计算溶液所需的质量、体积或浓度。
产品内容
|
产品简介
本产品是一种高效的 RNase 灭活及 DNA 清洁剂。它含有多种成分,能高效灭活 玻璃和塑料表面、空气中的 RNase 和 DNA 污染,保障工作环境的清洁。经 RNase 和 DNA 清除剂清洗过的容器、实验台面、枪头、移液枪、电泳槽等等,可确保不含 RNase 和 DNA 污染。
实验前准备及重要注意事项
1.RNase和 DNA 清除剂可直接使用,请勿稀释,稀释后会降低灭活效力。
2.操作人员在使用 RNase和 DNA 清除剂过程中要戴手套,避免皮肤直接接触。使用 喷雾瓶时请戴口罩并在通风橱等通风环境下进行,以防对人产生刺激。
操作步骤
1.用RNase and DNA Remover 处理工作平台 直接将RNase and DNA Remover 喷于台面,待其自然晾干。
2.用RNase and DNA Remover 处理实验仪器 用浸有 RNase and DNA Remover 吸水纸擦拭仪器表面,待其自然晾干。 一些小 的仪器部分可直接浸泡在RNase and DNA Remover 溶液中,晾干后使用。
3.用RNase and DNA Remover 处理玻璃和塑料器皿 将器皿浸泡在RNase and DNA Remover 溶液中或将RNase and DNA Remover 溶 液喷洒在器皿表面,倒立晾干后备用。如处理离心管,可直接将RNase and DNA Remover 溶液加入离心管中,进行涡旋震荡,离心后去除RNase and DNA Remover 溶液,蒸馏水 冲洗两次, 晾干后备用。
4.用RNase and DNA Remover 处理移液枪 根据生产厂家的使用手册卸下移液枪的前端,留下接口塞和圈套后将其浸泡在 RNase and DNA Remover 中,晾干后,将移液枪按使用手册组装好。
5.用RNase and DNA Remover 处理实验室内空气
将RNase and DNA Remover 喷洒在空气中,喷洒时注意戴好口罩、手套等防护用
品,喷洒后请离开现场。若不慎入眼,请立即用清水冲洗或就医。
Products content

Products Introduction
This product is a highly effective RNase inactivation and DNA cleaner. It contains a variety of ingredients that can efficiently inactivate RNase and DNA contamination on glass and plastic surfaces and in the air, ensuring a clean working environment. Containers, lab bench tops, gun heads, pipette guns, electrophoresis tanks, etc. cleaned with RNase and DNA cleaner are guaranteed to be free of RNase and DNA contamination.
Pre-experiment Preparation and Important Notes
1. RNase and DNA scavenger can be used directly, do not dilute, dilution will reduce the inactivation effectiveness.
2. The operator should wear gloves during the use of RNase and DNA Scavenger to avoid direct skin contact. Wear a mask and use the spray bottle in a ventilated environment such as a fume hood to prevent irritation.
procedure
1. Treat the workbench with RNase and DNA Remover Spray RNase and DNA Remover directly onto the workbench surface and allow it to dry naturally.
2. Treat the instrument with RNase and DNA Remover Wipe the surface of the instrument with absorbent paper soaked in RNase and DNA Remover and allow it to dry naturally. Some small parts of the instrument can be directly immersed in the RNase and DNA Remover solution and allowed to dry.
3. Treatment of glass and plasticware with RNase and DNA Remover Soak the vessels in RNase and DNA Remover solution or spray RNase and DNA Remover solution on the surface of the vessels, and let them dry upside down. For centrifuge tubes, add RNase and DNA Remover solution directly to the centrifuge tube, vortex, centrifuge, remove RNase and DNA Remover solution, rinse twice with distilled water, and allow to air dry.
4. Treat the pipette gun with RNase and DNA Remover Remove the front end of the pipette gun according to the manufacturer's instruction manual, leave the interface plug and ferrule in place, soak it in RNase and DNA Remover, allow it to dry, and assemble the pipette gun according to the instruction manual.
5. Use RNase and DNA Remover to treat the air in the experiment room Spray RNase and DNA Remover into the air, wear masks, gloves and other protective products when spraying, and leave the site after spraying. In case of accidental eye contact, flush with water or seek medical advice immediately.