Min Zhu
To promote substantially the performances of red phosphorous (P) anode for lithium and sodium-ion batteries, a simple plasma assisted milling (P-milling) method was used to in-situ synthesize SeP 2 /C composite. The results showed that the amorphous SeP 2 /C composite exhibits the excellent lithium and sodium storage performances duo to the small nano-granules size and complete combination of selenium (Se) and phosphorous (P) to generate Se–P alloy phase. It was observed that inside the granules of SeP 2 /C composite the nanometer size of the SeP 2 particles ensured the fast kinetics for Li + and Na + transfer, and the amorphous carbon wrapping the SeP 2 particles relieved volume expansion during lithium/sodium storage processes and enhances electric conductivity. Therefore, the SeP 2 /C electrode retained reversible capacities of 700 mA h g −1 at 2 A g −1 after 500 cycles and 400 mA h g −1 at 0.5 A g −1 after 400 cycles as anode for LIBs and SIBs, respectively. The result proves that the amorphous SeP 2 /C composite can be a new type of anode material with great potential for lithium and sodium-ion batteries.
研究领域:
材料科学
·
电化学
✓ 已验证
DOI
高影响因子
SOLAR ENERGY MATERIALS AND SOLAR CELLS
·
2023
·
IF 6.9
Haoyu Xu,Yuzhou Sun,Zhou Shen,Qing Zhou,Qingyun Zhu,Haifeng Gao,Chao Gao,Xiaoyun Teng,Yu Wei
In this paper, we prepared Na–K co-doped Cu 2 ZnSn(S,Se) 4 (CZTSSe) films by solution method. By optimizing the distribution of the K-doping (uniform or localized K-doping) in the precursor films, the efficiencies of CZTSSe solar cells were improved. The effect of the K-doping distribution on the properties of CZTSSe films and solar cells were investigated. Compared to the solar cells without K-doping, the uniform K-doping in the precursor film increased the solar cell efficiency from 10.4% to 11.7%. In comparison, the localized K-doping in the bottom and in the top of the precursor films yielded solar cells with efficiencies of 12.4% and 10.1%, respectively. It was determined that the K-doping distribution primarily had an influence on carrier recombination in the depletion regions of CZTSSe solar cells. Whereas k-doping at the top of the precursor film greatly enhances the carrier recombination in the depletion region, the bottom doping has the opposite effect. The reason could be that the variation of the K-doping distribution modified the crystallization of the CZTSSe films. As the result, the defect properties of the CZTSSe films were altered. Moreover, the effect of the bottom K-doping on the back contact properties of CZTSSe solar cells was investigated by impedance spectroscopy . Though the K-doping can reduce the back contact barrier of the solar cell, the back contact barrier still achieved the height of 228 meV. The results indicated that the back contact barrier would be an important limiting factor for the efficiency of CZTSSe solar cell.
研究领域:
材料科学
·
能源科学
✓ 已验证
DOI
高影响因子
CERAMICS INTERNATIONAL
·
2017
·
IF 2.986
Ye Lian,Jinqiu Zhang,Xiaochuan Ma,Peixia Yang,Maozhong An
Three-dimensional ordered macroporous (3DOM) CuIn x Ga 1−x Se 2 (CIGS) film is synthesized by one-step galvanostatic electrodeposition based on polystyrene templates from a special mixture of ionic liquid 1-butyl-3-methylimidazolium tetra-fluoroborate and ethanol. X-ray diffraction pattern , Raman spectroscopy and transmission electron microscopy present the CIGS film has ideal chalcopyrite crystallization. 3DOM CIGS film with high Ga content has photochemical activity and good photo-stability, its band gap is 1.34 eV. This is a simple, feasible and additive free method without selenization process to synthesize 3DOM CIGS film, the film is qualified and available for absorber-layer fabrication or other fields.
研究领域:
材料科学
·
化学工程
✓ 已验证
DOI
高影响因子
CHEMISTRY OF MATERIALS
·
2020
·
IF 9.567
Xuelian Yu,Yuxuan Wu,Jiayi Cui,Yue Ran,Wei Lin,Li-Min Liu,Jinhua Ye,Yihe Zhang,Andreu Cabot
Strain engineering has become an emerging strategy to tailor the performance of nanocatalysts. However, current strained catalysts overwhelmingly rely on stresses originated at catalyst–support interfaces. Self-standing strained nanostructures are extremely challenging to produce, and thus their impact on catalytic and photocatalytic activities remains largely unknown. Herein, we propose a ligand-based colloidal strategy for the one-step growth of bended metal chalcogenide nanoplates with a built-up strain. This strategy is based on the seeded growth of strained nanostructures from sacrificial seeds which provide a proper lattice mismatch. We demonstrate this strategy for the synthesis of strained orthorhombic SnSe and SnS nanoplates from rock salt SnS seeds. We probe not only the presence of atomic distortions in the periodic lattice but also its coupling with the generation of a large density of selenium vacancies. Geometrical phase analysis evidences the formation of a strain field in self-bended SnSe nanoplates, with a maximum tensile strain up to 12%. Theoretical and experimental results further reveal that the strain-related selenium vacancies strongly affect the electronic structure of SnSe and facilitate the mobility of photogenerated charge carriers, which result in a significantly improved photoelectrochemical activity. The strategy presented here opens a new avenue for precisely tuning semiconductor functionalities via strain engineering.
研究领域:
材料科学
·
化学工程
·
纳米技术
✓ 已验证
DOI
高影响因子
危险品化学品经营许可证（带存储）