文献检索

查找使用阿拉丁产品的科研文献

检索与阿拉丁产品相关的同行评审论文、DOI、PubMed 编号、期刊、作者、CAS 号及研究领域。

科研影响力快照

与阿拉丁产品相关的已发表科研成果

在搜索之前,这些指标可帮助访客快速了解产品关联科研的规模与质量。

347,389+ SCI 论文 与阿拉丁产品引用相关
2,303,681.05 总影响因子 匹配文献记录中影响因子的总和
81.20 最高期刊影响因子 匹配期刊中的最高 IF
6.63 平均期刊影响因子 匹配文献的平均 IF

参考指标 指标基于阿拉丁文献引用数据库及期刊影响因子记录。文献关联仅供科研参考,请以原始文献为准。

产品列表

视图 列表 网格

显示第2149至2160个,产品总数347,389个

切换升序
BIORESOURCE TECHNOLOGY · 2026 · IF 8.2

Co-recovery of cellulose nanofibers and lignin from rice straw for high-performance reusable insulating aerogels

Phuoc-Cuong Le,Xuan Kien Bui,Dinh Ngo Vu,Thi Thao Minh,Tan Nhat,Dinh Nhi Bui

Rice-straw-derived CNF/lignin aerogels were developed as microwave-passive insulating cores. • CNF/L10 provided the best balance of porosity, strength, moisture tolerance, and insulation. • Low thermal conductivity and humid-state dielectric loss supported reduced wall self-heating. • CNF/L10 prototype walls reduced outer sidewall temperature from 62.7 to 45.9 °C. • CNF/L10 retained mechanical stability and microwave transmittance after 1000 wash–reheat cycles. Rice-straw-derived cellulose nanofiber/lignin (CNF/lignin) aerogels were developed as microwave-passive insulating cores for reusable food-container walls. Cellulose and lignin co-recovered from Vietnamese rice straw were reassembled into aerogels containing 0–20 wt% lignin to define a practical formulation window for microwave-reheatable packaging. Moderate lignin addition preserved the cellulose I framework and improved the balance between pore-wall integrity, moisture tolerance, thermal insulation, and dielectric stability. Among the tested samples, CNF/L10 gave the best overall performance, with a density of 0.025 ± 0.001 g cm −3 , porosity of 98.33 ± 0.07%, compressive modulus of 74.6 ± 3.7 kPa, compressive strength of 32.7 ± 1.8 kPa at 70% strain, water contact angle of 79.2 ± 2.8°, and moisture absorption of 49.8% after 48 h at 75% RH. Its thermal conductivity remained low, increasing only from 0.0288 ± 0.0009 W m − 1 K − 1 at 50% RH to 0.0336 ± 0.0011 W m − 1 K − 1 at 75% RH. At 2.45 GHz, CNF/L10 showed ε′ = 1.61, ε″ = 0.053, and tanδ = 0.0329 at 50% RH, and ε′ = 1.93, ε″ = 0.129, and tanδ = 0.0668 at 75% RH. In a PP/aerogel/PP prototype wall, CNF/L10 reduced the outer sidewall temperature from 62.7 ± 1.2 °C to 45.9 ± 0.9 °C while maintaining food-center heating. After 1000 wash–reheat cycles, it retained 86.8% modulus, 85.0% strength, and 87.8 ± 1.5% microwave transmittance, with overall migration below 10 mg dm −2 . These results support CNF/L10 as a promising bio-based insulating core for lower-plastic microwave food-packaging prototypes. Download: Download high-res image (294KB) Download: Download full-size image

CAS / MDL: 7758-19-2
✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
Crystals · 2026 ·Vol. 16 ·期 7 ·471 · IF 2.9

Effect of Aging Treatment on the Corrosion Behavior of Selective Laser Melted Fe-30Mn-8Al-1.5C-2.5Ni Lightweight Steel

Fufei Deng,Hui Yang,Changling Zhuang

Selective laser melting (SLM) can effectively suppress metallurgical defects inherent to conventional manufacturing; however, subsequent aging treatments essential for engineering applications introduce secondary precipitates that alter the electrochemical homogeneity of the matrix. The underlying mechanism by which such precipitation behavior governs corrosion resistance remains elusive. In this study, a Fe-30Mn-8Al-1.5C-2.5Ni steel was investigated to elucidate the corrosion morphology and electrochemical behavior of the as-built, 450 °C-aged, and 750 °C-aged specimens during immersion in a 3.5 wt.% NaCl solution. The results demonstrate that the inherent Mn microsegregation and high-density subgrain boundaries induced by SLM trigger preferential localized anodic dissolution on the surface of the as-built sample, culminating in the formation of a loose, porous manganese oxide product layer. Aging treatment at 450 °C induces extensive precipitation of κ-carbides within grain interiors and along grain boundaries, accompanied by localized depletion of Al and Mn at the phase interfaces. A pronounced micro-galvanic coupling established between the κ-carbides and the adjacent Al-depleted zones directly compromises the continuity of the passive film, thereby further deteriorating the corrosion resistance. In contrast, aging at 750 °C relieves the residual stress and eliminates the as-built elemental microsegregation. The resulting compositional homogenization of the matrix reduces the localized electrochemical driving force, which promotes a uniform reaction of Al at the surface to construct a continuous, compact Al-rich passive film, thereby sustaining the highest charge-transfer resistance during long-term immersion. This work elucidates the correlation among the intrinsic defects of SLM, aging-induced solute-depleted zones, κ-carbide precipitation, and localized micro-galvanic corrosion, providing a fundamental basis for tailoring the microstructure and corrosion resistance of additively manufactured lightweight steels.

CAS / MDL: 7647-14-5
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF APPLIED POLYMER SCIENCE · 2026 · IF 3.1

Highly Transparent Superhydrophobic Photovoltaic Coating With Alkali-Induced Durability Enhancement

Zibo Du,Wen Zhao,Jianlei Qi,Shuyu Wang,Yang Su,Yanping Wang

Surface contamination on photovoltaic glass severely degrades its power-generation efficiency, thereby making the development of transparent anti-soiling coatings an important research direction. Herein, a poly (methylmethacrylate)/1H,1H,2H,2H-perfluorooctyltriethoxysilane/SiO 2 (PMMA/PFOTS/SiO 2 ) organic–inorganic hybrid transparent superhydrophobic anti-fouling coating is developed via a one-step sol–gel method. The coating exhibits a stable Cassie-Baxter state with high water contact angle (155.2° ± 1.1°) and a low sliding angle (4.8° ± 0.7°), demonstrating excellent superhydrophobic characteristics. Optical tests demonstrate an average transmittance of 87.6% in the 400–2500 nm range and only 8.3% external quantum efficiency (EQE) attenuation at 800 nm compared to photovoltaic devices, significantly outperforming commercial superhydrophobic coatings (58.3% attenuation). This enables synergistic gains in dust resistance and photon capture efficiency. Additionally, after 24 h immersion in alkaline solution, the coating hydrophobicity is enhanced, with WCA increasing to 165.1° ± 1.4°. We believe that the designed superhydrophobic coating with integrated functionalities of self-cleaning, high transmittance, and alkali-induced self-enhancement can provide important solutions for maximizing the long-term power generation efficiency of photovoltaic glass in complex outdoor environments.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
CHEMICAL ENGINEERING SCIENCE · 2026 · IF 5.1

Insights into simultaneous removal of nitrate and carbamazepine using UV/sulfite process: performance and mechanisms

Xuxuan Lu,Xinyu Zhou,Huiyan Wang,Ying Zhang,Dachang Dong,Lijie Xu

Nitrate is always present as the concomitant component during the advanced treatment of refractory organic emerging contaminants. The simultaneous achievement of effective denitrification is an ideal goal for environmentally friendly treatment, especially for those nitrogen-containing compounds. Herein, the performance and mechanisms for simultaneous removal of CBZ and nitrate by UV 254nm /S(IV) process were investigated. Results demonstrated that CBZ and NO 3 – - N could be efficiently removed together, and denitrification was mainly contributed by e aq - , while CBZ degradation was driven by e aq - (55.4%) and •OH (30.4%) collectively. Moreover, the presence of nitrate exerted more significant influences on CBZ degradation than the competition nitrate faced on its own. The removal of CBZ and nitrate both increased with the rise in solution pH and the decrease in their respective initial concentrations. However, the denitrification was accelerated by increasing sulfite concentration while CBZ degradation was obtained at an optimum sulfite concentration. Although nitrate could quench the hydrated electrons to impede CBZ degradation, the •OH radicals produced by nitrate photolysis could compensate partially for the loss. The final product of nitrate was almost completely the nitrogen gas, while both the reduction pathway and oxidation pathway of CBZ degradation were proposed based on DFT calculation and UPLC/MS analysis. The detoxification advantages of CBZ degradation were also revealed from the UV/sulfite process, and the intermediates obtained from reduction reactions generally showed lower toxicity than those from oxidation reactions. This study may provide insights into developing efficient and environmentally friendly advanced methods for the treatment of emerging contaminants.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
ANALYTICAL CHEMISTRY · 2026 ·Vol. 98 ·期 29 ·21624-21633 · IF 7.3

Photographic Physi-Luminescence Assay Based on a Persistent Luminescence Nanoprobe

Zong Ziang,Qu Chaomin,Ding Leping,Ma Xiao,Abulipizi Gulizhabaier,Fang Yanlun,Li Li,Xie Wei,Wang Jiajia,Zhou Juanjuan,Li Zhanjun

Chemi- or bioluminescence assays have broad applications in biomedical analysis, yet they still suffer from a flash effect or difficulty in maintaining time synchronization during high-throughput assays. Persistent luminescence (PersL) nanoprobes are able to emit photons for a rather long time without any chemical reactions and have promising applications in developing a physi-luminescence assay. Herein, SiO 2 /Zn 2 SiO 4 :Mn,Yb,Ge nanoparticles (MYG, Zn/Si/Mn/Yb/Ge molar ratio, 2/15/0.003/0.060/0.100) were synthesized with PersL properties at 525 nm. Mesoporous silica nanoparticles were used as a nanotemplate to control the size and morphology, which allowed for gram-scale production (1.1277 g). Ge was found to be an efficient codopant to realize the enhanced PersL of MYG. A hydrophobic azo dye, Sudan III, was loaded onto the MYG surface to form a quenched MYG-S nanoprobe. Under 254 nm UV illumination, Sudan III was oxidized by H 2 O 2 , and PersL was recovered. The “OFF–ON” PersL property of MYG-S was applied to develop a physi-luminescence assay method for H 2 O 2 , glucose, and glucose oxidase in serum. As the PersL of the samples in a 96-well plate was activated by simultaneous UV illumination rather than by adding chemicals, high-throughput photographic luminescence analysis was realized with accuracy and repeatability. Our research indicates the promising applications of PersL nanoprobes in developing a physi-luminescence assay.

✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
Polymers · 2026 ·Vol. 18 ·期 14 ·1748 · IF 5.8

Preparation and Performance Evaluation of a Biodegradable Gel for Deep Coal Reservoir Drilling Fluids

Jiang Xin,Xinyu Hao,Zongkai Qi,Gang Chen,Wei Wang,Zenglong Wang,Jinliang Han,Jiafeng Jin,Gengshu Wang

Deep coal reservoirs are characterized by abundant microfractures and cleats, resulting in frequent wellbore instability during long horizontal drilling operations. To address this issue, a biodegradable gel plugging agent (XZ) was synthesized from acrylamide (AM) and carboxymethyl cellulose (CMC) via an orthogonal crosslinking strategy. The gelation behavior, swelling capacity, rheological properties, mechanical strength, thermal and salt resistance, plugging performance, self-degradation characteristics, reservoir protection capability, and drilling-fluid compatibility of XZ were systematically evaluated. The results showed that XZ formed a stable three-dimensional crosslinked network with good thermal stability (T0= 116 °C, T1/2= 445 °C). The synergistic effects of covalent and ionic crosslinking endowed the gel with high swelling capacity, mechanical strength, and plugging ability. XZ exhibited excellent temperature and salinity tolerance, with a degradation rate exceeding 90% after 5 days. After degradation, the filter cake became significantly thinner and core permeability recovery reached approximately 80%, demonstrating effective reservoir protection. Moreover, XZ significantly increased drilling-fluid viscosity, reduced fluid loss, and enhanced plugging performance. The XZ-based drilling fluid system integrates efficient plugging, self-deplugging, and reservoir protection functions, providing a promising solution for safe and efficient drilling in deep coalbed methane reservoirs.

CAS / MDL: 110-26-9 79-06-1
✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
Small · 2026 · IF 11.8

Stable Photothermal Conversion Fillers Enable Subzero-Temperature Applications of PEO-Based Solid-State Lithium Batteries via In Situ Self-Heating

Yihui Sang,Long Hu,Yuan Li,Kaiqiang Song,Hongdi Hu,Lingshu Dong,Yucheng Wen,Yuxuan Liu,Renzong Hu

Low-temperature operational reliability remains a critical bottleneck for all-solid-state batteries (ASSBs). Polyethylene oxide (PEO)-based solid-state electrolytes (SSEs), the most widely studied SSE system, typically exhibit ionic conductivities as low as 10 −6 S cm −1 at ambient temperature, necessitating battery operation at 60°C–80°C. This external heating requirement consumes extra electrical energy and severely limits the application of PEO-based ASSBs under low-temperature conditions. Here, we introduce lithiated poly(3,4-dioxythiophene) (LiPHT) photothermal conversion filler into PEO-based SSEs, which significantly enhances the ionic conductivity to 1.34 × 10 −4 S cm −1 while simultaneously broadening the electrochemical window to 4.55 V vs. Li/Li + at room temperature. By utilizing the PEO-LiPHT composite layer as both a “heater” and the electrolyte layer within the transparent battery, the device exhibits efficient photothermal conversion and rapid light-induced heating. Benefiting from the in situ photothermal self-heating effect that elevates the actual internal cell temperature to the optimal operating range of PEO electrolytes, the ASSB demonstrates a high discharge capacity of 131.3 mA h g −1 at 0.5 C under an ambient temperature of −15°C. This work offers a viable pathway to circumvent the intrinsic low-temperature limitation of PEO-based electrolytes, facilitating the development of high-performance ASSBs for subzero-temperature applications.

✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
DYES AND PIGMENTS · 2026 · IF 3.9

Green synthesis of poly(lactic acid)-based nitrogen-doped carbon quantum dots and their application as multifunctional fluorescent probes for the detection of environmental pollutants

Qun-Fang Wang,Yun Li,Shi-Hang Yang,Zi-Qi Xiao,Zong Li,Bei-Ning Xiao

Green synthesis of PLA-CQDs as PLA-based N-doped carbon quantum dots is developed. • PLA-CQDs can exhibit quick fluorescence quenching for Fe 3+ and three NAC explosives. • PLA-CQDs probe can have lower LODs, e.g., 57.9 nM (for PA, a typical NAC explosives). • Mechanistic studies show that the quenching reason of Fe 3+ and three NACs is different. • Detection in real water samples and visual sensing with test strips can be achieved. In this study, biobased polymer material poly(lactic acid) (PLA) was used as a green carbon source and ethylenediamine as a nitrogen source to successfully prepare nitrogen-doped carbon quantum dots PLA-CQDs with excellent performance via a one-step hydrothermal method. The morphology, structure, and optical properties of the carbon quantum dots were characterized by using transmission electron microscopy, X-ray photoelectron spectroscopy, FT-IR, and fluorescence spectroscopy. The results show that the PLA-CQDs exhibit a uniform particle size distribution with an average diameter of 4.81 ± 0.89 nm, being rich in amino, hydroxyl, and other functional groups on their surface. Under 365 nm UV lamp irradiation, they can emit bright blue fluorescence with a fluorescence quantum yield of 11.09%. Experimental results demonstrate that the carbon quantum dots have a highly selective fluorescence quenching response to Fe 3+ within 10 s, while also showing excellent recognition ability towards three nitro aromatic compounds (NACs), namely picric acid, p -nitrophenol, and 2,4-dinitrophenol. However, when two types of target analytes coexist, the fluorescence signal overlap occurs, thus the probe is currently only suitable for the detection of a single target analyte. The lower detection limits can reach 3.92 × 10 −7  M (for Fe 3+ ), 5.79 × 10 −8  M (for picric acid), 5.56 × 10 −7  M (for p -nitrophenol), and 1.79 × 10 −7  M (for 2,4-dinitrophenol), respectively. The probe has been applied to the detection of target analytes in real water samples, with spiked recoveries ranging from 94.9% to 104.9% and relative standard deviations below 2.5%, indicating good accuracy and reliability. This study not only achieves high-value utilization of biomass resources by using PLA as a carbon source to prepare multifunctional fluorescent probes, but also provides a new technical approach for the rapid detection of environmental pollutants such as heavy metal ions and NACs in water. Download: Download high-res image (346KB) Download: Download full-size image

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
Small · 2026 · IF 11.8

BandGap Modulated Charge Gating of Semiconductor Coatings Stabilizes Zinc Metal Anodes

Jiadong Wu,Linyu Yang,Kunjie Zhu,Ablat Abliz,Shuying Wang,Hongmei Zhang,Haibing Li,Hongyu Mi,Anqiang Pan

Hydrogen evolution reaction (HER) and uncontrolled dendrite growth remain persistent challenges for aqueous Zn-ion batteries (AZIBs). In this study, the Y element is utilized to adjust the bandgap width of the anode coating, thereby serving as electron transfer gating and consequently suppressing HER from a dynamic perspective. The Gibbs free energy ( ΔG H* ) data for H * adsorption reveal that the presence of the Y can hinder the desorption of H 2 from the surface of the semiconductor coating. It effectively restrains HER from a thermodynamic viewpoint. Furthermore, the improved zincophilicity of the amorphous wide-bandgap semiconductor coating offers a multitude of uniform nucleation sites for Zn 2+ deposition. A balance between H * adsorption and Zn 2+ affinity is achieved by this wide bandgap semiconductor, enabling strong HER inhibition and highly efficient Zn-induced deposition. The symmetric cell achieves stable cycling for over 6700 h at 2 mA cm −2 and 1 mAh cm −2 . Even under a high current density of 10 mA cm −2 and 5 mAh cm −2 , a cycle life of 1200 h is maintained. The Zn–V full cell exhibits a cycling lifespan of 3800 cycles at 5 A g −1 .

✓ 已验证 产品关联 DOI PubMed 高影响因子
查看原文 查看 PubMed
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY · 2026 ·Vol. 46 ·期 16 ·118692 · IF 6.3

An integrated method for simultaneously achieving efficient SiC coating preparation and C/SiC matrix densification

Chengfan Yuan,Qiang Gao,Xinhui Geng,Wuju Wang,Liancai Xun,Puzheng Zhang,Ping Hu

C/SiC composites known for excellent high-temperature resistance and favorable mechanical properties are promising thermal protection materials. However, pores and microcracks from traditional processes significantly degrade their high-temperature oxidation resistance. Herein, we propose an integrated technique that combines coating preparation with matrix densification. Using this approach, a uniform SiC coating (50 μm thickness) was successfully prepared on C/SiC composites, while simultaneously achieving matrix densification. SiC-C/SiC composites exhibited superior oxidation resistance at 1000–1600 ℃. After 1600 ℃ oxidation, the mass loss rate decreased from 16.8% to 6%, and flexural strength (246 ± 24 MPa) was 2.5 times that of C/SiC composites (91 ± 37 MPa). Additionally, SiC-C/SiC composites demonstrated excellent oxidation and ablation resistance at 1600–1800 ℃ compared with conventional C/SiC composites. This technique allows component design to be tailored to practical requirements, providing a feasible method for efficient preparation of coatings.

CAS / MDL: 64-17-5 9002-98-6
✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
Water · 2026 ·Vol. 18 ·期 12 ·1484 · IF 3.5

Contrasting Dissolved Organic Carbon Cycling in Open and Closed Karst Reservoirs Water: Evidence from Dual Carbon Isotopes (δ13C–Δ14C)

Xia Yu,Hao Liu,Bingyang Dai,Xuran Liu,Zilin Mei,Chao Ma,Chengzhi Yang,Mingyu Shao,Yanling An

Reservoirs in karst regions exhibit significant carbon sink potential; however, how different reservoir types influence carbon sequestration remains poorly understood. In this study, dual carbon isotopes (δ13C–Δ14C) were applied to trace dissolved organic carbon (DOC) sources in an open reservoir (Aha Reservoir, AHR) and a closed reservoir (Guanshan Lake, GSL) in southwestern China, and to evaluate their carbon sequestration potential. DOC concentrations in GSL were significantly higher than those in AHR (4.14 ± 0.28 mg/L > 3.37 ± 0.30 mg/L) (p< 0.01), along with lower δ13C values (−30.34 ± 0.51‰ < −28.18 ± 0.31‰) and more enriched Δ14C values (−6.94 ± 11.07‰ > −93.74 ± 6.76‰). The δ13C–Δ14C tracing revealed that plants were the primary DOC source for AHR (61 ± 2%), whereas algae dominated DOC sources in GSL (70 ± 2%). Inflow rivers and water retention time (WRT) likely drive differences in DOC sources and concentrations between the two reservoirs. The absence of inflow rivers and the longer WRT in GSL created favorable conditions for algal growth, resulting in substantially higher chlorophyll a (Chl.a) concentrations (103.00 ± 29.87 μg/L > 13.10 ± 3.29 μg/L) and enhanced production of autochthonous DOC through a stronger biological carbon pump (BCP) effect. These conditions further facilitate the formation and accumulation of recalcitrant DOC (RDOC), ultimately increasing DOC concentrations in GSL. Our findings highlight that closed karst reservoirs may represent important yet underappreciated carbon sinks and should receive greater attention in future carbon-sink assessments.

✓ 已验证 DOI 高影响因子
查看原文 查看 PubMed
JOURNAL OF APPLIED POLYMER SCIENCE · 2026 · IF 3.1

Design and Performance Investigation of a Self-Healing Anti-Flashover Coating Based on β-Cyclodextrin–Adamantane Host–Guest Interactions

Bo Zhu,Shijie Xu,Yu Feng,Weijie Xu,Ji Liu,Xinlao Wei

Surface flashover is a common insulation failure in high-voltage equipment. Conventional anti-flashover coatings can raise flashover voltage, but scratches and microcracks often reduce their long-term reliability because most coatings cannot repair damaged interfaces. Here, a self-healing anti-flashover coating was prepared by introducing β-cyclodextrin–adamantane host–guest units into a fluorocarbon resin (FEVE) matrix. Quantum chemical calculations, molecular dynamics simulations, and electrical tests were used to examine host–guest stability, trap regulation, charge dissipation, scratch healing, and DC flashover behavior. The β-CD–Ad inclusion structure was thermodynamically favorable and remained stable during simulation. HG incorporation changed the surface trap distribution of FEVE and promoted charge transport by introducing high-density shallow traps. The 10 wt% HG/FEVE coating showed the best overall performance, with a DC flashover voltage 15.12% higher than that of pure FEVE. After damage and water-assisted repair, it retained 96.57% of its flashover performance. The improved performance is attributed to two coupled effects: reversible host–guest interactions help close damaged interfaces, while shallow-trap-dominated charge transport reduces surface charge accumulation and local electric-field distortion. This work offers a route for designing repairable anti-flashover coatings for high-voltage insulation.

✓ 已验证 产品关联 DOI 高影响因子
查看原文 查看 PubMed
已复制

文献关联基于可获得的产品、CAS、DOI 及引用记录。收录不代表作者或出版方对阿拉丁产品的背书,请以原始文献为准。